Structure of a poly(2,5‐benzimidazole)/phosphoric acid complex

As‐cast films of poly(2,5‐benzimidazole) exhibit uniplanar orientation in which the planes of the aromatic rings lie parallel to the film surface. Upon doping with phosphoric acid, the original crystalline order is lost, but the doped film can be stretched to produce films with uniaxial orientation. After thermal annealing at 540 °C, nine Bragg reflections are resolved in the fiber diagram, and these are indexed by an orthorhombic unit cell with the dimensions a = 18.1 Å, b = 3.5 Å, and c = 11.4 Å, containing four monomer units of two chains. The absence of odd‐order 00l reflections points to a 2₁ chain conformation, which is probably planar so that the aromatic units can be stacked along the b axis. The water and phosphoric acid contents of the crystalline structure cannot be determined exactly because of the presence of extensive amorphous regions that probably have different solvation. The best agreement between the observed and calculated intensities is for an idealized structure containing two phosphoric acids and two water molecules per unit cell. However, the phosphoric acid is probably present mainly in the form of pyrophosphoric acid and its higher oligomers. In addition, the X‐ray data are consistent with a more disordered structure containing chains with random (up and down) polarity and a lack of c‐axis registry. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2576–2585, 2004     

Preparation and electrical characterization of (PVC + KBrO3) polymer electrolytes for solid state battery applications

This paper presents results of studies on dc electrical conductivity and transference number measurements on potassium bromate (KBrO₃) complexed polyvinyl chloride (PVC) films prepared by solution cast technique. Temperature dependence of dc electrical conductivity and transference number data indicated the dominance of ion type charge transport in these specimens. The magnitude of conductivity increased with increase in concentration of the salt and temperature. Using this (PVC + KBrO₃) electrolyte, solid-state electrochemical cells were fabricated, and their discharge profiles were studied under a constant load of 100 kΩ. Several cell profiles such as open circuit voltage, short circuit current, power density, and energy density associated with these cells were evaluated and were reported. The features of complexation of the electrolytes were studied by X-ray diffraction and Fourier transform infrared spectroscopy. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006     

Characterization of synthesizedA-zeolite

Confirmations of the successful synthesis of a particular zeolite demand investigation of the crystals by XRD, SEM, MAS-NMR and chemical analysis. In this work, we have used the DTA exothermic lattice breakdown of theA-zeolite, which gives typical peaks at around 900–1200°C for characterization. The effects ofpH, concentration, time of crystallization and temperature were studied and it was quickly and easily possible to distinguishA-zeolite formation from others originating from the synthesis matrix under different conditions by using DTA/TG analyses. The parameters were optimized for the synthesis of the zeolite and DTA measurements yielded enough information to identify theA-zeolite; this was confirmed by XRD and SEM.     

Na2CO3调质钙基脱硫剂硫化机理实验研究

对经Na2CO3溶液调质石灰石煅烧产物CaO的物理结构及硫化特性进行了研究,发现同等条件下调质后石灰石煅烧产物CaO(M-CaO)比未经调质的CaO(N-CaO)具有更高的钙转化率.利用XRD技术对CaO晶体结构进行了测定,通过比较二者的晶胞参数和晶格畸变度等并结合其孔特性,证实M-CaO之所以比N-CaO具有更高的钙转化率,是由于M-CaO比N-CaO具有更高的晶体缺陷浓度,使得在硫化反应过程中通过产物层的扩散具有更高的离子扩散率.     

Chemical Reactivity of Tetrasulfur Tetranitride: Synthesis,Physical Properties,and Structural Characterization of the Amorphous Phase Cu7S4N4

Tetrasulfur tetranitride, S₄N₄, reacts with elemental Cu within inert solvents to a black‐blue material of approximate composition Cu₇S₄N₄ which is totally amorphous to X‐rays and which cannot be made crystalline by either thermal treatment or electron radiation. Cu₇S₄N₄ explodes if heated above 234 °C or when subjected to mechanical shock to eventually yield copper(I) sulfide; this together with the characteristic infrared spectrum of Cu₇S₄N₄ indicates the presence of molecular S₄N₄ units inside the amorphous phase. The metastable nature of Cu₇S₄N₄ is also mirrored by electron microscopy which furthermore allows the structural characterization of its degradation products. Based on experimental EXAFS data offering characteristic Cu—N and Cu—S distances, a theoretical crystalline approximant of Cu₇S₄N₄ was suggested and structurally optimized by density‐functional total‐energy calculations including periodic boundary conditions. This model incorporates a central S₄N₄ unit bonded to three shells of Cu atoms of different functionalities; in addition, a partial rupture of the S₄N₄ unit is likely to allow for a lowering of the total energy of the metastable phase. The latter observation supports the impossibility to make Cu₇S₄N₄ crystallize using ₄N₄ crystallize using whatever kind of measures.     

60keV质子辐照对TiNi记忆合金薄膜马氏体相变的影响

 利用磁控溅射的方法在氧化后的单晶Si基片上制备了TiNi形状记忆合金薄膜，利用示差扫描量热法和原位X射线衍射研究了薄膜的马氏体相变特征。通过60keV质子注入（辐照）薄膜样品研究了H+离子对合金薄膜马氏体相变特征的影响，结果表明氢离子注入后引起了马氏体相变开始Ms和结束点Mf以及逆马氏体相变开始As和结束温度Af的下降，而对R相变开始Rs和结束温度Rf影响不大。掠入射X射线衍射表明H+离子注入后有氢化物形成。H⁺离子注入形成的氢化物是引起相变点的变化的主要因素。     

Chemical synthesis of p-type nanocrystalline copper selenide thin films for heterojunction solar cells

Nanocrystalline thin films of copper selenide have been grown on glass and tin doped-indium oxide substrates using chemical method. At ambient temperature, golden films have been synthesized and annealed at 200 °C for 1 h and were examined for their structural, surface morphological and optical properties by means of X-ray diffraction (XRD), scanning electron microscopy and UV-vis spectrophotometry techniques, respectively. Cu_2−xSe phase was confirmed by XRD pattern and spherical grains of 30 ± 4 - 40 ± 4 nm in size aggregated over about 130 ± 10 nm islands were seen by SEM images. Effect of annealing on crystallinity improvement, band edge shift and photoelectrochemical performance (under 80 mW/cm² light intensity and in lithium iodide electrolyte) has been studied and reported. Observed p-type electrical conductivity in copper selenide thin films make it a suitable candidate for heterojunction solar cells.     

Preparation and characterization of rigid poly(vinyl chloride)/MMT nanocomposites. II. XRD,morphological and mechanical characteristics

A Haake torque rheometer equipped with an internal mixer is used to study the influence of the amount of sodium montmorillonite (Na⁺‐MMT) and organically modified MMT (O‐MMT) on X‐ray diffraction (XRD), morphology, and mechanical characteristics of rigid poly (vinyl chloride) (PVC)/Na⁺‐MMT and PVC/O‐MMT nanocomposites, respectively. Results of XRD and transmission electron microscopy (TEM) indicate that MMT is partially encapsulated and intercalated in the rigid PVC/Na⁺‐MMT nanocomposites. However, results of XRD and TEM show MMT is partially intercalated and exfoliated in the rigid PVC/O‐MMT nanocomposites. Tensile strength, yield strength, and elongation at break of the rigid PVC/MMT nanocomposites were improved simultaneously with adding 1–3 wt % Na⁺‐MMT or O‐MMT with respect to that of pristine PVC. However, the addition of Na⁺‐MMT or O‐MMT should be kept as not more than 3 wt % to optimize the mechanical properties and the processing stability of the rigid PVC/MMT nanocomposites. SEM micrographs of the fractured surfaces of the rigid PVC/Na⁺‐MMT and PVC/O‐MMT nanocomposites both before and after tensile tests were also illustrated and compared. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2145–2154, 2006     

Pt对Mo基催化剂还原-硫化过程的影响

采用脉冲硫化、连续硫化、程序升温还原、程序升温及程序降温电导及X射线衍射等方法研究了贵金属Pt对MoO3催化剂还原-流化过程的影响及Pt对MOS2配位不饱和活性中心形成的影响．结果表明，Pt担载或在MoO3上可以促进MoO3的还原-硫化，使MoO3的还原-硫化温度大大降低Pt担载在MoSw上可促进MoS2的部分还原形成配位不饱和的钼中心     

Mesoporous micelle templated silica with incorporated C<Subscript>8</Subscript> and C<Subscript>18</Subscript> phase

Mesoporous silica material of MCM-41 type was synthesized by co-condensation of highly concentrated octyltriethoxysilane (OTEOS), octadecyltriethoxysilane (ODTEOS) and tetraethoxysilane (TEOS). The obtained hybrid materials were characterized using XRD, TG-DSC and low temperature adsorption/desorption of nitrogen. It was shown that the applied method of synthesis allows to obtain silica of MCM-41 type with a high degree of hydrocarbon saturation.