Structure determination of KScS2, RbScS2 and KLnS2 (Ln = Nd,Sm, Tb,Dy, Ho,Er, Tm and Yb) and crystal–chemical discussion

The title structures of KScS₂ (potassium scandium sulfide), RbScS₂ (rubidium scandium sulfide) and KLnS₂ [Ln = Nd (potassium neodymium sufide), Sm (potassium samarium sulfide), Tb (potassium terbium sulfide), Dy (potassium dysprosium sulfide), Ho (potassium holmium sulfide), Er (potassium erbium sulfide), Tm (potassium thulium sulfide) and Yb (potassium ytterbium sulfide)] are either newly determined (KScS₂, RbScS₂ and KTbS₂) or redetermined. All of them belong to the α‐NaFeO₂ structure type in agreement with the ratio of the ionic radii r³⁺/r⁺. KScS₂, the member of this structural family with the smallest trivalent cation, is an extreme representative of these structures with rare earth trivalent cations. The title structures are compared with isostructural alkali rare earth sulfides in plots showing the dependence of several relevant parameters on the trivalent cation crystal radius; the parameters thus compared are c, a and c/a, the thicknesses of the S—S layers which contain the respective constituent cations, the sulfur fractional coordinates z(S²⁻) and the bond‐valence sums.     

Influence of copper solute on the creep rate sensitivities of aluminium

The presence of copper atoms as continuous networks at the grain boundaries of an aluminium-copper alloy has been considered not preventing the moving of dislocations during creep (or at least partially). The dislocations can bs absorbed by these boundaries and penetrate through them. That leads to changés of shape and structure of grains and also to the sliding of grains against each other. This was deduced from the accelerating increase in the sensitivity of the steady state creep rate to the applied stress of an aluminium 2·8 wt% copper alloy examined at wide range of temperatures (50–350 °C) and applied stresses (7–170 MPa). This rapid increase in the sensitivity parameter of the steady state creep rate occurs in Al-Cu alloys at quite higher ranges of applied stresses and may be attributed mainly to the contribution of the grain boundary movements to the creep strain.     

Indirect Methods For Determination of The Protective Effects of Coating Films on The Surface of Crystals

The extents of the protective effects of coating films on the surface of crystals were determined. Three different samples were made with different quantities of coating fluid (Sepifilm LP 010 in 10% aqueous solution). Since the atomizing rate was constant, the coating time increased in parallel with the volume of coating fluid applied. The direct measurement of film thickness and smoothness is very difficult, and therefore indirect methods were used. Dimenhydrinate was chosen as model drug; this is a heat-sensitive antihistamine with a low melting point. This temperature can be reached during the tableting process. The behaviour of samples on exposure to heat was examined by differential scanning calorimetry. The water uptakes of the samples were determined with an Enslin apparatus. Plasticity was studied with an instrumented tablet machine. These indirect methods (thermal conductivity, water uptake and plasticity measurements) revealed connections between the results of the various experiments. An overlong coating time decreased the protective effect of the coating film. This revised version was published online in August 2006 with corrections to the Cover Date.     

Time Evolution of Vibration-Induced Excited State Decay

A simple model consisting of two electronic levels and one vibrational mode (phonon) was theoretically studied. The electronic-vibrational interaction was linear in the vibrational displacement. The vibrational mode was taken in the harmonic approximation and was attached to the thermal bath formed by the ambient environment. The kinetic constants of the vibrational dissipation were of the second order in the vibrational-bath coupling and were taken in the Markovian limit. Although, depending on the parameters of the model, different curves of the non-radiative vibration-induced excited state decay were obtained, in general, three time intervals, corresponding to different physical behaviour, were found. In the short-time interval, small oscillations superimposed on the excited state decay were observed. They were determined by the vibrational frequency and influenced by electronic-vibrational coupling. In the middle-time interval, almost quasi-exponential decay was detected; its rate constant increased with stronger electronic-vibrational interaction and speed of vibrational relaxation. In the long-time interval, the decay was very slow and, under special conditions, even an asymptotic non-zero excited state population was observed. Its value increased with the strength of the off-diagonal electron-vibrational coupling. Links of the parameters of the model with quantum chemical terms were estimated.     

Über die Dichten von Soda- und Ätznatron lösungen

Ohne Zusammenfassung     

Magnetic poly(N‐isopropylacrylamide) microspheres by dispersion and inverse emulsion polymerization

The aim of this study was to develop novel thermally responsive polymer microspheres with magnetic properties. Dispersion and inverse emulsion copolymerization of N‐isopropylacrylamide (NIPAAm) and N,N′‐methylenebisacrylamide (MBAAm) was investigated in the presence of γ‐Fe₂O₃ nanoparticles. The resulting microspheres were characterized in terms of morphology, size, polydispersity, iron content, and temperature‐dependent swelling using optical microscopy, transmission electron microscopy, scanning electron microscopy, QELS, and AAS. The effects of several variables, such as the concentration of γ‐Fe₂O₃, MBAAm crosslinking agent, Span 80 surfactant, 2,2′‐azobis(2‐methyloctanenitrile) (AMON) initiator, and polymerization temperature on the properties of the microspheres were studied. Swelling and thermoresponsive behavior of the microspheres containing γ‐Fe₂O₃ nanoparticles were also investigated. The microspheres contained about 8 wt % of iron. The presence of magnetic nanoparticles and their concentration changes did not have any significant effect on the temperature sensitivity of the composites. The particles gradually shrink into an increasingly collapsed state when the temperature is raised to 40 °C since the increase in temperature weakens the hydration and PNIPAAm chains gradually become more hydrophobic, which leads to the collapse of the particles. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5884–5898, 2007