弧形调强放射治疗对剂量计算方法的要求

在弧形调强放射治疗的治疗计划设计中, 由于包含有很多照射方向, 调强最优化的射束元矩阵计算需要很大的计算量和存储量, 为提高计算效率常使用简化剂量计算模型计算射束元矩阵, 因此有必要研究简化模型对治疗计划质量产生影响。 对一个模拟例子和一个临床实例, 使用没考虑散射效应的原射线剂量计算模型计算射束元矩阵, 由此进行最优化计算。 在得到最优化强度分布后, 通过比较原射线剂量计算模型和微分卷积剂量计算模型得到的剂量分布, 研究了不同射束数目条件下, 使用简化剂量计算模型计算射束元剂量矩阵对最终的剂量分布质量的影响。 结果表明, 在射线束很多的情况下(对应弧形调强照射）, 用简化的剂量计算模型, 即不考虑散射来计算射束元剂量矩阵, 会导致靶区剂量分布的质量大大低于预期的剂量分布质量, 因此, 弧形调强放射治疗的最优化计算中, 有效考虑散射的影响是必要的。 In the treatment planning for arc intensity modulated radiation therapy, because many irradiation directions are involved, the computing time and storage space needed for calculating beamlet dose matrices in optimization is quite heavy. In order to improve the computation efficiency, the simplified dose calculation is often used for the calculation of the dose matrices. Thus, it is deserved to study how this simplification could influence the quality of the treatment plan. In this paper, a simulation and a clinical case are adopted. Using the primary dose calculation model without taking into account the scattering effect to generate the dose matrices of beamlets, the optimization for beam intensity profile are firstly carried out. Then, based on the obtained intensity profile, the dose distributions are recalculated by using the primary dose calculation model and the differential convolution superposition dose calculation model which is more accurate but more time consuming. By comparing dose distributions obtained by this two models, the influence of using simplified model for dose matrix calculation on beam profile optimization is studied. The results demonstrate that when the beam number is large(corresponding to the arc modulated radiation), using the simplified model for the calculation of dose matrix of beamlets will reduce the quality of dose distribution greatly comparing with the expected dose distribution quality. Thus it is very necessary to correctly take into account the scattering effect in beam profile optimization for the arc intensity modulated radiation therapy.     

基于啁啾脉冲干涉仪的高精度定位方案设计分析

提出利用啁啾脉冲干涉仪进行高精度空间定位的新方案,该方案利用2个具有强的经典频率关联的正负啁啾脉冲,入射到分束器后经和频晶体产生和频干涉信号,通过探测所得干涉信号精确确定经过不同路径的2个光信号的相对延迟时间,从而精确确定目标位置,实现高精度定位,理论上可以达到微米量级的定位精度。研究正负啁啾脉冲不完全对称即正负啁啾系数大小的差异对定位结果的影响。结果表明:正负啁啾系数大小的差异对定位结果影响很小,定位结果对这种差异有很强的容忍度。该方案除具有量子定位中HOM(Hong-Ou-Mandel)干涉仪的所有优点外,还具有装置简单,抑制损耗等优点。     

Influences of surface effects and large deformation on the resonant properties of ultrathin silicon nanocantilevers

The purpose of the present work is to quantify the influences of the discrete nature, the surface effects, and the large deformation on the bending resonant properties of long and ultrathin 〈100〉 silicon nanocantilevers. We accomplish this by using an analytical semi-continuum Keating model within the framework of nonlinear, finite deformation kinematics. The semi-continuum model shows that the elastic behaviors of the silicon nanocantilevers are size-dependent and surface-dependent, which agrees well with the molecular dynamics results. It also indicates that the dominant effect on the fundamental resonant frequency shift of the silicon nanocantilever is adsorption-induced surface stress, followed by the discrete nature and surface reconstruction, whereas surface relaxation has the least effect. In particular, it is found that a large deformation tends to increase the nonlinear fundamental frequency of the silicon nanocantilever, depending not only on its size but also on the surface effects. Finally, the resonant frequency shifts due to the adsorption-induced surface stress predicted by the current model are quantitatively compared with those obtained from the experimental measurement and the other existing approach. It is noticed that the length-to-thickness ratio is the key parameter that correlates the deviations in the resonant frequencies predicted from the current model and the empirical formula.     

电子束蒸镀ＭＣＰ超薄防离子反馈膜及膜层特性分析

为了进行ＭＣＰ超薄防离子反馈膜的性能评价研究,并使这种膜层具有良好离子阻挡能力,利用电子束蒸发方法,在微通道板（ＭＣＰ）输入面上制备一种超薄Ａｌ２Ｏ３防离子反馈膜,其膜层厚度为２ ｎｍ时仍连续致密。通过对Ａｌ２Ｏ３防离子反馈膜的电子透过特性测试,给出２ ｎｍ及４ ｎｍ厚防离子反馈膜对应的死区电压分别约为１５０ Ｖ及２００ Ｖ;利用Ｍｏｎｔｅ-Ｃａｒｌｏ法模拟分析了Ａｌ２Ｏ３防离子反馈膜的离子阻挡特性,２ ｎｍ及４ ｎｍ厚Ａｌ２Ｏ３防离子反馈膜对碳离子等的阻挡率分别高于４０％及８６％,另外对有无膜的ＭＣＰ电特性进行测试,可以看出镀２ ｎｍ及４ ｎｍ厚的膜后,ＭＣＰ电子增益分别降低了５１％及８１％。     

静电纺丝制备具有浸润性梯度的聚酰亚胺纳米纤维膜

采用高压静电纺丝技术, 在非对称异型电极上制备得到放射状聚酰亚胺(PI)纳米纤维膜. 采用环境扫描电子显微镜(ESEM)观察了PI膜的微观形貌以及纳米纤维的排列状态; 采用接触角测量仪研究了水滴浸润性的变化; 采用高敏感性力学微电力学天平测量了水滴的黏附力, 分析了微观形貌变化与水滴浸润性质和黏附性质的关系. 结果表明, 该PI纳米纤维膜沿着非对称异型电极三角电极至弧型电极方向纤维排列由密到疏, 呈放射状, 具有独特的微结构梯度; 整个纤维膜上的PI纳米纤维直径均一且具有光滑均匀表面, 纤维与纤维之间的距离约为几微米到几十微米. 由于PI纳米纤维膜所具有的独特的微结构梯度, 致使沿着微结构梯度方向水滴的接触角(从超疏水到疏水)和黏附力(从低黏附到高黏附)均表现出梯度变化的特征.     

溴酚蓝修饰玻碳电极测维生素C中抗坏血酸含量

使用溴酚蓝修饰的玻碳电极,以快速循环伏安法测定维生素C片剂中抗坏血酸含量并优化实验条件.结果表明,溴酚蓝(BPB)修饰玻碳电极用于抗坏血酸含量的分析,有良好的稳定性和抗干扰能力.在0.0050~0.1500 g.L-1浓度范围内,峰电流与浓度呈良好的线性关系,R=-0.9991,检出限为0.0010 g.L-1,结果令人满意.     

利用刚性杆-碟形弹簧模型讨论压杆稳定性

利用刚性杆-碟形弹簧模型讨论了压杆稳定性的非线性问题,并扩展回 归到弹性杆Euler公式. 模型简单,现象直观,可用于教学过程中解释大挠度理论.     

室温合成Cu0.8Ag1.2S和Cu0.5Ag1.5Se纳米晶及X射线光电子能谱表征

X射线光电子能谱;银铜硫三元化合物;银铜硒三元化合物     

DNA FRAGMENTS OF Bombyx mori NUCLEAR POLYHEDROSIS VIRUS CONTAINING THE PROMOTERS ACTIVE IN PROKARYOTES

Using a promoter probe plasmid in E. coli called pHE5, eight different HindⅢ and one SalⅠDNAfragments of Bombyx mori nuclear polyhedrosis virus, directing the expression of the tetracycline re-sistance gene, have been cloned and isolated. The tetracycline resistance levels of the strains containing therecombinant plasmids were measured. Among them, the highest level of the resistance to tetracyclinewas 30μg/ml. Part of the nucleotide sequence of a DNA fragment was determined. A sequence similarto the E. coli promoter was found.