Cold vapour atomic fluorescence determination of mercury in milk by slurry sampling using multicommutation

A highly sensitive mechanized method has been developed for the determination of mercury in milk by atomic fluorescence spectrometry (AFS). Samples were sonicated for 10 min in an ultrasound water bath in the presence of 8% (v/v) aqua regia, 2% (v/v) antifoam A and 1% (m/v) hydroxilamine hydrochloride, and after that, they were treated with 8 mmol l⁻¹ KBr and 1.6 mmol l⁻¹ KBrO₃ in an hydrochloric medium. Atomic fluorescence measurements were made by multicommutation, which provides a fast alternative in quality control analysis, due to the easy treatment of a large number of samples (approximately 70 h⁻¹), and is an environmentally friendly procedure, which involves a waste generation of only 94.5 ml h⁻¹ as compared with the 605 ml h⁻¹ obtained by using continuous AFS measurements. The limit of detection found was 0.011 ng g⁻¹ Hg in the original sample. The method provided a relative standard deviation of 3.4% for five independent analysis of a sample containing 0.30 ng g⁻¹ Hg. To validate the accuracy of the method, a certified reference material NIST-1459 (non-fat milk powder) containing 0.3±0.2 ng g⁻¹ Hg was analysed and a value of 0.27±0.06 ng g⁻¹ Hg was found. A comparison made between data found by the developed procedure and those obtained by microwave-assisted digestion and continuous AFS measurements evidenced a good comparability between these two strategies. Results obtained for commercially available milk samples varied between 0.09 and 0.61 ng g⁻¹ Hg depending on the type of sample and its origin. The confluence of the analytical waste with a 6 mol l⁻¹ NaOH allowed us to reduce the waste generation in a working session from 1 l to 5 g solid residue with a matrix of Fe(OH)₃ which contributes to the deactivation of traces of heavy metals presents in the samples that does not form volatile hydrides.     

高固相含量羟基磷灰石浆料的制备及凝胶浇注成型

为提高羟基磷灰石(HAP)浆料在水分散体系中的稳定性, 获得良好的固化性能, 采用二甲基丙烯酰胺(DMAA)作为单体, N,N’-亚甲基双丙稀酰胺(MBAM)作为交联剂, 偶氮二咪唑啉丙烷(AZIP)为引发剂, 研究了不同分散剂含量和不同固相含量HAP浆料的流变性. 使用自制的亚微米级粉体原料, 制备了固相含量高达55%(体积分数)的稳定浆料, 并成功实现了浇注成型. 获得相对密度高达57.5%的素坯, 其抗压强度、抗弯强度最高值分别达到(37.0±6.5)和(13.8±1.0) MPa. 经1250 ℃无压烧结2 h, HAP陶瓷具有优良的烧结性能, 相对密度为98.7%, 抗弯强度和弹性模量分别达到了(85.3±9.9) MPa 和(133.0±10.2) GPa.     

Simultaneous determination of Cd and Fe in sewage sludge by high-resolution continuum source electrothermal atomic absorption spectrometry with slurry sampling

This work describes the method development for the simultaneous determination of Cd and Fe using the main resonance line of Cd at 228.802 nm and a secondary Fe line at 228.725 nm, and high-resolution continuum source electrothermal atomic absorption spectrometry (HR-CS ET AAS). Two certified reference materials and two ‘real’ samples of industrial and domestic sewage sludge have been analyzed as slurries prepared in a mixture of HF and HNO₃. The simultaneous determination has been performed using a short temperature program of only 30 s, without a pyrolysis stage and with two atomization stages, at 1300 °C and 2300 °C, taking into consideration the significantly different thermal characteristics of Cd and Fe. Structured background, which is likely due to the presence of one or more diatomic molecules, including SiO, has been detected. However, there has been no spectral overlap between molecular bands and the atomic lines of Cd and Fe, making possible the determination to be carried out using only automatic correction for continuous background. Calibration against aqueous standards lead to good agreement between certified or informed values and the determined values, at a statistical confidence level of 95%; recovery tests were performed for real samples, resulting in recoveries ranging from 90 to 105%. Detection limits of 0.03 and 90 µg g^{− 1} for Cd and Fe, respectively, have been obtained, which are adequate for the purpose.     

Real-time on-line ultrasonic monitoring for bubbles in ceramic ‘slip’ in pottery pipelines

When casting ceramic items in potteries, liquid ‘slip’ is passed from a settling tank, through overhead pipelines, before being pumped manually into the moulds. It is not uncommon for bubbles to be introduced into the slip as it passes through the complex piping network, and indeed the presence of bubbles is a major source of financial loss to the ceramics industry worldwide. This is because the bubbles almost always remain undetected until after the ceramic items have been fired in a kiln, during which process bubbles expand and create unwanted holes in the pottery. Since there it is usually an interval of several hours between the injection of the slip into the moulds, and the inspection of the items after firing, such bubble generation goes undetected on the production line during the manufacture of hundreds or even thousands of ceramic units. Not only does this mean hours of wasted staff time, power consumption and production line time: the raw material which makes up these faulty items cannot even be recycled, as fired ceramic cannot be converted back into slip.Currently, the state-of-the-art method for detecting bubbles in the opaque ceramic slip is slow and invasive, can only be used off-line, and requires expertise which is rarely available. This paper describes the invention, engineering and in-factory testing across Europe of an ultrasonic system for real-time monitoring for the presence of bubbles in casting slip. It interprets changes in the scattering statistics accompanying the presence of the bubbles, the latter being detected through perturbations in the received signal when a narrow-band ultrasonic probing wave is transmitted through the slip. The device can be bolted onto the outside of the pipeline, or used in-line. It is automated, and requires no special expertise. The acoustic problems which had to be solved were severe, and included making the system capable of monitoring the slip regardless of the material of pipe (plastic, steel, etc.) and nature of the slip (which can be very variable). It must also be capable of detecting bubbles amongst the myriad solid particles and other species present in the flowing slip. The completed prototype was tested around several factories in Europe, and proved not only to be more versatile, but also more sensitive, than the state-of-the-art method.     

Determination of arsenic, lead, selenium and tin in sediments by slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry using Ru as permanent modifier and NaCl as a carrier

A procedure for the determination of As, Pb, Se and Sn in sediment slurries by electrothermal vaporization inductively coupled plasma mass spectrometry is proposed. The slurry, 1 mg ml⁻¹, is prepared by mixing the sample ground to a particle size 50 μm with 5% v/v nitric and 1% v/v hydrofluoric acids in an ultrasonic bath. The slurry was homogenized with a constant flow of argon in the autosampler cup, just before transferring an aliquot to the graphite furnace. The tube was treated with Ru as a permanent modifier, and an optimized mass of 1 μg of NaCl was added as a physical carrier. The pyrolysis temperature was optimized through pyrolysis curves, and a compromised temperature of 800 °C was used; the vaporization temperature was 2300 °C. The effect of different acid concentrations in the slurry on the analyte signal intensities was also evaluated. The accuracy of the method was assured by the analysis of certified reference sediments MESS-2, PACS-2 and HISS-1 from the National Research Council Canada, SRM 2704 and SRM 1646a from the National Institute of Standards and Technology and RS-4 from a round robin test, using external calibration with aqueous standards prepared in the same medium as the slurries. The obtained concentrations were in agreement with the certified values according to the Student's t-test for a confidence level of 95%. The detection limits in the samples were: 0.17 μg g⁻¹ for As; 0.3 μg g⁻¹ for Pb; 0.05 μg g⁻¹ for Se and 0.28 μg g⁻¹ for Sn. The precision found for the different sediment samples, expressed as R.S.D. was 1–8% for As, 2–9% for Pb, 6–12% for Se and 3–8% for Sn (n=5).     

Fast multi-element screening of non-digested biological materials by slurry introduction to ICP-AES

A fast method for direct multi-element analysis of non-digested biological samples is presented. The only sample preparation needed is 1 min homogenization with a Polytron mixer in a small volume of neutral phosphate buffer saline solution (PBS). The total time for analysis (sample preparation and measurement) is 4 min only. This “mix and measure” method can handle large sample loads of biological samples and thus minimize dilution of trace elements. For example 100% whole blood was introduced without any clogging of the introduction system or extinguishing of the plasma. In 70% (v/v) whole blood reference material 14 of 16 analytes were quantified within ±10% (Al, B, Ba, Ca, Cu, Fe, Mg, Mn, P, Pb, S, Sr, Ti and Zn) and two semi-quantified within ±20% (Cd and K). Fresh bovine liver was also analyzed with the same method and 7 of 9 analytes were quantified in 5% (w/v) liver slurry. Three different nebulizers were tested, Glass Expansion Concentric (GEC) of Meinhard type, Cross Flow and Burgener T2100 and they performed roughly equally well in giving quantitative results for the slurries but the sensitivity was better with the GEC. The stability of the plasma was studied by evaluating the ratio of Mg 280.270 nm and Mg 285.213 nm lines. When increasing the sample load from 20 to 100% (v/v) of whole blood and from 0.5 to 10% (w/v) of bovine liver the Mg ratio was constant within a few percent for all of the nebulizer tested. The ratio of the sensitivity between GEC and Burgener T2100 was studied and the ratio increased with the energy sum for atomic and ionic lines separately.     

Comparison of action of mixed permanent chemical modifiers for cadmium and lead determination in sediments and soils by slurry sampling graphite furnace atomic absorption spectrometry

Slurry sampling atomic absorption spectrometry with electrothermal atomization was used to the determination of cadmium (Cd) and lead (Pb) in soils and sediments using permanent modifiers. Comparison of action of mixed permanent modifiers niobium (Nb)/iridium (Ir) and tungsten (W)/iridium (Ir) were studied in detail. The effect of amount of Ir, W and Nb on analytical signals of Cd and Pb was examined. The optimal amounts of modifiers for Cd and Pb determination were stated. Niobium carbide formation on graphite surface was studied for different pyrolysis temperatures. Finally for Cd determination in sediments and soils 200 μg of Nb mixed with 5 μg of Ir was used as permanent modifiers and 15 μg of Nb mixed with 200 μg of Ir for Pb determination. Suspensions were prepared in 5% HNO₃. The analytical procedure was optimized carefully basing on data from pyrolysis and atomization curves studies. Ammonium dihydrogen phosphate was used additionally as matrix modifier during Cd determination in samples in order to prevent interferences coming from matrix components. The analysis of CRMs confirmed the reliability of the proposed approach. The precision and accuracy of Cd and Pb determination by the described method for soils and sediments were acceptable.     

Analysis of minimum specific energy consumption and optimal transport concentration of slurry pipeline transport systems

Slurry pipeline transport is widely used in several industrial processes. Calculating the specific power consumption (SPC) and determining the best working conditions are important for the design and operation of transportation systems. Based on the Shanghai Jiao Tong University high-concentration multi-sized slurry pressure drop (SJTU-HMSPD) pipeline-resistance-calculation model, the SJTU-SPC model for calculating the power required to transport a unit volume of solid materials over a unit pipeline length is established for a slurry transport system. The said system demonstrates a uniformity coefficient in the 1.26–7.98 range, median particle size of 0.075–4 mm, particle volume concentration of 10–60%, and pipeline diameter of 0.203–0.8 m. The results obtained were successfully verified against existing experimental data. The influence of parameters, such as particle-gradation uniformity coefficient, median particle size, pipe diameter, and particle volume concentration, on the SPC were analysed. The results revealed that the greater is the uniformity coefficient, the smaller is the minimum specific energy consumption and the larger the optimal transport concentration for a constant, median particle size slurry. As observed, the optimal transport concentration for broad-graded sand equalled approximately 48%. These results supplement the conclusions of existing research, indicating that the optimal transport concentration is approximately 30% and provides theoretical support for high concentration transportation of broad graded slurry.     

锆对低温液相合成甲醇Cu-Cr催化剂性能的影响

用络合共沉淀法制备了Cu Cr和Cu Cr Zr低温液相合成甲醇催化剂,其比表面积分别达到了77. 9和113. 2m2 /g.在5. 5MPa、383和423K的条件下,用间歇式反应釜考察了催化剂的活性和选择性,并用化学分析的方法测定了反应后溶液中钠化合物含量的变化.结果表明, Cu Cr Zr的活性明显高于Cu Cr,其甲醇的选择性则略有下降;同时,由反应后的钠化合物分析发现, Cu Cr Zr催化体系在423K反应后,溶液中甲酸钠的浓度降低,导致催化体系失活的甲醇钠转化为甲酸钠的反应被彻底抑制.     

交联羧甲基淀粉预富集-悬浮体进样-石墨炉原子吸收法测定水样中铬(Ⅲ)和铬(Ⅵ)

以交联羧甲基淀粉(CCMS)为吸附剂,悬浮体进样-石墨炉原子吸收法(GFAAS)测定环境水样中Cr(Ⅲ)和Cr(Ⅵ)形态。研究了溶液pH值、吸附时间、溶液体积、共存离子等对CCMS吸附Cr(Ⅲ)和Cr(Ⅵ)的影响。结果表明:在pH=6.0时,吸附15 min,CCMS可以选择性地吸附Cr(Ⅲ),对Cr(Ⅵ)不吸附,从而实现Cr(Ⅲ)和Cr(Ⅵ)的分离。将吸附Cr?的CCMS加0.1%的琼脂制成悬浮体直接进石墨炉检测,用1 mL 1%盐酸羟胺将Cr(Ⅲ)还原成Cr(Ⅵ),测总铬。方法对Cr(Ⅲ)的检出限为0.044μg/L,相对标准偏差(RSD)为10.4%(初始浓度CCr(Ⅲ)=1.0μg/L,n=11),富集倍数为50倍。将本方法应用于环境标准样品的测定,测得结果与标准值相符。