Buckling of laminated plates - A simple finite element based on higher-order theory

A four-noded rectangular element with seven degrees of freedom at each node is developed for buckling analysis of laminated plate structures having any number of layers with a constant thickness of individual layers. The displacement model is so chosen that it can explain adequately the parabolic distribution of transverse shear stresses and the non-linearity of in-plane displacements across the thickness. A geometrical stiffness matrix is developed using in-plane stresses. A wide range of plates from thick to thin are examined under uniaxial loading conditions. The results are compared with the existing analytical and numerical solutions. The present formulations confirm its applicability for buckling analysis of a wide range of plates.     

The application of Hölder exponent to traffic congestion warning

In this paper, we applied multifractal modeling techniques to analyze the traffic data collected from the Beijing Yuquanying. The results indicated that multifractal characteristics obviously exist in the traffic system; the degree of fractality of these traffic data tends to increase as the traffic system becomes congested; the Hölder exponent that measures the local rate of fractality may be used as indicators to predict the presence of the traffic congestion.     

A highly specific polyclonal antiserum to the environmental contaminant 1,1,1-trichloro-2,2-bis-(4-chlorophenyl)-ethane (p,p′-DDT)

A very selective polyclonal antiserum against 1,1,1-trichloro-2,2-bis-(4-chlorophenyl)-ethane (p,p′-DDT) was obtained by a careful choice of the haptenic structure (2,2-bis(4-chlorophenyl)-ethanol hemisuccinate). This hapten was conjugated to BSA to prepare the immunogen. The effects of different types of solid phases on the equilibrium reaction between the hapten on solid phase and the polyclonal antiserum were evaluated to obtain a fine tuning of the antiserum performances in terms of specificity for p,p′-DDT and sensitivity to low levels of this pesticide. The calibration curves obtained show that it is possible to set up a sensitive assay for p,p′-DDT, employing a p,p′-dichlorodiphenylacetic acid-based solid phase, with a detection limit of 0.12 ng/mL and a working range of about 0.21–40 ng/mL. Selectivity towards several p,p′-DDT-related substances was good (o,p-DDT 17%, p,p′-DDD 1.2% o,p-DDD 6.3%, p,p′-DDE 6.7%).     

Phase diagram of softly repulsive systems: the Gaussian and inverse-power-law potentials

We redraw, using state-of-the-art methods for free-energy calculations, the phase diagrams of two reference models for the liquid state: the Gaussian and inverse-power-law repulsive potentials. Notwithstanding the different behaviors of the two potentials for vanishing interparticle distances, their thermodynamic properties are similar in a range of densities and temperatures, being ruled by the competition between the body-centered-cubic (bcc) and face-centered-cubic (fcc) crystalline structures and the fluid phase. We confirm the existence of a reentrant bcc phase in the phase diagram of the Gaussian-core model, just above the triple point. We also trace the bcc-fcc coexistence line of the inverse-power-law model as a function of the power exponent n and relate the common features in the phase diagrams of such systems to the softness degree of the interaction.     

Electrospun cellulose acetate fibers: effect of solvent system on morphology and fiber diameter

This paper reports an investigation of the effects of solvent system, solution concentration, and applied electrostatic field strength (EFS) on the morphological appearance and/or size of as-spun cellulose acetate (CA) products. The single-solvent systems were acetone, chloroform, N,N -dimethylformamide (DMF), dichloromethane (DCM), methanol (MeOH), formic acid, and pyridine. The mixed-solvent systems were acetone–DMAc, chloroform–MeOH, and DCM–MeOH. Chloroform, DMF, DCM, MeOH, formic acid, and pyridine were able to dissolve CA, forming clear solutions (at 5% w/v), but electrospinning of these solutions produced mainly discrete beads. In contrast, electrospinning of the solution of CA in acetone produced short and beaded fibers. At the same solution concentration of 5% (w/v) electrospinning of the CA solutions was improved by addition of MeOH to either chloroform or DCM. For all the solvent systems investigated smooth fibers were obtained from 16% (w/v) CA solutions in 1:1, 2:1, and 3:1 (v/v) acetone–DMAc, 14–20% (w/v) CA solutions in 2:1 (v/v) acetone–DMAc, and 8–12% (w/v) CA solutions in 4:1 (v/v) DCM–MeOH. For the as-spun fibers from CA solutions in acetone–DMAc the average diameter ranged between 0.14 and 0.37 μm whereas for the fibers from solutions in DCM–MeOH it ranged between 0.48 and 1.58 μm. After submersion in distilled water for 24 h the as-spun CA fibers swelled appreciably (i.e. from 620 to 1110%) but the physical integrity of the fibrous structure remained intact.     

The effects of polymer chain rigidification, zeolite pore size and pore blockage on polyethersulfone (PES)-zeolite A mixed matrix membranes

The polyethersulfone (PES)-zeolite 3A, 4A and 5A mixed matrix membranes (MMMs) were fabricated with a modified solution-casting procedure at high temperatures close to the glass transition temperatures (T_g) of polymer materials. The effects of membrane preparation methodology, zeolite loading and pore size of zeolite on the gas separation performance of these mixed matrix membranes were studied. SEM results show the interface between polymer and zeolite in MMMs experiencing natural cooling is better (i.e., less defective) than that in MMMs experiencing immediate quenching. The increment of glass transition temperature (T_g) of MMMs with zeolite loading confirms the polymer chain rigidification induced by zeolite. The experimental results indicate that a higher zeolite loading results in a decrease in gas permeability and an increase in gas pair selectivity. The unmodified Maxwell model fails to correctly predict the permeability decrease induced by polymer chain rigidification near the zeolite surface and the partial pore blockage of zeolites by the polymer chains. A new modified Maxwell model is therefore proposed. It takes the combined effects of chain rigidification and partial pore blockage of zeolites into calculation. The new model shows much consistent permeability and selectivity predication with experimental data. Surprisingly, an increase in zeolite pore size from 3 to 5 Å generally not only increase gas permeability, but also gas pair selectivity. The O₂/N₂ selectivity of PES-zeolite 3A and PES-zeolite 4A membranes is very similar, while the O₂/N₂ selectivity of PES-zeolite 5A membranes is much higher. This implies the blockage may narrow a part of zeolite 5A pores to approximately 4 Å, which can discriminate the gas pair of O₂ and N₂, and narrow a part of zeolites 3A and 4A pores to smaller sizes. It is concluded that the partial pore blockage of zeolites by the polymer chains has equivalent or more influence on the separation properties of mixed matrix membranes compared with that of the polymer chain rigidification.     

Studies on the preparation and exchange reactions of 5-deuterated uracils

The mechanism of base catalyzed proton exchange at the 5-position of uracil and its N-methylated derivatives has been studied. These reactions proceed by addition — elimination across the 5,6-double bond when the 1-nitrogen is substituted with a methyl group, or with anchimeric assistance of the N-1 anion if the 1-position is unsubstituted. The base catalyzed hydrolyses of 1,3-dimethyluracil and 3-methyluracil also appear to proceed through hydrated intermediates. A facile method for an acid catalyzed preparation of 5-deuterated uracils is described as well as a simple and accurate method for analysis of deuterium content.     

A highly specific polyclonal antiserum to the environmental contaminant 1,1,1-trichloro-2,2-bis-(4-chlorophenyl)-ethane (p,p′-DDT)

A very selective polyclonal antiserum against 1,1,1-trichloro-2,2-bis-(4-chlorophenyl)-ethane (p,p′-DDT) was obtained by a careful choice of the haptenic structure (2,2-bis(4-chlorophenyl)-ethanol hemisuccinate). This hapten was conjugated to BSA to prepare the immunogen. The effects of different types of solid phases on the equilibrium reaction between the hapten on solid phase and the polyclonal antiserum were evaluated to obtain a fine tuning of the antiserum performances in terms of specificity for p,p′-DDT and sensitivity to low levels of this pesticide. The calibration curves obtained show that it is possible to set up a sensitive assay for p,p′-DDT, employing a p,p′-dichlorodiphenylacetic acid-based solid phase, with a detection limit of 0.12 ng/mL and a working range of about 0.21–40 ng/mL. Selectivity towards several p,p′-DDT-related substances was good (o,p-DDT 17%, p,p′-DDD 1.2% o,p-DDD 6.3%, p,p′-DDE 6.7%). Received: 4 November 1996 / Revised: 9 June 1997 / Accepted: 16 June 1997     

Mode of termination in the copolymerization of vinyl acetate–isobutyl methacrylate and methyl methacrylate–methyl acrylate at 60°C

The mode of termination in the vinyl acetate–isobutyl methacrylate (VA–IBMA) and methyl methacrylate–methyl acrylate (MMA–MA) copolymerization systems has been investigated at 60°C. by using the dye-interaction technique for functional endgroup estimation. The results show that pairs of poly(vinyl acetate) radicals interact almost exclusively through a disproportionation mechanism. In the homopolymerization of methyl methacrylate and methyl acrylate, about 1.16 and 1.22 carboxyl-containing endgroups per polymer molecule have been estimated, which shows the predominance of disproportionation over combination in these termination reactions. In poly(isobutyl methacrylate) about 1.55 tagged initiator fragments per chain indicate that 29% of the total radicals terminate through the disproportionation mechanism. Cross termination in the (VA–IBMA) copolymerization system occurs almost entirely through combination for monomer feeds richer in isobutyl methacrylate content while for the MMA–MA system, combination is more important at intermediate monomer feed ratios. These results have been discussed in the light of different explanations for the reaction mechanism.     

Effect of the Media on the Quantum Yield of Singlet Oxygen (O2(1Δg)) Production by 9H‐Fluoren‐9‐one: Solvents and Solvent Mixtures

We have investigated the effect of a series of 18 solvents and mixtures of solvents on the production of singlet molecular oxygen (O₂(¹Δ_g), denoted as ¹O₂) by 9H‐fluoren‐9‐one (FLU). The normalized empirical parameter E derived from E_T(30) has been chosen as a measure of solvent polarity using Reichardt's betaine dyes. Quantum yields of ¹O₂ production (Φ_Δ) decrease with increasing solvent polarity and protic character as a consequence of the decrease of the quantum yield of intersystem crossing (Φ_ISC). Values of Φ_Δ of unity have been found in alkanes. In nonprotic solvents of increasing polarity, Φ_ISC and, therefore, Φ_Δ decrease due to solvent‐induced changes in the energy levels of singlet and triplet excited states of FLU. This compound is a poor ¹O₂ sensitizer in protic solvents, because hydrogen bonding considerably increases the rate of internal conversion from the singlet excited state, thus diminishing Φ_Δ to values much lower than those in nonprotic solvents of similar polarity. In mixtures of cyclohexane and alcohols, preferential solvation of FLU by the protic solvent leads to a fast decrease of Φ_Δ upon addition of increasing amounts of the latter.