甲烷浓度对碳化硅基底金刚石薄膜摩擦性能影响

利用热丝化学气相沉积法(HFCVD)在碳化硅基底上制备金刚石薄膜,采用场发射扫描电子显微镜、拉曼光谱仪、原子力显微镜研究了在不同甲烷浓度条件下制备的金刚石薄膜表面形貌及物相组成,在干摩擦条件下通过往复式摩擦磨损实验测试并计算了已制备金刚石薄膜的摩擦系数和磨损率,结合物相分析及摩擦磨损实验结果分析了甲烷浓度的改变对金刚石薄膜摩擦磨损性能的影响。结果表明,由于甲烷气体含量的升高,金刚石薄膜结晶质量下降,薄膜由微米晶向纳米晶转变。摩擦磨损实验结果显示:3%甲烷浓度条件下制备的金刚石薄膜耐磨性较好,磨损率为2.2×10^-7 mm³/mN;5%甲烷浓度条件下制备的金刚石薄膜摩擦系数最低(0.032),磨损率为5.7×10^-7 mm³/mN,制备的金刚石薄膜的耐磨损性能相比于碳化硅基底(磨损率为9.89×10^-5 mm³/mN)提升了两个数量级,显著提高了碳化硅基底的耐磨性。     

Real time estimation of CO2 laser weld quality for automotive industry

Laser welding is one of the most precise welding processes in joining sheet metals. In laser welding, performing real time evaluation of the welding quality is very important to enhance the efficiency of the welding process. In this study, the plasma and spatter, which are generated during laser welding, are measured using UV and IR photodiodes. The factors that influence weld quality are classified into five categories; optimal heat input, slightly low heat input, low heat input, partial joining due to gap mismatch, and nozzle deviation. The data number deviated from reference signals and their standard deviations were also considered to evaluate the qualities. A system was also formulated to perform real time evaluations of the weld quality using a fuzzy multi-feature pattern recognition with the measured signals.     

复合体系方法测量液体力学谱

本文介绍了采用复合体系，测量得到凝聚态物质从固态到液态连续变化力学谱的一种新的实验方法。以簧振动为例，给出了解析的计算公式，以及应用条件。通过进一步综合分析，得到具有更广应用范围的近似公式，可以近似应用于其他不同的振动模式，如低频扭摆。应用新的测量方法，给出了典型小分子玻璃材料甘油和碳酸丙稀从玻璃态到液态的力学谱，观察到甘油和碳酸丙稀玻璃化转变、碳酸丙稀的再结晶、熔化和挥发的过程；测量得到挥发过程中水的质量随时间精确变化的曲线。最后，本文给出了新方法的一些应用展望。     

Nano-tribological study on a super-hydrophobic film formed on rough aluminium substrates

A novel super-hydrophobic stearic acid (STA) film with a water contact angle of 166^o was prepared by chemical adsorption on aluminum wafer coated with polyethyleneimine (PEI) film. The micro-tribological behavior of the super-hydrophobic STA monolayer was compared with that of the polished and PEI-coated Al surfaces. The effect of relative humidity on the adhesion and friction was investigated as well. It was found that the STA monolayer showed decreased friction, while the adhesive force was greatly decreased by increasing the surface roughness of the Al wafer to reduce the contact area between the atomic force microscope (AFM) tip and the sample surface to be tested. Thus the friction and adhesion of the Al wafer was effectively decreased by generating the STA monolayer, which indicated that it could be feasible and rational to prepare a surface with good adhesion resistance and lubricity by properly controlling the surface morphology and the chemical composition. Both the adhesion and friction decreased as the relative humidity was lowered from 65% to 10%, though the decrease extent became insignificant for the STA monolayer. The project supported by the National Natural Science Foundation of China (50375151, 50323007, 10225209) and the Chinese Academy of Sciences (KJCX-SW-L2)     

路径对摩擦力做功的影响

本文通过讨论两种临界情况下摩擦力所做的功的变化情况，进一步阐明非保守力做的功与路径有关．     

Relationship between the dynamic softening transition and wet sliding friction of elastomer compounds

For properly chosen elastomer compounds, thermorheological characterization is combined with an examination of the variation of the wet sliding friction with temperature. A conceptual argument leads to the assumption that the wet sliding friction should maximize at the energy dissipation peak associated with the dynamic softening transition at a characteristic frequency determined by the sliding speed and the effective smallest surface asperity scale. The dynamic softening transition is characterized with the peak in tan δ/G′ⁿ, where tan δ is the loss tangent, G′ is the elastic modulus, and n is a constant between 0 and 1. The William–Landel–Ferry transform is uncritically applied for extrapolating the position of the peak in tan δ/G′ⁿ at high frequencies. Even based on the criterion of tan δ, the results obtained on a concrete surface indicate that the effective smallest asperity scale is of order of 100 μm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2467–2478, 2004     

快冷Fe_(71)Al_(29)合金中的两个内耗峰

用一个计算机控制的倒扭摆研究了快冷Fe71 Al2 9合金中的两个内耗峰 .在快冷的Fe71 Al2 9样品中分别在 180℃(P1 ) ,340℃ (P2 )和 5 10℃ (P3)出现了内耗峰 ,而在慢冷的Fe71 Al2 9样品中只发现了P3峰 .快冷样品中的P1 和P2峰在从 6 5 0℃冷却下来的测量过程中或在 35 0℃经过较长时间的时效后消失 ,其峰高随时效时间的增加而下降 ,直至消失 .P1 和P2 峰都有弛豫特征 ,它们的激活能分别为 :H1 =1.0 3± 0 .0 8eV(P1 峰 ) ;H2 =1.6 4± 0 .0 5eV(P2 峰 ) .P1 峰被认为是无序合金中Al原子在四面体点阵内的最近邻运动所引起 ,P2 峰则是无序合金中Al原子在四面体点阵内的次近邻运动所引起     

爆炸焊接参数的计算机辅助设计

 根据爆炸焊接理论，综合分析了相关爆炸焊接参数的计算方法，利用Visual C++语言编制了爆炸焊接参数计算机辅助设计程序，该程序采用菜单和视图形式对输入、输出命令结果进行操作，方便直观。与有关实验结果的对比表明，计算所给出的焊接窗口及最佳焊接参数具有很高的准确度。爆炸焊接CAD方法对于减少实验次数，摆脱经验设计方法，选择最佳焊接参数将是非常有用的工具。     

Sufficient conditions of non‐uniqueness for the Coulomb friction problem

We consider the Signorini problem with Coulomb friction in elasticity. Sufficient conditions of non‐uniqueness are obtained for the continuous model. These conditions are linked to the existence of real eigenvalues of an operator in a Hilbert space. We prove that, under appropriate conditions, real eigenvalues exist for a non‐local Coulomb friction model. Finite element approximation of the eigenvalue problem is considered and numerical experiments are performed. Copyright © 2003 John Wiley & Sons, Ltd.     

双面电弧焊接的传热模型

将等离子焊接(PAW)电弧和钨极氩弧焊(TIG)电弧串接,相对作用于工件的正反面形成双面电弧焊接(DSAW)系统,可以引导焊接电流沿工件厚度方向流过小孔,补偿等离子电弧穿透工件时消耗的能量,以有效地提高等离子弧的穿透能力.综合考虑影响双面电弧焊接正反面熔池几何形状的力学因素,建立了熔池表面变形的控制方程,以此为基础并采用帖体曲线坐标系建立了DSAW焊接传热的数学模型,分析了DSAW,PAW焊接传热的差异,从传热的角度解释了DSAW焊接熔深增加的原因.焊接工艺实验表明,计算结果与实测结果吻合良好. 关键词： 双面电弧焊接(DSAW) 传热模型 熔池表面变形模型