一类半参数回归模型的估计理论

考虑半参数回归模型Y=X’β+g(T)+e,其中(X,T)为取值于R^p×[0,1]上的随机向量,β为p×1未知参数向量,g为定义于[0,1]上的未知函数,e为随机误差,Ee=0,Ee²=σ²>0,且(X,T)与e独立。本文综合最近邻和最小二乘的方法定义了β,g和σ²的估计量,g_n^*和。在适当条件下证明了和的渐近正态性,并得到了g_n^*的最优收敛速度。     

Evolving Networks with Nonlinear Assignment of Weight

We propose a weighted evolving network model in which the underlying topological structure is still driven by the degree according to the preferential attachment rule while the weight assigned to the newly established edges is dependent on the degree in a nonlinear form. By varying the parameter a that controls the function determining the assignment of weight, a wide variety of power-law behaviours of the total weight distributions as well as the diversity of the weight distributions of edges are displayed. Variation of correlation and heterogeneity in the network is illustrated as well.     

Global Parametric Sufficient Optimality Conditions for Semi-infinite Discrete Minmax Fractional Programming Problems Involving Generalized （η,ρ）-invex Functions

In this paper,we discuss a large number of sets of global parametric sufficient optimality condi-tions under various gcneralized (η,ρ)-invexity assumptions for a semi-infinite minmax fractional programmingproblem.     

多发弹丸发射系统阀门电源及可编程发射控制器的研制

多发弹丸发射系统是我院20世纪90年代从俄罗斯引进的设备，用于发射弹丸的快阀门电源属于非标产品，其备件缺乏，维修困难。为保证HL-2A装置弹丸注入实验顺利进行，根据设计要求，研制了这套弹丸快阀电源和可编程发射控制器。它们之间的连接如图1所示。     

精密垫片精冲工艺有限元分析与模具设计

精密垫片零件，如图1所示，零件材料为1Cr18Ni9Ti，强度大（σb=650MPa），有一定塑性。从零件尺寸精度看，φ4mm外圆为IT7级精度，φ4mm外圆与φ2mm内孔有很高的同轴度要求，冲裁断面与零件两端面有垂直度要求，普通冲压不能达到零件精度：从工序的角度看，有冲孔和落料工序，剪切面粗糙度Ra≤3．2μm，属于光洁冲裁范畴；另外，技术条件中要求零件两大面不得有任何划伤，且光滑平整。总体上看，该零件的冲压加工性不好，难度较大，对模具的设计、选材、制造要求都较高。     

CHBr薄膜制备的初步研究

碳氢（cH）及其掺杂材料常被用作ICF实验靶丸烧蚀层材料。制备CH薄膜及其掺杂材料的方法有很多，诸如：离子束辅助沉积、离子溅射沉积、低压等离子体化学气相沉积（LPPCVD）等。近年来，详细研究了LPPCVD法制备CH薄膜的制备方法与工艺，形成了比较成熟的技术路线与工艺路线，并为“神光”实验提供了一系列实验靶丸。     

Electronic Properties of Red P-Type Tl2S5 Single Crystals

Single crystals of red Tl2S5 were prepared by a special modified vertical Bridgman and Stockbarger technique.This growth was performed in our laboratory. The influences of temperature on the electrical conductivity, Hall mobility, carrier concentration, and thermoelectric power (TEP) were carried out in the temperature range 277-413K. Throughout these measurements, various physical parameters such as effective mass of charge carriers,carrier mobility, diffusion coefficient, and the relaxation time for both majority and minority carriers were found.     

SrHfO3和SrTiO3光学特性的第一性原理研究

用全电势线性缀加平面波法(FLAPW)计算了SrTiO3和SrHfO3的光学特性,即介电函数虚部ε2(ω)、光学吸收系数I(ω)和反射率R(ω).对它们光学特性进行了对比分析,给出了它们光学特性的差别,并进行了解释.计算的SrTiO3光学谱分别在4.4,7.4,8.3和23.6eV处出现峰值,且其在4.4eV处的峰值比较高而尖.计算结果与实验值符合得很好.     

Chiral Parameter of Transparent Films Containing Polymer Cholesteric Liquid Crystal-R

The transparent film containing a kind of polymer cholesteric liquid crystal-R was fabricated by the freezing method. The optical polarization response of the film was investigated by a self-manufactured apparatus and its optical rotatory dispersion was measured by a novel technique at the wavelength from 35Onto to 66Onto.At various wavelengths, the chiral parameter of the film has been obtained. The results show that the chiral parameter decreases as the wavelength increases. The maximum and minimum chiral parameters are 0.0343 at the wavelength of 350 nm and 0.0058 at the wavelength of 660 nm, respectively. The obtained data indicate that this kind of polymer cholesteric liquid crystal-R is a promising candidate host material for solid optical chiral waveguides.     

氘氚化锂分解残渣中微量氚的回收

氘作同位素交换气对除氚后的新鲜氘氚化锂残渣[主要成分是硅锂化合物和二氧化硅，渣中含氚约为0．9443mg／g(渣)]中的微量氚进行氚的计量与回收，为氘氚化锂残渣中氚的回收提供技术支持。