Synthesis and properties of biodegradable elastomeric epoxy modified polyurethanes based on poly(ε-caprolactone) and poly(ethylene glycol)

Biodegradable polyurethane elastomers with potential for applications in medical implants with tunable degradation rate and physical properties were synthesized from reaction of epoxy terminated polyurethanes (EUP) with 1,6-hexamethylene diamine (HMDA) as curing agent. Poly(ε-caprolactone) (PCL) and poly(ethylene glycol) (PEG) as well as 1,6-hexamethylene diisocyanate (HDI) were used for preparation of isocyanate terminated polyurethanes which were subsequently blocked with glycidol to prepare EUPs. All materials were characterized by conventional methods, and their properties were studied fully. Results showed that elastomers based on PEG exhibit superior degradation rate and inferior mechanical properties in comparison to elastomers based on PCL. Optimum degradation rate and mechanical properties were obtained from elastomers made from mixture of PCL and PEG base EUPs.     

Mathematical modeling of a slurry reactor for DME direct synthesis from syngas

In this paper,an axial dispersion mathematical model is developed to simulate a three-phase slurry bubble column reactor for direct synthesis of dimethyl ether(DME) from syngas.This large-scale reactor is modeled using mass and energy balances,catalyst sedimentation andsingle-bubble as well as two-bubbles class flow hydrodynamics.A comparison between the two hydrodynamic models through pilot plantexperimental data from the literature shows that heterogeneous two-bubbles flow model is in better agreement with the experimental data thanhomogeneous single-bubble gas flow model.Also,by investigating the heterogeneous gas flow and axial dispersion model for small bubblesas well as the large bubbles and slurry(i.e.including paraffins and the catalyst) phase,the temperature profile along the reactor is obtained.Acomparison between isothermal and non-isothermal reactors reveals no obvious performance difference between them.The optimum values ofreactor diameter and height were obtained at 7 m and 50 m,respectively.The effects of operating variables on the axial catalyst distribution,DME productivity and CO conversion are also investigated in this research.     

A novel microwave assisted reverse micelle fabrication route for Th (IV)‐MOFs as highly efficient adsorbent nanostructures with controllable structural properties to CO and CH4 adsorption: Design,and a systematic study

Reducing gas contaminants by affordable and effective adsorbents is a major challenge in the 21^st century. In the present study, thorium metal organic framework (Th‐MOF) nanostructures are introduced as highly efficient adsorbents. These compounds were manufactured via a novel route resulting from the development of microwave assisted reverse micelle (MARM) and ultrasound assisted reverse micelle (UARM) methods. The products were characterized utilizing XRD, SEM, TGA/DSC, BET, and FT‐IR analyses. Based on the results, the samples synthesized by MARM had uniform size distribution, high thermal stability, and significant surface area. Calculations using DFT/B3LYP indicated that the compounds have a tendency to the polymeric form, which could theoretically confirm the formation of Th‐MOF. Results of analysis of variance (ANOVA) showed that synthesis parameters played a critical role in the manufacturing of products with distinctive properties. Response surface methodology (RSM) predicted the possibility of creating Th‐MOF adsorbents with the surface area of 2579 m²/g, which was a considerable value in comparison with the properties of other adsorbents. Adsorption studies showed that, in the optimum conditions, the Th‐MOF products had high adsorption capacity for CO and CH₄. It is believed that the synthesis protocol developed in the present study and the systematic studies conducted on the samples which lead to products with ideal adsorption properties.     

Molybdenum (VI)‐functionalized UiO‐66 provides an efficient heterogeneous nanocatalyst in oxidation reactions

A novel heterogeneous nanocatalyst was established by supporting molybdenum (VI) on Zr₆ nodes in the structure of the well‐known UiO‐66 metal–organic framework (MOF). The structure of the UiO‐66 before and after Mo (VI) immobilization was confirmed with XRD, DR‐FTIR and UV–vis spectroscopy, and the presence and amount of Mo (VI) was identified by X‐ray photoelectron spectroscopy and inductively coupled plasma atomic emission spectroscopy. TEM imaging confirmed the absence of Mo clusters on the MOF surface, while SEM confirmed that the appearance of the MOF has not changed upon immobilizing the Mo (VI) catalyst. BET adsorption measurements were used to confirm the porosity of the catalyst. The catalytic activity of this heterogeneous catalyst was investigated in oxidation of sulfides with H₂O₂ in acetonitrile and oxidative desulfurization of dibenzothiophene. Easy work up, convenient and steady reuse and high activity and selectivity are prominent properties of this new hybrid material.     

Preparation of magnetic polyurethane rigid foam nanocomposites

Super paramagnetic Fe₃O₄@SiO₂ nanoparticle was incorporated into polyurethane rigid foams in order to prepare new corresponded magnetic nanocomposite foams via one-shot method. The core–shell-structured nanoparticles were prepared by sol–gel method and characterized by transmission electron microscopy, X-ray diffraction, as well as Fourier transform infrared spectroscopy techniques. Magnetic nanoparticles were used up to 3 % in the foam formulations and the samples prepared successfully. Thermal, mechanical, and magnetic properties of nanocomposites were studied and the results showed superior properties in comparison with pristine foams.     

Determination trace amounts of thallium after separation and preconcentration onto nanoclay loaded with 1-(2-pyridylazo)-2-naphthol as a new sorbent

A procedure has been proposed for the separation and preconcentration of trace amounts of thallium. It is based on the adsorption of thallium ions onto organo nanoclay loaded with 1-(2-pyridylazo)-2-naphthol (PAN). Thallium ions were quantitatively retained on the column in the pH range of 3.5–6.0, whereas quantitative desorption occurs with 5.0?mL of 5% ascorbic acid and thallium was determined by flame atomic absorption spectrometry. Linearity was maintained between 0.66?ng?mL^?1–15.0?µg?mL^?1?in initial solution. Detection limit was 0.2?ng?mL^?1?in initial solution and preconcentration factor was 150. Eight replicate determinations of 2.0?µg?mL^?1 of thallium in final solution gave a relative standard deviation of ±1.48%. Various parameters have been studied, such as the effect of pH, breakthrough volume and interference of a large number of anions and cations and the proposed method was used to determine thallium ions in water and standard samples. Determination of thallium ions in standard sample showed that the proposed method has good accuracy.     

A new molecularly imprinted polymer for selective extraction and pre‐concentration of guaifenesin in different samples: Adsorption studies and kinetic modeling

This paper describes the synthesis of a molecularly imprinted polymer by chemical oxidation of pyrrole as the functional monomer, and at the presence of guaifenesin as the template. The prepared polymer was used as adsorbent in molecularly imprinted solid‐phase extraction followed by spectrophotometric determination. Different parameters in the solid‐phase extraction including sample pH, adsorbent weight, washing solution, and elution solvent were studied to determine optimum conditions for isolation and enrichment of guaifenesin. The results showed guaifenesin was quantitatively adsorbed on the molecularly imprinted polymer at pH 6.0 and completely eluted with an ethanol–water solution (50% v/v). An enrichment factor of four with satisfactory recoveries (87.0–95.0%) was obtained. The solid‐phase extraction columns could be used for up to six consecutive elution‐loading cycles without significant decreases in the analyte recoveries. The method had a dynamic range of 3.0 × 10^?6–1.5 × 10^?4 mol/L with a limit of detection and limit of quantification of 1.4×10^?6 and 4.5×10^?6 mol/L, respectively. The proposed procedure was used for the extraction and determination of guaifenesin in different pharmaceutical formulations, with satisfying results being achieved.     

A digital implementation of 2D Hindmarsh–Rose neuron

Nonlinear Dynamics - Different architectures and techniques have developed in the neuromorphic field to mimic and investigate the activity of biological neural networks. This paper presents a set...     

DC-Pulsed Plasma for Dry Reforming of Methane to Synthesis Gas

The carbon dioxide reforming of methane to synthesis gas under DC-pulsed plasma was investigated. The effects of specific input energy and feed ratio on the product distribution and also feed conversion was studied. At the input energy of about 11 eV/molecule per methane and/or carbon dioxide the feed conversion of 38% for CH₄ and 28% for CO₂ and product selectivity of 74% has been attained for H₂ and CO at feed flow rate of 90 ml/min. The energy consumption in this work displays potential to further study and optimization of the process. The importance of the electron impact reactions in the process was discussed. The results show that by prudent tuning of system variables, the process be able to run in the way of synthesis gas, instead of hydrocarbon production.     

Plasma with two-negative ions and immobile dust particles: planar and non-planar ion-acoustic wave propagation

By using the hydrodynamic equations of positive and two negative ions, Boltzmann electron density distribution, and Poisson equation with immobile positive/negative dust particles, a cylindrical Korteweg-de Vries (CKdV) equation is derived for small but finite amplitude ion-acoustic waves. At the critical total negative ion concentration and/or the critical density rate of the second-negative ions, the pulses collapse at this limit as nonlinearity fails to balance dispersion. Then the CKdV equation is not appropriate to describe the system. Therefore, the modified CKdV (MCKdV) and extended CKdV (ECKdV) equations are derived at the critical plasma compositions and in the vicinity of the critical plasma compositions, respectively. The physical parameters of two plasma environments (e.g., Xe⁺–F^-–SF₆^-_{6}^{-} and Ar⁺–F^-–SF₆^-_{6}^{-} plasmas) are examined on the wave phase velocity and the nonlinear localized pulse profile. The latter should satisfy necessary condition to exist. The localized pulse of Ar⁺–F^-–SF₆^-_{6}^{-} plasma is much spiky than Xe⁺–F^-–SF₆^-_{6}^{-} plasma. Thus, the mass ratio of the negative-to-positive ions is focused upon and it emphasizes to play an important role on the pulse profile. Dependence of the geometrical divergence on the pulse profile is also investigated, which indicates that the localized pulse damps with time. The implications of our results agrees with the experimental observations.