碳纳米管膜的高温纯化研究

为了获得纯度更高的碳纳米管膜, 保证材料发热稳定性, 需要对通过化学气相沉积法得到的碳纳米管膜进行二次纯化. 通过使用高温纯化炉, 在真空状态下, 从1700℃到3200℃分7挡温度对碳纳米管进行纯化, 并对其含碳量和方块电阻进行比较. 结果表明, 高温纯化后的碳纳米管膜含碳量从95.0%提高到99.9%, 解决了含碳量低的问题. 同时, 在高温纯化中发现碳纳米管膜方块电阻从纯化前3Ω降低到0.5Ω, 方块电阻的降低对碳纳米管膜具有十分重要的意义, 同样对碳纳米管膜后续产品的开发也有重要作用.     

Sonochemical conversion of CO2 into hydrocarbons: The Sabatier reaction at ambient conditions

In this study, we investigated an alternative method for the chemical CO₂ reduction reaction in which power ultrasound (488 kHz ultrasonic plate transducer) was applied to CO₂-saturated (up to 3%) pure water, NaCl and synthetic seawater solutions. Under ultrasonic conditions, the converted CO₂ products were found to be mainly CH₄, C₂H₄ and C₂H₆ including large amount of CO which was subsequently converted into CH₄. We have found that introducing molecular H₂ plays a crucial role in the CO₂ conversion process and that increasing hydrogen concentration increased the yields of hydrocarbons. However, it was observed that at higher hydrogen concentrations, the overall conversion decreased since hydrogen, a diatomic gas, is known to decrease cavitational activity in liquids. It was also found that 1.0 M NaCl solutions saturated with 2% CO₂ + 98% H₂ led to maximum hydrocarbon yields (close to 5%) and increasing the salt concentrations further decreased the yield of hydrocarbons due to the combined physical and chemical effects of ultrasound. It was shown that CO₂ present in a synthetic industrial flue gas (86.74% N₂, 13% CO₂, 0.2% O₂ and 600 ppm of CO) could be converted into hydrocarbons through this method by diluting the flue gas with hydrogen. Moreover, it was observed that in addition to pure water, synthetic seawater can also be used as an ultrasonicating media for the sonochemical process where the presence of NaCl improves the yields of hydrocarbons by ca. 40%. We have also shown that by using low frequency high-power ultrasound in the absence of catalysts, it is possible to carry out the conversion process at ambient conditions i.e., at room temperature and pressure. We are postulating that each cavitation bubble formed during ultrasonication act as a “micro-reactor” where the so-called Sabatier reaction -$C{O}_2+4H_2\stackrel{\mathit{Ultrasonication}}{\to }C{H}_4+2H_{2}O$ - takes place upon collapse of the bubble. We are naming this novel approach as the “Islam-Pollet-Hihn process”.     

Mechanism of BPh3-Catalyzed N-Methylation of Amines with CO2 and Phenylsilane: Cooperative Activation of Hydrosilane

BPh₃ catalyzes the N-methylation of secondary amines and the C-methylenation (methylene-bridge formation between aromatic rings) of N,N-dimethylanilines or 1-methylindoles in the presence of CO₂ and PhSiH₃; these reactions proceed at 30–40 °C under solvent-free conditions. In contrast, B(C₆F₅)₃ shows little or no activity. ¹¹B NMR spectra suggested the generation of [HBPh₃]⁻. The detailed mechanism of the BPh₃-catalyzed N-methylation of N-methylaniline ( 1 ) with CO₂ and PhSiH₃ was studied by using DFT calculations. BPh₃ promotes the conversion of two substrates (N-methylaniline and CO₂) into a zwitterionic carbamate to give three-component species [Ph(Me)(H)N⁺CO₂⁻⋅⋅⋅BPh₃]. The carbamate and BPh₃ act as the nucleophile and Lewis acid, respectively, for the activation of PhSiH₃ to generate [HBPh₃]⁻, which is used to produce key CO₂-derived species, such as silyl formate and bis(silyl)acetal, essential for the N-methylation of 1 . DFT calculations also suggested other mechanisms involving water for the generation of [HBPh₃]⁻ species.     

A post curing strategy toward the feasible covalent adaptable networks in polyacrylate latex films

The implementation of covalent adaptable networks (CANs) in general resin system is becoming attractive. In this work, we propose a simple post-curing strategy based on the core-shell structured acrylate latex for the achievement on both the improved general performance and the CANs characteristics in latex films. The building to the CANs was relied on the introduction of 4,4′-diaminophenyl disulfide as the curing agent, which cured the acetoacetoxy decorated shell polymer through the ketoamine reaction. The metathesis reaction of aromatic disulfides in the crosslinking segments enabled the thermally induced dynamic behavior of the network as revealed in the stress relaxation tests by comparison with other diamine crosslinking agents without the incorporation of disulfide. The synergism of the dynamic crosslinking of the shell polymer and static crosslinking in the core polymer contributed to the improved mechanical strength (15 MPa, strain% = 250%) and the suppressed water adsorption (~1% in 24 h of soaking) of the latex film, which exhibited above 90% of recovery in both strength and strain from a cut-off film damage within 1 h at 80°C. Moreover, the cured latex film could be recycled, and 75% of the mechanical performance was regained after three fragmentation-hot-pressing cycles. These, in addition with the feasible and environmental friendly characteristics, suggest a sustainable paradigm toward the smart thermosetting latex polymers.     

Facile sonochemical synthesis of rutile-type titanium dioxide microspheres decorated graphene oxide composite for efficient electrochemical sensor

In this reports the facile and green synthesis of rutile-type titanium dioxide nanoparticles decorated graphene oxide nanocomposite via the ultrasonication process (frequency: 50 kHz, Power: 100 W/cm² and Ultrasonic type: Ti-horn). Because, the sonochemical synthesis method is simple, non-explosive and harmless method than other conventional technique. Furthermore, the synthesized material was characterized by various analytical techniques including FESEM, EDX, XRD, EIS and electrochemical methods. Then, the synthesized TiO₂ MPs@GOS composite was applied for the electrocatalytic detection of theophylline (TPL) using CV and amperometric (current-time) techniques. Captivatingly, the modified sensor has excellent electrocatalytic performance with the wider linear range from 0.02 to 209.6 µM towards the determination of theophylline and the LOD and sensitivity of the modified sensor was calculated as 13.26 nM and 1.183 μA·µM⁻¹·cm⁻², respectively. In addition, a selectivity, reproducibility and stability of the TiO₂ MPs@GOS modified GCE were analyzed towards the determination of theophylline molecule. Finally, the real time application of TiO₂ MPs@GOS modified theophylline sensor was established in serum and drug samples.     

Mechanistic Aspects of a Highly Active Dinuclear Zinc Catalyst for the Co‐polymerization of Epoxides and CO2

The dinuclear zinc complex reported by us is to date the most active zinc catalyst for the co‐polymerization of cyclohexene oxide (CHO) and carbon dioxide. However, co‐polymerization experiments with propylene oxide (PO) and CO₂ revealed surprisingly low conversions. Within this work, we focused on clarification of this behavior through experimental results and quantum chemical studies. The combination of both results indicated the formation of an energetically highly stable intermediate in the presence of propylene oxide and carbon dioxide. A similar species in the case of cyclohexene oxide/CO₂ co‐polymerization was not stable enough to deactivate the catalyst due to steric repulsion.     

Precise Synthesis and Thin Film Self-Assembly of PLLA-b-PS Bottlebrush Block Copolymers

The ability of bottlebrush block copolymers (BBCPs) to self-assemble into ordered large periodic structures could greatly expand the scope of photonic and membrane technologies. In this paper, we describe a two-step synthesis of poly(l-lactide)-b-polystyrene (PLLA-b-PS) BBCPs and their rapid thin-film self-assembly. PLLA chains were grown from exo-5-norbornene-2-methanol via ring-opening polymerization (ROP) of l-lactide to produce norbornene-terminated PLLA. Norbonene-terminated PS was prepared using anionic polymerization followed by a termination reaction with exo-5-norbornene-2-carbonyl chloride. PLLA-b-PS BBCPs were prepared from these two norbornenyl macromonomers by a one-pot sequential ring opening metathesis polymerization (ROMP). PLLA-b-PS BBCPs thin-films exhibited cylindrical and lamellar morphologies depending on the relative block volume fractions, with domain sizes of 46–58 nm and periodicities of 70–102 nm. Additionally, nanoporous templates were produced by the selective etching of PLLA blocks from ordered structures. The findings described in this work provide further insight into the controlled synthesis of BBCPs leading to various possible morphologies for applications requiring large periodicities. Moreover, the rapid thin film patterning strategy demonstrated (>5 min) highlights the advantages of using PLLA-b-PS BBCP materials beyond their linear BCP analogues in terms of both dimensions achievable and reduced processing time.     

Tuning the Basicity of Cyano‐Containing Ionic Liquids to Improve SO2 Capture through Cyano–Sulfur Interactions

A new approach has been developed to improve SO₂ sorption by cyano‐containing ionic liquids (ILs) through tuning the basicity of ILs and cyano–sulfur interaction. Several kinds of cyano‐containing ILs with different basicity were designed, prepared, and used for SO₂ capture. The interaction between these cyano‐containing ILs and SO₂ was investigated by FTIR and NMR methods. Spectroscopic investigations and quantum chemical calculations showed that dramatic effects on SO₂ capacity originate from the basicity of the ILs and enhanced cyano–sulfur interaction. Furthermore, the captured SO₂ was easy to release by heating or bubbling N₂ through the ILs. This efficient and reversible process, achieved by tuning the basicity of ILs, is an excellent alternative to current technologies for SO₂ capture.     

Strain effects on multiferroic BiFeO3 films

The field of multiferroics has experienced a rapid progress resulting in the discovery of many new physical phenomena. BiFeO₃ (BFO) compound, which is one of the few room-temperature single-phase multiferroics, has contributed subsequently to this progress. As a result, significant review articles have been devoted specifically to this famous system. This chapter is dedicated to the strain effects on the structure stability and property changes of BFO thin films. It is a short and non-exhaustive topical overview that may be seen as an invitation for interested readers to go beyond. There is a very active and prolific research in this field and we apologize to the authors whose relevant work is not cited here. After a short introduction, we will thus review the effect of strain on BFO films by describing the consequences on the structure and the phase transitions as well as on polar, magnetic and magnetoelectric properties.