静止轨道星载差分吸收光谱仪CCD成像系统设计

静止轨道卫星差分吸收光谱仪采用摆扫成像方式对大气进行探测,针对其工作时CCD成像系统信噪比大于1 000、高速探测模式下探测周期小于10min、高分辨率模式下探测周期小于1h的要求,进行CCD成像系统设计.选取CCD47-20作为探测器,设计成像电路实现光谱图像信号的采集和上传.分析了帧叠加和像元合并对时间、空间分辨率的影响.结合帧转移CCD的特点设计了每个位置最后一帧读出时摆镜转动的成像方式,并合理设置了帧叠加数和像元合并数,达到优化成像周期的目的.1s曝光时间条件下,该CCD成像系统的高速、高分辨率模式探测周期分别为515s和3 315s,图像信噪比均大于1 000,污染物观测实验中未出现失帧或重复的现象.该CCD成像系统方案满足静止轨道星载差分吸收光谱仪的探测需求,为静止轨道环境监测仪器设计提供参考.     

Wavelength and power monitoring of DWDM systems using scanning F–P filter calibrated with a F–P laser

A novel technique to overcome the long-term drift and hysteresis of a scanning Fabry–Perot filter was developed and applied to wavelength and power monitoring of DWDM system. By using the comb peaks generated by a temperature-stabilized, near threshold-biased Fabry–Perot diode laser as wavelength reference for the scanning Fabry–Perot filter, wavelength and power measurement accuracy of better than ±10 pm and 0.2 dB, respectively, were achieved.     

第一类永动机幻梦的破灭

介绍了13~18世纪物理学史和科技史上曾名噪一时的第一类永动机的设计方案的破灭.第一类永动机幻梦破灭的历史引起了人们的反思与启示,有力地促进了19世纪中叶能量转化和守恒定律的确立.     

Active long pulse shaping technique of pulsed CO2 laser using multi-pulse discharge control

We describe the pulse forming of pulsed CO₂ laser using multi-pulse superposition technique. Various pulse shapes, high duty cycle pulse forming network (PFN) are constructed by time sequence. This study shows a technology that makes it possible to make various long pulse shapes by activating SCRs of three PFN modules consecutively at a desirable delay time with the aid of a PIC one-chip microprocessor. The power supply for this experiment consists of three PFN modules. Each PFN module uses a capacitor, a pulse forming inductor, a SCR, a high voltage pulse transformer, and a bridge rectifier on each transformer secondary. The PFN modules operate at low voltage by driving the primary of HV pulse transformer. The secondary of the transformer has a full-wave rectifier, which passes the pulse energy to the load in a continuous sequence.We investigated various long pulse shapes as different trigger time intervals of SCRs among three PFN modules. As a result, we could obtain laser beam with various pulse shapes and durations from about 250 to 1000 μs.     

Hydrodynamic Properties of Fe3O4 Kerosene-Based Ferrofluids with Narrow Particle Size Distribution

We investigate the hydrodynamic properties of Fe3O4 kerosene-based ferrofluids with narrow particle size distribution. The ferrofluids are synthesized by improving chemical coprecipitation technique. A narrow distribution of 8.6-10.8nm particle sizes is obtained from the magnetization curve with the free-form model based on the Bayesian inference theory. The fitting result is consistent with average particle size obtained from x-ray diffraction. With the increase of applied magnetic field and magnetic particle concentration, apparent viscosity of ferrofluids increases. At concentration 4.04%, the type of flow for the ferrofluid transforms from Newtonian to Bingham plastic fluid as the applied magnetic field increases.     

The glow curve structure for the LiF:Mg,Cu,Na,Si TL detector with dopants concentrations and sintering temperatures

The glow curve structures for LiF:Mg,Cu,Na,Si TL detectors with various dopant concentrations and sintering temperatures were investigated for the improvement of the glow curve structure and sensitivity of the TL detector. The dopant concentrations were varied over the following ranges: Mg (0–0.25 mol%), Cu (0–0.07 mol%), Na and Si (0–1.5 mol%). With increasing Cu concentration, the intensity of the main peak was intensified and reached a maximum at a concentration of 0.05 mol%. The high-temperature peak was reduced. The dependency of the main peak intensity on the Mg concentration exhibits a sharp maximum at 0.2 mol%. The intensity of the high-temperature peak tends to rise slightly with increasing Mg concentration. It was found that the optimum concentrations of the dopants in the LiF:Mg,Cu,Na,Si TL material are Mg: 0.2 mol%, Cu: 0.05 mol%, Na and Si: 0.9 mol%. The dependency of the main peak intensity on sintering temperature exhibits a very sharp maximum at 830°C. The high-temperature peak was rapidly reduced after 825°C.     

Pressure and temperature dependence of the gas‐transport properties of dense poly[2,6‐toluene‐2,2‐bis(3,4‐dicarboxylphenyl)hexafluoropropane diimide] membranes

The gas‐transport properties of poly[2,6‐toluene‐2,2‐bis(3,4‐dicarboxylphenyl)hexafluoropropane diimide] (6FDA‐2,6‐DAT) have been investigated. The sorption behavior of dense 6FDA‐2,6‐DAT membranes is well described by the dual‐mode sorption model and has certain relationships with the critical temperatures of the penetrants. The solubility coefficient decreases with an increase in either the pressure or temperature. The temperature dependence of the diffusivity coefficient increases with an increase in the penetrant size, as the order of the activation energy for the diffusion jump is CH₄ > N₂ > O₂ > CO₂. Also, the average diffusion coefficient increases with increasing pressure for all the gases tested. As a combined contribution from sorption and diffusion, permeability decreases with increases in the pressure and the kinetic diameter of the penetrant molecules. Even up to 32.7 atm, no plasticization phenomenon can be observed on flat dense 6FDA‐2,6‐DAT membranes from their permeability–pressure curves. However, just as for other gases, the absolute value of the heat of sorption of CO₂ decreases with increasing pressure at a low‐pressure range, but the trend changes when the feed pressure is greater than 10 atm. This implies that CO₂‐induced plasticization may occur and reduce the positive enthalpy required to create a site into which a penetrant can be sorbed. Therefore, a better diagnosis of the inherent threshold pressure for the plasticization of a glassy polymer membrane may involve examining the absolute value of the heat of sorption as a function of pressure and identifying the turning point at which the gradient of the absolute value of the heat of sorption against pressure turns from a negative value to a positive one. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 354–364, 2004