Two-dimensional windowed Fourier transform for fringe pattern analysis: Principles, applications and implementations

Fringe patterns from optical metrology systems need to be demodulated to get the desired parameters. Two-dimensional windowed Fourier transform is chosen for the determination of phase and phase derivatives. Two algorithms, one based on filtering and the other based on similarity measure, are developed. Some applications based on these two algorithms are explored, including strain determination, phase unwrapping, phase-shifter calibration, fault detection, edge detection and fringe segmentation. Various examples are given to demonstrate the ideas. Finally implementations of these algorithms are addressed. Most of the work has appeared in various papers and its originality is not claimed. Instead, this paper gives an overview and more insights of our work on windowed Fourier transform.     

An Innovative Method for 3-D Shape,Strain and Temperature Full-Field Measurement Using a Single Type of Camera: Principle and Preliminary Results

An innovative technique for measuring both the shape, the displacement, the strain and the temperature fields at the surface of an object using a single stereovision sensor is proposed. The sensor is based on two off-the-shelf low-cost high-resolution uncooled CCD cameras. To allow both dimensional and thermal measurements, the sensor operates in the visible and near infrared (NIR) spectral band (0.7–1.1 μm), and a radiometric and geometric calibration of the sensor is required. This technique leads to a low-cost camera-based simplified instrumentation that gives simultaneously dimensional/kinematical and thermal field measurements.     

Laser metrology — a diagnostic tool in automotive development processes

Laser measurement techniques are widely used in automotive development processes. Applications at Volkswagen are presented where laser metrology works as a diagnostic tool for analysing and optimising complex coupled processes inside and between automotive components and structures such as the reduction of a vehicle's interior or outer acoustic noise, including brake noise, and the combustion analysis for diesel and gasoline engines to further reduce fuel consumption and pollution. Pulsed electronic speckle pattern interferometry (ESPI) and holographic interferometry are used for analysing the knocking behaviour of modern engines and for correct positioning of knocking sensors. Holographic interferometry shows up the vibrational behaviour of brake components and their interaction during braking, and allows optimisation for noise-free brake systems. Scanning laser vibrometry analyses structure-born noise of a whole car body for the optimisation of its interior acoustical behaviour.Modern engine combustion concepts such as in direct-injection (DI) gasoline and diesel engines benefit from laser diagnostic tools which permit deeper insight into the in-cylinder processes such as flow generation, fuel injection and spray formation, atomisation and mixing, ignition and combustion, and formation and reduction of pollutants. The necessary optical access inside a cylinder is realised by so-called ‘transparent engines’ allowing measurements nearly during the whole engine cycle. Measurement techniques and results on double-pulse particle image velocimetry (PIV) with a frequency-doubled YAG laser for in-cylinder flow analysis are presented, as well as Mie-scattering on droplets using a copper vapour laser combined with high-speed filming, and laser-induced fluorescence (LIF) with an excimer laser for spray and fuel vapour analysis.     

TDLAS波长调制压力测量法参数优化

使用TDLAS技术进行动态压力测量已经成为压力测量领域的研究热点。波长调制法实验装置较为复杂,需要对多个参数进行设置,选择出最优的预设参数能够取得更好的实验效果,获得更高的测量精度。目前波长调制法的实验参数设置基本凭借个人经验,使用Matlab程序仿真结合波长调制法的TDLAS测量技术,能够对实验中需要进行预设的重要参数进行了分析。通过计算4990cm-1波段和6330cm-1波段附近的多条吸收峰,发现4990.09cm-1波段处的吸收峰更适合作为波长调制法的测量波段。以4990.09cm-1处的吸收峰为研究对象,进行了波长调制法压力测量仿真建模,计算了调制度、调谐频率和调制频率对二次谐波幅值和对称性的影响并深入地分析了影响因素,总结了其变化规律。在综合考虑抗噪性能和测量精度的情况下,选择了调制度为2.5,调谐频率30Hz,调制频率5kHz为最佳实验参数。基于Matlab的仿真模型能够快速计算大量参数点,更加直观地分析出对参数的影响趋势,为实验仪器和预设参数的选择提供依据。     

Elastic distortions in simple piston-cylinder units at pressures up to 100 MPa

Abstract

The study of elastic distortions in piston-cylinder units of primary standards piston gauges is of importance for the improvement of pressure measurement accuracy. Preliminary work (GF. Molinar et al., 1989) on distortion calculations was carried out on a tungsten carbide (t.c.) piston-cylinder of 0.2 cm² nominal effective area in the 100 MPa pressure range. The same calculations are now applied in the study of a similar piston-cylinder unit of hard steel (h.s.). The distortions on the outer surface of the cylinder are measured with strain gages and with a capacitance sensor. The calculated distortions, which can be also derived with other methods (G. Klingenberg 1989, R. Wisniewski et al. 1989), are compared with the experimental results obtained on the outer surface of the cylinder. The present two piston-cylinder units of h.s. and of t.c. were cross-floated up to 100 MPa and the ratio R = f(P) = Ae_h.s./Ae_t.c. obtained experimentally is compared with the calculated.     

Tip‐enhanced Raman spectroscopy – an interlaboratory reproducibility and comparison study

Since its first experimental realization, tip‐enhanced Raman spectroscopy (TERS) has emerged as a potentially powerful nanochemical analysis tool. However, questions about the comparability and reproducibility of TERS data have emerged. This interlaboratory comparison study addresses these issues by bringing together different TERS groups to perform TERS measurements on nominally identical samples. Based on the spectra obtained, the absolute and relative peak positions, number of bands, peak intensity ratios, and comparability to reference Raman and surface‐enhanced Raman spectroscopy (SERS) data are discussed. Our general findings are that all research groups obtained similar spectral patterns, irrespective of the setup or tip that was used. The TERS (and SERS) spectra consistently showed fewer bands than the conventional Raman spectrum. When comparing these three methods, the spectral pattern match and substance identification is readily possible. Absolute and relative peak positions of the three major signals of thiophenol scattered by 19 and 9 cm⁻¹, respectively, which can probably be attributed to different spectrometer calibrations. However, within the same group (but between different tips), the signals only scattered by 3 cm⁻¹ on average. This study demonstrated the suitability of TERS as an analytical tool and brings TERS a big step forward to becoming a routine technique. Copyright © 2014 John Wiley & Sons, Ltd.     

Line strength and collisional broadening coefficients of H2O at 2.7 μm for natural gas quality assurance applications

We employed tunable diode laser absorption spectroscopy to measure the line strength, the methane (CH₄), ethane (C₂H₆) and the propane (C₃H₈) broadening coefficients for the 523–422 H₂O transition at 3619.61 cm^?1. Water amount fractions generated by a stable and accurate humidity transfer standard, traceable to the SI units via the German national humidity standard, were used to calibrate the spectroscopic line strength measurements. We focus on the traceability of the measured line data to the SI and on uncertainty assessments following the guidelines of the Guide to the Expression of Uncertainty in Measurement. We determined the line strength to be (8.42 ± 0.07)×10^?20 cm^?1/(cm^?2 molecule) corresponding to a relative uncertainty of ±0.8%. To the best of our knowledge, we report the first methane, ethane and propane broadening coefficients of (8.037 ± 0.056)×10^?5 cm^?1/hPa, (9.077 ± 0.064)×10^?5 cm^?1/hPa and (10.469 ± 0.073)×10^?5 cm^?1/hPa for the 523–422 H₂O transition at 3619.61 cm^?1, respectively. The relative combined uncertainties of the stated CH₄, C₂H₆ and C₃H₈ broadening coefficients are in the ±0.7% range.     

线性色散设计的光谱共焦测量技术

研制了高精度的光谱共焦位移测量系统并完成相关测试。基于色差理论和材料优化选择设计一种色差与波长成线性关系的色散物镜,有助于平衡系统在全测量范围的灵敏度。理论分析了系统参数对系统的影响规律,计算了针孔尺寸与系统的分辨率和信噪比的关系,给出了参数优化结果。利用设计的线性色散物镜和参数优化结果,构建了光谱共焦测量系统,完成了系统的校准、测试和应用研究。结果表明,系统的轴向测量范围达到1 mm,分辨力优于0.5μm,全程测量误差小于2μm,符合设计要求。     

气相分子吸收光谱仪的计量校准方法

建立一种科学合理且可操作性强的气相分子吸收光谱仪校准方法。从仪器的工作原理及结构入手,对该类仪器提出了检出限、线性相关系数、定量重复性等性能评价参数。利用国家相关标准物质对其检出限的测量不确定度进行了评定,统一了校准方法,有力地保证了测量数据的准确性、溯源性。对计量技术机构开展该类仪器的校准工作规范的制定有一定的指导意义。