Affinity chromatographic purification of bovine lung endothelin receptor using biotinylated endothelin and avidin-agarose.

Endothelin receptor was purified from bovine lung by affinity chromatography using biotinylated endothelin and avidin-agarose. Endothelin was biotinylated with sulphosuccinimidyl 2-(biotinamido)ethyl-1,3-dithiopropionate, a reactive form of biotin with a cleavable spacer arm containing a disulphide bond designed for a simple elution by thiols. Starting from 3.5 kg of bovine lung, about 200 micrograms of pure receptor were obtained.     

Specific interaction between polyethylenimine and azo dyes carrying hydroxyl groups

The binding of acid azo dyes having phenolic hydroxyl groups such as orange I ( I ), orange II ( II ), chrome violet ( III ), 4-hydroxyazobenzene-4′-sulfonate ( IV ), and 2,4-dihydroxyazobenzene-4′-sulfonate ( V ) by polyethylenimine was studied by equilibrium dialysis and spectroscopic methods. The results obtained indicate that dyes ( III ) and ( V ) with two OH groups are bound much more strongly than dyes ( I ), ( II ), and ( IV ) with one OH group. Also polyethylenimine is far superior to any other polymers which have been examined, including bovine serum albumin, polyvinylpyrrolidone, and poly-L -lysine, in its ability to form complexes with these dyes ( III ) and ( V ). The OH groups involved participate preferentially in complex formation with polyethylenimine. The unusual affinity of polyethylenimine for the dyes carrying OH groups is discussed.     

Sol-Gel Preparation and Photoelectrochemical Properties of Fe2TiO5 Thin Films

Polycrystalline Fe₂TiO₅ films were prepared on nesa silica glass substrates by the sol-gel method, and their photoanodic properties were measured in a three-electrode wet cell with an aqueous buffer solution of pH = 7. Gel films were crystallized into Fe₂TiO₅ when fired at 500°C. The photoanodic current significantly increased when the films were fired at 700°C, and then decreased with increasing firing temperature. Thicker films obtained by repeating the gel film deposition and firing showed smaller photocurrent, and the 50 nm thick film prepared via non-repetitive deposition exhibited the maximum photocurrent. Although the photoresponse was extended to wavelengths near 500 nm, the maximum quantum yield was as low as 0.12 at a wavelength of 340 nm.     

Sol–gel preparation and properties of hydroxypropylcellulose–titania hybrid thin films

Hydroxypropylcellulose (HPC)–titania hybrid thin films were prepared by sol–gel method where titanium tetraisopropoxide Ti(OC₃H₇ ⁱ )₄ was hydrolyzed under acidic conditions in the presence of HPC, followed by dip-coating and drying at 120 °C for 24 h. The viscosity average molecular weight of HPC was 55,000–70,000 or 110,000–150,000, and the TiO₂/(HPC + TiO₂) mass ratio ranged from 0 to 1, which was calculated on the assumption that all Ti(OC₃H₇ ⁱ )₄ is converted into TiO₂. The films were 0.35–1.0 μm thick, transparent in visible region and opaque in ultraviolet (UV) region, where the optical absorption coefficient in UV region increased with increasing titania content. The refractive index increased with increasing titania content, ranging from 1.6 to 1.8 for the hybrid thin films. The pencil hardness increased from 6B to 5H, the durability in hot water significantly increased and the contact angle of water on films increased from 35° to 89° with increasing titania content. Crack-free films could be deposited on organic polymer substrates irrespective of titania or HPC contents, where cracking did not occur at higher HPC contents even when the substrate was bent.     

Control of optical properties of gel-derived oxide coating films containing fine metal particles

Control of the optical properties of gel-derived oxide films containing fine metal particles is described. The duration of the aging of Si(OC₂H₅)₄-derived sols and the amount of water for hydrolyzing Si(OC₂H₅)₄ were found to greatly affect the size and the shape of Au particles formed in the silica matrix, and accordingly the optical absorption of the Au/SiO₂ composite films. Employing dielectric media with high refractive indices like TiO₂ was shown to shift the absorption peak of Au particles to longer wavelengths. Pd/TiO₂ and Pt/TiO₂ composite films showed absorption in the visible region.     

Binding of metal ions by polyethylenimine and its derivatives

Measurements have been made of the binding of divalent metal ions, Cu²⁺, Ni²⁺, Co²⁺, and Zn²⁺ ions, by polyethylenimine (PEI) and its acetyl or alkyl derivatives by the equilibriumdialysis technique. These metal ions, in particular the Cu²⁺ ion, exhibited tremendously remarkable binding affinity toward PEI. The extent of complexation of the polymer with the metal ions was decreased markedly by acetylation or alkylation of the polymer. PEI with no primary amine showed an appreciable decrease in its affinity for the metal ion. These results indicate the participation of the primary amine of the polymer in the formation of the complex. A cooperative binding isotherm was observed in PEI–metal ion complex formation, suggesting swelling or conformational change of the polymer induced by this coordination process. Binding of the Cu²⁺ ion by PEI was found to be essentially independent of temperature over the range 5–35°C.     

Flow analysis of silicate rocks for zirconium

A flow analysis system involving the on-line configuration of an anion-exchange column has been examined to enrich and determine trace concentrations of zirconium of several ppm to hundred ppm levels in silicate rocks and minerals. About 100 mg of sample is decomposed by fusion with a mixture of boric acid and lithium carbonate and taken up with 1M hydrochloric acid to a total of 100 ml. Depending upon the concentration of zirconium, either a 1- or 4-ml aliquot is introduced into an aqueous carrier stream, merged with sulphuric acid and passed through a small volume anion-exchange column. The enriched zirconium is then back eluted with hydrochloric acid, colour-developed with Arsenazo III, and detected spectrophotometrically at 665 nm.     

Sol-Gel Processing of Transparent PLZT((Pb,La)(Zr,Ti)O3) Fibers

PLZT((Pb,La)(Zr,Ti)O₃) ceramic fibers were prepared by the sol-gel method from a solution of lead acetate trihydrate, lanthanum isopropoxide, zirconium n-propoxide and titanium isopropoxide containing 2-methoxyethanol as the solvent. The as-drawn gel fibers were pretreated in an autoclave and preheated in flowing H₂O vapor prior to the heat-treatment for crystallization. The effects of autoclaving and preheating in flowing H₂O vapor on the structure and composition of the resultant fibers were investigated. Optically transparent single phase perovskite PLZT fibers of 5–15 m in thickness and 5 cm in length were successfully prepared when the autoclave-treatment and the preheating in flowing H₂O vapor were conducted prior to crystallization. These treatments are thought to promote hydrolysis of the organic groups and polycondensation reaction in the gel fibers, leading to the successful formation of dense, crack-free transparent PLZT fibers.     

Methyltriethoxysilane-derived sol-gel coatings doped with silver metal particles

Silica sol-gel films were prepared by dipping, starting from an acid catalyzed solution of methyltriethoxysilane (MTES) and tetraethoxysilane (TEOS). Silver metal nanoparticles were produced in the silica layer by introducing in the sol-gel precursor solution AgNO₃ or AgClO₄·H₂O. The silver ions were thermally reduced in air at 800°C, giving an intense yellow coating film. The silver metal particles were observed by transmission electron microscopy and X-ray diffraction. The diameter of the silver particles was found to be about 10 nm. Absorption measurements in the UV-Vis were used to evaluate the volume fraction of silver colloids embedded in the silica layer.     

Binding of methyl orange and its homologs by polyion complexes consisting of a piperidinium cationic polymer and various polyanions in aqueous solution

A study was made of the formation of polyion complexes between a piperidinium cationic polymer and polyanions and of the binding of azo-dye anions (methyl, ethyl, propyl, and butyl orange) by these complexes. Sodium poly(acrylate), poly(styrenesulfonate), dextran sulfate, and carboxy-methylcellulose were used as polyanions. The resultant polyion complexes (insoluble in aqueous solutions) were compared for their ability to bind the small organic molecules in aqueous solutions, for example, of urea and an inorganic electrolyte (KCI), and exhibited a strong binding affinity toward these small anions. Polyion complexes that consisted of sodium poly(acrylate), dextran sulfate, and carboxymethylcellulose as polyanions cooperated in the binding, whereas the polyion complex of sodium poly(styrenesulfonate) did not. It was suggested that small organic anions interact with the polyion complexes primarily through electrostatic and hydrophobic forces.