Adsorption-penetration studies of glucose oxidase into phospholipid monolayers at the 1,2-dichloroethane/water interface.

The interaction between glucose oxidase (GOx) and phospholipid monolayers is studied at the 1,2-dichloroethane/water interface by electrochemical impedance spectroscopy. Electrochemical experiments show that the presence of GOx induces changes in the capacitance curves at both negative and positive potentials, which are successfully explained by a theoretical model based on the solution of the Poisson-Boltzmann equation. These changes are ascribed to a reduced partition coefficient of GOx and an increase of the permittivity of the lipid hydrocarbon domain. Our results show that the presence of lipid molecules enhances the adsorption of GOx molecules at the liquid/liquid interface. At low lipid concentrations, the adsorption of GOx is probably the first step preceding its penetration into the lipid monolayer. The experimental results indicate that GOx penetrates better and forms more stable monolayers for lipids with longer hydrophobic tails. At high GOx concentrations, the formation of multilayers is observed. The phenomenon described here is strongly dependent on 1) the GOx and lipid concentrations, 2) the nature of the lipid, and 3) the potential drop across the interface.     

Determination of volatile corrosion inhibitors by capillary electrophoresis

In this work, a capillary electrophoresis (CE) method using indirect UV detection (214nm) for the simultaneous determination of monoethanolamine (MEA), diethanolamine (DEA), triethanolamine (TEA), diethylethanolamine (DEEA), monocyclohexylamine (MCHA) and dicyclohexylamine (DCHA) in water/ethanol extracts of wrapping materials containing volatile corrosion inhibitors (VCIs) was described. A running buffer consisting of 0.010 molL(-1) imidazole, 0.010 molL(-1) 2-hydroxyisobutyric acid (HIBA) and 0.010 molL(-1) 18-crown-6 ether enabled separation of the analytes in less than 7 min. A few method validation parameters were determined revealing good migration time repeatability (<0.7% RSD) and area repeatability (< 1.8% RSD). Limits of detection were in the range of 0.52-1.54 mg L(-1). Recovery values were in the range of 94.8-100.9%. The methodology was successfully applied to the analysis of three commercial products (VCI treated paper, foam and plastic). The concentration of amines in these materials varied from 0.050 to 22.3% (w/w).     

Influence of the tannin structure on the disruption effect of carbohydrates on protein-tannin aggregates

The disrupting effect of three different ionic carbohydrates (xanthan, pectin and gum arabic) on the formation of tannin-protein insoluble aggregates was assessed by nephelometry using bovine serum albumin (BSA) and several procyanidin fractions previously extracted from grape seeds. The presence in solution of any of the carbohydrates studied was found to restrain the formation of insoluble protein-tannin aggregates for every procyanidin fraction used. Xanthan was the most effective carbohydrate, whereas gum arabic was the least effective. The present work has revealed that the disrupting effect of carbohydrates is quite different depending on the procyanidin structure complexity. In general, the three carbohydrates studied revealed a similar trend in that their disrupting effect on tannin-BSA aggregate formation decreased with increase of the procyanidin degree of polymerization.     

Methylation of Chitosan with Iodomethane: Effect of Reaction Conditions on Chemoselectivity and Degree of Substitution

N,N,N‐trimethylchitosan (TMC) was prepared by reacting purified chitosan with iodomethane, in the presence of sodium hydroxide, water and sodium iodide, at room temperature. The reaction medium was N‐methyl‐2‐pyrrolidone. Different samples of TMC were obtained by adding to the reaction medium a fixed volume (5.5 mL) of aqueous NaOH solutions at different concentrations (15, 20, 30 and 40 wt.‐%) and carrying out the reactions for 9 or 24 h. The features observed in the ¹H and ¹³C NMR spectra of these chitosan derivatives, in respect of the chemical shift, number and relative intensity of the signals, depended strongly on the excess of NaOH and H₃CI added to the reaction medium, but when the lowest excess was employed, the characteristics of the derivative were not affected by the reaction time to the same extent. The average degree of quaternization of these N‐methylated derivatives of chitosan ranged from 10.5% to 44.8%, according to the reaction conditions. Increasing the excess of NaOH, in reactions carried out for 9 h, resulted in TMC samples with progressively higher content of trimethylated sites however, the reaction yields were correspondingly lower and O‐alkylation was favored in these cases.

¹H NMR spectrum of sample [A_X]^24h dissolved in D₂O (C_p = 10 g/L).     

Multi-technique surface characterization of bio-based films from sisal cellulose and its esters: a FE-SEM, μ-XPS and ToF-SIMS approach

Bio-based films were prepared from LiCl/DMAc solutions containing sisal cellulose esters (acetates, butyrates and hexanoates) with different degrees of substitution (DS 0.7–1.8) and solutions prepared with the cellulose esters and 20 wt% sisal cellulose. A novel approach for characterizing the surface morphology utilized field emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry (ToF-SIMS) and contact angle analysis. XPS and ToF-SIMS were a powerful combination while investigating both the ester group distribution on the surface and effects of cellulose content on the film. The surface coverage by ester aliphatic chains was estimated using XPS measurements. Fibrous structures were observed in the FE-SEM images of the cellulose and bio-based films, most likely because the sisal cellulose chains aggregated during dissolution in LiCl/DMAc. Therefore, the cellulose aggregates remained after the formation of the films and removal of the solvent. The XPS results indicated that the cellulose loading on the longer chain cellulose esters films (DS 1.8) increased the surface coverage by ester aliphatic chains (8.2 % for butyrate and 45 % for hexanoate). However, for the shortest ester chains, the surface coverage decreased (acetate, 42 %). The ToF-SIMS analyses of cellulose acetate and cellulose hexanoate films (DS 1.8) revealed that the cellulose ester groups were evenly distributed across the surface of the films.     

Derivatization-free determination of aminoglycosides by CZE–UV in pharmaceutical formulations

Aminoglycosides are a relevant class of antibiotics widely used by medics and veterinaries. There are a variety of reasons that make their determination relevant, such as quality control, environment and food contamination assessment, drug-release studies, among others. The lack of a chromophore makes aminoglycoside spectrophotometric detection particularly challenging, often requiring derivatization. In this work, an indirect detection method, making use of imidazole as a probe, applying CZE was successfully tested. It did not require derivatization, which simplified the sample preparation. Suitable figures of merit were obtained; recoveries between 95 and 105%, adequate repeatability and precision, correlation coefficients (r) above 0.998, and limits of detection (LODs) of 3.2 and 11 mg/L for gentamicin and paromomycin, respectively. As a proof-of-concept, it was also applied in a simple controlled release experiment that was well fitted using the Hill equation.