Northeastern Mathematical Journal Aims and Scope

Northeastern Mathematical Journal （NMJ） is a comprehensive mathematical journal carrying original papers on pure and applied mathematics. It started publication in September, 1985, and appears quarterly. The primary purpose is to present latest achievements in mathematical research and to promote national and international academic exchange. The Editorial Committee of NMJ consists of 49 members from different parts and units of China.     

二元示数计算

(三)负除法不够除情况 若不够除,在负实首处退商(负商),然后在负商位,“+|负商|×法”的排积。若|负商|+|剩商|=10,则负实变正实,剩商是真商,若|负商|+|剩商|=9,则负实仍然存在,但剩商要看作是真商。     

非线性系统可逆的多轨线方法

乌克兰科学院A．M．kovalev教授于1993年首次提出了针对一般非线性系统{x=f(t,x,u)；y=h(t,x,u),x(t0)=x0的多轨线求逆方法。本文将该方法引入仿射非线性系统，使不可逆系统在一定条件下成为可逆。并给出了具体的求逆步骤，举例说明。     

不用特殊转轴的既约梯度方法

无论是Wolfe既约梯度法,还是Zangwill凸单纯形法,在不使用越-韩转轴或类似的转轴运算时,都没得到过令人满意的收敛定理.事实上,那样的收敛定理总是在此非退化假设强很多的不太现实的条件下证得的.本文提出一个新的方法,它介于既约梯度法与凸单纯形法之间.有趣的是,无需特殊的转轴运算,在非退化假设下,我们就     

原子吸收法在有机分析中的应用（Ⅵ）香烟中氢氰酸的分析

原子吸收法在有机分析中的应用（Ⅵ）香烟中氢氰酸的分析谢志海，郎惠云，高云（西北大学化学系，西安，７１００６９）关键词：氢氰酸，测定，原子吸收光谱香烟中的尼古丁，烟焦油等含氮有机物燃烧后将产生氢氰酸，吸入人体后极为有害。国外在这方面的研究始于七十年代，...     

数学分析中的两种基本思想方法—转换与估值

数学分析中的两种基本思想方法──转换与估值邝荣雨（北京师范大学数学系１００８７５）本文试图从方法论的角度，就数学分析的基本内容和基本解题方法进行提炼、归纳和总结．我们称它为数学分析的基本思想方法．我认为它主要包含两种方法：转换（或称变换）方法和估值方...     

价格与隐含远期违约概率

如同根据布莱克-斯科尔斯模型从欧式看涨期权市场价格中反求隐含波动率一样,从信用违约互换的价格中提取隐含违约概率在理论上和实践上都存在很多困难.传统的自助法存在很大的缺点,并有可能得出不符合现实的结果.本文采用基于一段时期的条件违约概率的新的优化方法来替代基于自助法的瞬时远期违约概率,该方法有很多优良特性,会得出比传统方法好得多的结论.     

Self-Assembly of Micro-Parts onto Si Substrates at Liquid-Liquid Interface

We report a new approach for the self-assembly of cuboid micro-parts onto Si substrates to construct three-dimensional microstructures. To perform assembly, the Si substrates are prepared with a deep cavity array as binding sites. An aggregate composed of hundreds of uniformly aligned micro-parts is formed at the C10F18-H2O interface. The micro-parts are arranged by passing the substrate through the aggregate of micro-parts, thus the micro-parts are left on the substrate, and then the substrate is vibrated ultrasonically in the solution, making it possible for the micro-parts to fall into the cavities on the substrate. Finally the substrate is pulled out of the solution after assembly. This technique could give a high yield of up to 70%, providing a new method for micro-assembly.