Dynamic and buckling analysis of polymer hybrid composite beam with variable thickness

This work deals with a study of the dynamic and buckling analysis of polymer hybrid composite(PHC) beam. The beam has variable thickness and is reinforced by carbon nanotubes(CNTs) and nanoclay(NC) simultaneously. The governing equations are derived based on the first shear deformation theory(FSDT). A three-phase HalpinTsai approach is used to predict the mechanical properties of the PHC. We focus our attention on the effect of the simultaneous addition of NC and CNT on the vibration and buckling analysis of the PHC beam with variable thickness. Also a comparison study is done on the sensation of three impressive parameters including CNT, NC weight fractions, and the shape factor of fillers on the mechanical properties of PHC beams,as well as fundamental frequencies of free vibrations and critical buckling load. The results show that the increase of shape factor value, NC, and CNT weight fractions leads to considerable reinforcement in mechanical properties as well as increase of the dimensionless fundamental frequency and buckling load. The variation of CNT weight fraction on elastic modulus is more sensitive rather than shear modulus but the effect of NC weight fraction on elastic and shear moduli is fairly the same. The shape factor values more than the medium level do not affect the mechanical properties.     

无轴承旋翼柔性梁载荷特性研究

应用Hamilton原理建立了双路传力的无轴承旋翼运动方程。采用均匀入流模型,基于直升机飞行平衡条件,建立了无轴承旋翼柔性梁载荷的计算模型,并通过算例验证了模型的精度。利用该模型,研究了全机重心位置、机身气动阻力以及平尾安装角对柔性梁载荷特性的影响,给出了各因素对柔性梁载荷的影响趋势,得出了降低柔性梁载荷的方法。数值结果表明:2cm左右重心位置的变化能够引起9%~11%的柔性梁载荷变化量,15%气动阻力的增加会导致约9%的柔性梁载荷的增大;2°平尾安装角的变化引起约10%柔性梁载荷的变化量,3°平尾安装角的变化引起约26%柔性梁载荷的变化。     

水硬性石灰合成及拉破坏特性试验研究

水硬性石灰在欧洲石质文物修复和加固中获得了很大成功。我国的石质文物主要是砂岩,水硬性石灰的修复效果不好。为满足我国石质文物修复和加固的需求,本文以石灰石和黏土为原料,在950℃煅烧不同时间,制备出水硬性石,对试样的成分、微观形貌、收缩率、抗拉强度和拉破坏过程等进行了研究。结果表明:(1)试样中含有水硬性成分2CaO·SiO2(C2S);煅烧8h时,成分与欧洲水硬性石灰NHL5接近;1.5CaO·SiO2·xH2O(C-S-H)和CaCO3的含量随龄期的增加逐渐增加。(2)龄期1~3d,收缩率较小;龄期4~6d,收缩率以线性规律增加;7d以后,收缩率趋于稳定。(3)局部变形区随拉应力的增加而变大,邻近局部变形区逐渐合并,形成面积更大的应变局部化带;载荷超过峰值后,产生微裂隙;随载荷进一步增加,微裂隙扩展,贯穿整个试件,发展成宏观裂隙,使试件破坏。(4)抗拉强度随龄期的增加而增加,水硬性石灰中C-S-H、CaCO3等相互交织,构成空间致密体,使试件力学强度提高。合成的水硬性石灰物理力学性能与欧洲水硬性石灰NHL5相近,并且成分均匀、可控,在石质文物修复和加固工程中具有良好应用前景。     

A new Monte Carlo model for predicting the mechanical properties of fiber yarns

Understanding the complicated failure mechanisms of hierarchical composites such as fiber yarns is essential for advanced materials design. In this study, we developed a new Monte Carlo model for predicting the mechanical properties of fiber yarns that includes statistical variation in fiber strength. Furthermore, a statistical shear load transfer law based on the shear lag analysis was derived and implemented to simulate the interactions between adjacent fibers and provide a more accurate tensile stress distribution along the overlap distance. Simulations on two types of yarns, made from different raw materials and based on distinct processing approaches, predict yarn strength values that compare favorably with experimental measurements. Furthermore, the model identified very distinct dominant failure mechanisms for the two materials, providing important insights into design features that can improve yarn strength.     

Structural response of stiffened plates in similitude under a turbulent boundary layer excitation

In structural dynamics, similitude laws usually deal with simple configurations as thin flat plates with point forces. Only recently, few papers have analyzed stiffened shells or stochastic pressure loads.This research activity extends the applicability of some similitude laws, developed for thin flat plates under a turbulent boundary layer load, to ribbed plates forced by the same wall pressure fluctuations.The work addresses the problem of designing a scaled experimental test-article and, successively, of re-modulating the measured data in order to get the structural response of an original (unscaled) configuration.Due to the complexity of the structural domain, the design of a scaled configuration leads to a distorted similitude. Then, a simple approach, to circumvent the distortion effects, is proposed.     

面向装配节点平衡的产品生产物流协调优化研究

在由多个并行零件生产线和装配线组成的产品生产物流中, 各生产线的瓶颈工序制约了装配节点及其整个生产物流的平衡. 为此, 基于约束理论和JIT(Just In Time)思想, 提出主、次瓶颈的概念及其判别方法和主瓶颈拉动次瓶颈、瓶颈前后拉动生产与平行顺序移动生产相结合的生产策略, 研究了基于负荷率的瓶颈工序负荷控制方法和主瓶颈触发次瓶颈拉式生产的时间控制方法, 使瓶颈工序利用率最大化, 各个零件到达装配节点的同步性得到改善. 算例的SIMIO仿真结果表明, 装配节点的在制品存量大幅度减少, 利用率提高.     

群集建筑中大跨裙摆屋盖风荷载特性的数值模拟研究

以苏州太平金融大厦为工程背景,针对其大跨裙摆屋盖的风荷载作用,首先采用RNG k-ε模型模拟分析了其平均风压分布规律,以及风向变化对屋盖表面风荷载体型系数的影响;其次,引入干扰因子IF,探讨了周边建筑对大跨裙摆屋盖风荷载的气动干扰作用。结果表明:0°风向下,走廊上方屋盖两侧区域出现“上吸下顶”的叠加作用;90°风向下屋盖北侧飘带末端区域受到狭道风效应出现正压集中现象;风向变化对大跨裙摆屋盖的风荷载体型系数分布影响较大;且周围建筑物对大跨裙摆屋盖的气动干扰效应明显,主要表现为风压“遮挡效应”,而局部区域表现为风压“放大效应”。     

Two-dimensional magneto-thermoelastic interactions in a micropolar functionally graded solid

Abstract

The present work is concerned with the 2D deformation in a nonhomogeneous, isotropic, micropolar, magneto-thermoelastic medium in the context of Lord-Shulman theory as a result of an inclined load. The inclined load is supposed to be a linear combination of normal load and tangential load. Material properties are assumed to be graded in x-direction. Normal mode technique is proposed to obtain the analytical expressions for the temperature field, displacement components, and stresses. These are also calculated numerically and depicted graphically to observe the variations of the considered physical variables.

Communicated by Seonho Cho.     

The Application of Fractal Transform and Entropy for Improving Fault Tolerance and Load Balancing in Grid Computing Environments

This paper applies the entropy-based fractal indexing scheme that enables the grid environment for fast indexing and querying. It addresses the issue of fault tolerance and load balancing-based fractal management to make computational grids more effective and reliable. A fractal dimension of a cloud of points gives an estimate of the intrinsic dimensionality of the data in that space. The main drawback of this technique is the long computing time. The main contribution of the suggested work is to investigate the effect of fractal transform by adding R-tree index structure-based entropy to existing grid computing models to obtain a balanced infrastructure with minimal fault. In this regard, the presented work is going to extend the commonly scheduling algorithms that are built based on the physical grid structure to a reduced logical network. The objective of this logical network is to reduce the searching in the grid paths according to arrival time rate and path’s bandwidth with respect to load balance and fault tolerance, respectively. Furthermore, an optimization searching technique is utilized to enhance the grid performance by investigating the optimum number of nodes extracted from the logical grid. The experimental results indicated that the proposed model has better execution time, throughput, makespan, latency, load balancing, and success rate.