Developing the Low-Temperature Oxidation Mechanism of Cyclopentane: An Experimental and Theoretical Study

At present, the reactivity of cyclic alkanes is estimated by comparison with acyclic hydrocarbons. Due to the difference in the structure of cycloalkanes and acycloalkanes, the thermodynamic data obtained by analogy are not applicable. In this study, a molecular beam sampling vacuum ultraviolet photoionization time-of-flight mass spectrometer (MB-VUV-PI-TOFMS) was applied to study the low-temperature oxidation of cyclopentane (CPT) at a total pressure range from 1–3 atm and low-temperature range between 500 and 800 K. Low-temperature reaction products including cyclic olefins, cyclic ethers, and highly oxygenated intermediates (e. g., ketohydroperoxide KHP, keto-dihydroperoxide KDHP, olefinic hydroperoxides OHP and ketone structure products) were observed. Further investigation of the oxidation of CPT – electronic structure calculations – were carried out at the UCCSD(T)-F12a/aug-cc-pVDZ//B3LYP/6-31+ G(d,p) level to explore the reactivity of O₂ molecules adding sequentially to cyclopentyl radicals. Experimental and theoretical observations showed that the dominant product channel in the reaction of CPT radicals with O₂ is HO₂ elimination yielding cyclopentene. The pathways of second and third O₂ addition – the dissociation of hydroperoxide – were further confirmed. The results of this study will develop the low-temperature oxidation mechanism of CPT, which can be used for future research on accurately simulating the combustion process of CPT.     

坚硬顶板爆破切顶在沿空留巷中的应用研究

当煤层上方为坚硬顶板时,在工作面回采期间容易出现大面积悬顶,导致巷旁充填体出现大变形破坏,极大威胁采煤安全.为解决这一问题,以某矿1205工作面沿空留巷为工程背景,分析了爆炸围岩裂隙范围和坚硬顶板破断特征,建立了切顶卸压围岩结构力学模型,研究表明,相邻炮孔爆炸后,炮孔间裂隙互相贯穿,降低了顶板强度,同时当切顶角为15°时,巷道稳定性较好.工程实践结果表明:采用爆破切顶技术后,顶板下沉量减小了62.3%,较好地保证了围岩稳定性.     

基于XPS对硫铁矿去除SeO2-3的机理研究

硒是动植物及人体生长必需的十五种微量元素之一，具有清除体内自由基、抗氧化、增强免疫力等功能，但其安全剂量的范围却很窄。利用扫描电子显微镜（SEM）和X射线衍射仪（XRD）对湿法球磨制备的硫铁矿形貌进行了表征。SEM观测发现加乙醇助磨后的硫铁矿为粒径大小较均匀的球形颗粒团聚体，粒径范围在17～200 nm之间，平均粒径138 nm。XRD衍射图谱中的特征峰与FeS₂衍射图谱中各峰位置基本一致，因此判定硫铁矿中主要化学组分为FeS₂，且图谱中基本没有杂峰，表明制备过程中并未混入杂质，样品纯度较高。实验结果表明，该法制备的硫铁矿具有颗粒粒径小、比表面积大、反应活性高等优点。研究中利用X射线光电子能谱仪（XPS）对硫铁矿去除水体中SeO2-₃的机理进行了研究。研究结果表明, （1）在较为广泛的实验pH范围（pH 2.2～11.5），硫铁矿均能有效去除水体中SeO2-₃，去除效率（除pH值7.8以外）均达到90%以上；（2）硫铁矿与SeO2-₃发生反应后，其主要组成元素的XPS特征峰结合能有所减小，表明硫铁矿表面发生了一定化学变化；（3）酸碱环境下硫铁矿去除SeO2-₃的机理不完全相同，酸性环境下，硫铁矿对SeO2-₃的去除是单纯的氧化还原过程，即硫铁矿中被酸活化的S2-₂将SeO2-₃还原为单质Se(0)，并且酸性越强，SeO2-₃去除效果越好；碱性环境下，SeO2-₃的去除过程中氧化还原与络合反应并存，硫铁矿表面有络合态Fe(OH)SeO₃和单质Se(0)两种存在形态，且碱性越强，络合态Fe(OH)SeO₃含量越高。以上研究结果为硫铁矿去除固定水体和土壤中以SeO2-₃为代表的可变价金属阴离子提供重要理论依据和应用基础。     

A New Quassinoid from Brucea javanica

Chemistry of Natural Compounds - A new quassinoid, dehydrobruceantinol B (1), was isolated from the seeds of Brucea javanica, together with two known compounds, bruceantinol (2) and bruceine A (3)....     

Fluid‐structure coupling of linear elastic model with compressible flow models

Cavitation erosion is caused in solids exposed to strong pressure waves developing in an adjacent fluid field. The knowledge of the transient distribution of stresses in the solid is important to understand the cause of damaging by comparisons with breaking points of the material. The modeling of this problem requires the coupling of the models for the fluid and the solid. For this purpose, we use a strategy based on the solution of coupled Riemann problems that has been originally developed for the coupling of 2 fluids. This concept is exemplified for the coupling of a linear elastic structure with an ideal gas. The coupling procedure relies on the solution of a nonlinear equation. Existence and uniqueness of the solution is proven. The coupling conditions are validated by means of quasi‐1D problems for which an explicit solution can be determined. For a more realistic scenario, a 2D application is considered where in a compressible single fluid, a hot gas bubble at low pressure collapses in a cold gas at high pressure near an adjacent structure.     

Nanocomposite hydrogel consisting of Na‐montmorillonite with enhanced mechanical properties

A new kind of nanocomposite (NC) hydrogel with Na‐montmorillonite (MMT) is presented in this article. The NC hydrogels were synthesized by free radical copolymerization of acrylamide and (3‐acrylamidopropyl) trimethylammonium chloride (ATC) in the presence of MMT and N,N′‐methylene‐bis‐acrylamide used as chemical cross‐linker. Due to the cation‐exchange reaction between MMT and ATC (cationic monomer) during the synthesis of NC hydrogels, MMT platelets were considered chemical “plane” cross‐linkers, different from “point” cross‐linkers. With increasing amount of MMT, the crosslinking degree enhanced, causing a decrease of the swelling degree at equilibrium. Investigations of mechanical properties indicated that NC hydrogels exhibited enhanced strength and toughness, which resulted from chemical interaction between exfoliated MMT platelets and polymer chains in hydrogels. Dynamic shear measurements showed that both storage modulus and loss modulus increased with increasing MMT content. The idea described here provided a new route to prepare hydrogels with high mechanical properties by using alternative natural Na‐MMT. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1020–1026     

Organocatalytic asymmetric chlorinative dearomatization of naphthols

An organocatalytic asymmetric chlorinative dearomatization of naphthols was realized for the first time, providing chiral naphthalenones with a Cl-containing all-substituted stereocenter in excellent yields and enantioselectivity (up to 97% yield and 96% ee). The reaction features mild reaction conditions, good tolerance of diverse functional groups and simple reaction operation.     

A post curing strategy toward the feasible covalent adaptable networks in polyacrylate latex films

The implementation of covalent adaptable networks (CANs) in general resin system is becoming attractive. In this work, we propose a simple post-curing strategy based on the core-shell structured acrylate latex for the achievement on both the improved general performance and the CANs characteristics in latex films. The building to the CANs was relied on the introduction of 4,4′-diaminophenyl disulfide as the curing agent, which cured the acetoacetoxy decorated shell polymer through the ketoamine reaction. The metathesis reaction of aromatic disulfides in the crosslinking segments enabled the thermally induced dynamic behavior of the network as revealed in the stress relaxation tests by comparison with other diamine crosslinking agents without the incorporation of disulfide. The synergism of the dynamic crosslinking of the shell polymer and static crosslinking in the core polymer contributed to the improved mechanical strength (15 MPa, strain% = 250%) and the suppressed water adsorption (~1% in 24 h of soaking) of the latex film, which exhibited above 90% of recovery in both strength and strain from a cut-off film damage within 1 h at 80°C. Moreover, the cured latex film could be recycled, and 75% of the mechanical performance was regained after three fragmentation-hot-pressing cycles. These, in addition with the feasible and environmental friendly characteristics, suggest a sustainable paradigm toward the smart thermosetting latex polymers.