双稳态结构中的1/2次谐波共振及其对隔振特性的影响

以典型的双稳态系统——屈曲梁结构为例,基于等效模型,结合解析、数值和实验手段,研究了双稳态结构中的1/2次谐波共振特性、演化过程、参数调节规律及其对隔振特性的影响.研究发现,当非线性刚度系数或激励幅值增加到一定程度时,系统会在一定带宽下产生显著的1/2次谐波共振;随着激励幅值增加,阻尼系统的1/2次谐波遵循“产生-增强-衰退-消失”的过程,该过程对峰值频率和峰值传递率有重要影响;适当提高非线性强度能有效改善双稳态结构隔振特性.针对双稳态屈曲梁结构开展的实验验证了1/2次谐波特性和隔振特性变化规律.     

加肋圆柱壳在轴压作用下的屈曲和后屈曲

本文讨论完善和非完善的,纵向加肋和正交加肋圆柱壳在轴压作用下的屈曲和后屈曲性态.依据文[1]提供的圆柱薄壳屈曲的边界层理论及其分析方法,给出了加肋圆柱壳在轴压作用下的屈曲和后屈曲理论分析.本文同时讨论肋骨与壳板材料不同时对加肋圆柱壳屈曲和后屈曲性态的影响.     

Variational Derivative for Buckling Loads of Beams and Frames

The finite-difference method is a numerical technique for obtaining approximate solutions to differential equations. The main objective of the present study is to give a new aspect to the finite-difference method by using a variational derivative. By applying this formulation, accurate values of the buckling loads of beams and frames with various end supports are obtained. The performance of this formulation is verified by comparison with numerical examples in the literature __________ Published in Prikladnaya Mekhanika, Vol. 41, No. 7, pp. 139–144, July 2005.     

A WKB analysis of the buckling condition for a cylindrical shell of arbitrary thickness subjected to an external pressure

We consider the plane-strain buckling of a cylindrical shellof arbitrary thickness which is made of a Varga material andis subjected to an external hydrostatic pressure on its outersurface. The WKB method is used to solve the eigenvalue problemthat results from the linear bifurcation analysis. We show thatthe circular cross-section buckles into a non-circular shapeat a value of µ₁ which depends on A₁/A₂ and a mode number,where A₁ and A₂ are the undeformed inner and outer radii, andµ₁ is the ratio of the deformed inner radius to A₁. Inthe large mode number limit, we find that the dependence ofµ₁ on A₁/A₂ has a boundary layer structure: it is constantover almost the entire region of 0 < A₁/A₂ < 1 and decreasessharply from this constant value to unity as A₁/A₂ tends tounity. Our asymptotic results for A₁ – 1 = O(1) and A₁– 1 = O(1/n) are shown to agree with the numerical resultsobtained by using the compound matrix method.     

Stability and Nonlinear Deformation of Cylindrical Grids

The general stability of single-layer cylindrical grids is studied in linear and nonlinear formulations. Dependence of the general buckling load on the geometry and stiffness parameters of a grid is established in an analytical form. Such grids are numerically analyzed for stability. It is established that the general buckling load is much less than the local buckling load. Typical general buckling modes are found. It is shown that such grids are weakly sensitive to imperfections     

多段构件组成的压杆平面内稳定

分析由若干段等截面或者变截面构件组成的压杆平面内稳定问题．从由三段等截面构件组成的压杆平面内稳定问题出发，对两端为变截面、中间为等截面构件组成的压杆的平面内稳定问题进行了分析，得出和两端为等截面构件情况类似的屈曲荷载计算公式．并对两端固接的情况进行了研究分析．     

受压矩形截面柱在塑性阶段的缺陷敏感性分析

对加载到塑性阶段的矩形截面柱，本文研究了几何缺陷对屈曲的影响，在分析中考虑了弹性卸载的影响，求出了荷载、缺陷大小及分叉模态幅值之间的精确渐近关系式，结果表明在塑性阶段最大承载力对小缺陷非常敏感，但当缺陷大小达到某一值后，可能不存在最大载荷。     

复合载荷下圆底扁球壳非线性稳定性

本文采用半解析方法研究在中心分布载荷及中心集中力联合作用下,圆底扁球壳的非线性稳定性问题.避免了求近似解析解时繁重的人工计算,而p-W_m特征关系仍可由显式表达.     

An evolutionary method for optimization of plate buckling resistance

Optimization of plate buckling resistance is very complicated, because the in-plane stress resultants in the prebuckled state of a plate are functions of thickness distribution. This paper discusses the problem of finding the optimum thickness distribution of isotropic plate structures, with a given volume and layout, that would maximise the buckling load. A simple numerical method using the finite-element analysis is presented to obtain the optimum thickness distribution. Optimum designs of compression-loaded rectangular plates with different boundary conditions and plate aspect ratios are obtained by using the proposed method. Optimum designs from earlier studies and the methods of buckling analysis used to attain these results are discussed and compared with the designs from the proposed method. This paper also examines the reliability of the optimality criterion generally used for plate buckling optimization, which is based on the uniform strain energy density.     

Relationship between Euler buckling and unstable equilibria of buckled beams

Classic snap-through of curved beams, plates, and shells has long been an object of attention in structural engineering. Euler buckling under axial loading is perhaps an even more entrenched part of the canon of engineering education and practice. In this paper we introduce a relationship between the two phenomena, that to our knowledge has not been directly addressed before. The relationship shows that Euler buckling configurations are connected by the force–displacement curve under transverse loading. The results are used to develop a very simple metric to estimate the number of unstable static equilibria of a buckled structure based only on its geometry with no need for static or dynamic solvers. The study is focused on beams as this allows for an unambiguous discussion of the idea on the simplest possible structure.