Ultrasound induced cleaning of polymeric nanofiltration membranes

Cleaning of the flat sheet nanofiltration membranes, using backflushing, chemical cleaning, and ultrasonication operated individually as well as in combination with chemicals, has been studied in the present work. Identical hydrophilic polyamide membranes were fouled individually using an aqueous solution containing a single dye, an aqueous solution containing a mixture of dyes, and a synthetically prepared petroleum refinery effluent. Effect of different parameters such as the concentration of cleaning solution, contact time, frequency, and power of ultrasound on the efficacy of membrane cleaning has been studied. Optimal cleaning was achieved under sonication conditions of frequency of 24 kHz and power dissipation of 135 W. It was demonstrated that application of sonication under optimum conditions without chemical agents, gave about 85% water flux recovery. In the case of combined chemical and ultrasonic treatment, it was clearly observed that the use of chemical agent increased the efficacy of ultrasonic cleaning. The hybrid method recovered the initial water flux to almost 90% based on the use of 1.0 M aqueous NaOH and 4 min of sonication. Overall, the use of aqueous NaOH in combination with sonication showed a better efficiency for cleaning than the individual processes thus demonstrating a new avenue for membrane cleaning.     

Sonochemical synthesis of graphitic carbon nitrides‐wrapped bimetal oxide nanoparticles hybrid materials and their electrocatalytic activity for xanthine electro-oxidation

A novel network-like magnetic nanoparticle was fabricated on a graphitic carbon nitride through a facile sonochemical route at frequency 20 kHz and power 70 W. To enhance the electrocatalytic activity of the modified materials, the graphitic carbon nitrides (g-C₃N₄) was prepared from melamine. Monitoring of xanthine concentration level in biological fluids is more important for clinical diagnosis and medical applications. As modified CuFe₂O₄/g-C₃N₄ nanocomposite exhibits better electrochemical activity towards the oxidation of xanthine with higher anodic current compared to other modified and unmodified electrode for the detection of xanthine with larger linear range (0.03–695 µM) and lower limit of detection (13.2 nM). To compare with these methods, the electrochemical techniques may be an alternative high sensitive method due to their simplicity and rapid detection time. In addition, the practical feasibility of the sensor was inspected with biological samples, reveals the acceptable recovery of the sensor in real samples.     

Ultrasound-assisted synthesis of 3D flower-like zinc oxide decorated fMWCNTs for sensitive detection of toxic environmental pollutant 4-nitrophenol

Sonochemical synthesis of functionalized multi-walled carbon nanotubes (fMWCNTs) embellished 3D flower-like zinc oxide (ZnO) nanocomposite based novel electrochemical sensor for the detection of toxic environmental pollutant 4-nitrophenol (4-NP) is detailed in this paper. We have used laser-assisted synthesis technique in the development of 3D flower-like ZnO nanoparticles (NPs) and ultrasonication method was employed in preparation of ZnO NPs@fMWCNTs nanocomposite using a high-intensity ultrasonic bath DC200H with power of 200 W/cm² and 40 KHz frequency. The nanocomposite was meticulously fabricated on screen printed carbon electrode (SPCE) to carry out various electrochemical analysis. Different characterizations such as Raman spectroscopy, Fourier transform infrared (FT-IR) spectroscopy, UV visible spectroscopy (UV–Vis), X-ray diffraction (XRD), scanning electron microscopy (SEM), and high-resolution transmission electron microscopy (HRTEM) of the materials used in this work were taken. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) techniques are used in electrochemical investigations. We have observed well-defined oxidation and reduction peak currents representing electrochemical mechanism of 4-NP at very low potentials for ZnO NPs@fMWCNTs/SPCE. Furthermore, we were able to achieve efficient electrochemical determination of 4-NP using the developed sensor with a high sensitivity of 11.44 μA μM⁻¹ cm⁻² and very low detection limit (LOD) of 0.013 μM in a broad linear range of 0.06–100 μM. All the significant features of a good sensor including anti-interference, good stability, excellent repeatability, and reproducibility were exhibited by the sensor. Moreover, we have tested practical feasibility of sensor by carrying out real sample analysis on different water samples.     

Sonochemical-solvothermal synthesis of guanine embedded copper based metal-organic framework (MOF) and its effect on oprD gene expression in clinical and standard strains of Pseudomonas aeruginosa

The guanine incropped Cu based metal-organic framework (Guanine-Cu-MOF) was synthesized by facile one-step sonochemical method by simply mixing of 4-4, biphenyldicarboxylic, guanine and copper nitrate (Bio-Cu-H₂bpdc-Gu). The prepared guanine-MOF was characterized by using X-Ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and Field emission scanning electron microscopy (FE-SEM) techniques. The morphology of prepared material was sponge-shaped which it was well documented, together with the presence of existing functional groups. The effect of prepared material on oprD Gene Expression was investigated in Clinical and Standard Strains of Pseudomonas aeruginosa (PAO-1) and minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) of prepared samples against P. aeruginosa strains were determined through the broth micro-dilution method. The expression of oprD gene in strains affected by Cu-H₂bpdc-Gu was quantitatively investigated through real-time PCR. MIC of Bio-Cu-H₂bpdc-Gu was 400 μg/mL for the standard and clinical strains of P. aeruginosa, while, MBC of this compound was 700 μg/mL for standard strain and 800 μg/mL for clinical strains. The highest and the lowest rate of oprD gene expression were found to be 3.6 and 1.1 fold in the strains, respectively.     

Sonochemical preparation of carbon nanosheets supporting cuprous oxide architecture for high‐performance and non-enzymatic electrochemical sensor in biological samples

Copper (Cu) based metal oxides have high electrocatalytic ability. In this work, we are synthesized stone-like cuprous oxide particles (Cu₂O SNPs) covered on acid functionalized graphene oxide (GOS) sheets using ultrasonic process (50 kHz and 100 W). Besides, the chemical structural and crystalline analyses of Cu₂O SNPs@GOS composites were characterized by transmission electron microscopy, X-ray crystallography and energy-dispersive X-ray spectroscopy. The Cu₂O SNPs@GOS nanomaterials were tested towards detection of 8-hydroxydeoxyguanosine (8-OHdG) in biological samples. As expected Cu₂O SNPs@GOS catalyst modified electrodes performed an outstanding catalytic ability on 8-hydroxydeoxyguanosine oxidation. 8-OHdG is oxidative stress biomarker. Further, it is noted that the detection performance of Cu₂O SNPs@GOS coated electrodes and it’s highly enhanced due to the synergistic effect of Cu₂O SNPs and GOS. Besides, the modified materials provide more electro-active faces and as well as rapid electron transport pathway and shorten diffusion. Moreover, oxidation of 8-OHdG sensor is exploring a long linear or working range of 0.02–1465 µM and high sensitivity (8.75 nM). The viability of the Cu₂O SNPs@GOS proposed electrochemical methods have tested, to find out 8-OHdG concentrations in biological fluids (blood serum and urine) with a satisfying recovery ranges.     

Effects of Na2SO4 or NaCl on sonochemical degradation of phenolic compounds in an aqueous solution under Ar: Positive and negative effects induced by the presence of salts

Sonochemical degradation of 4-chlorophenol, phenol, catechol and resorcinol was studied under Ar at 200 kHz in the absence and presence of Na₂SO₄ or NaCl. The rates of sonochemical degradation in the absence of salts decreased in the order 4-chlorophenol > phenol > catechol > resorcinol and this order was in good agreement with the order of log P (partition coefficient) value of each phenolic compound. The effects of salts on the rates of sonochemical degradation consisted of no effect or slight negative or positive effects. We discussed these unclear results based on two viewpoints: one was based on the changes in pseudo hydrophobicity and/or diffusion behavior of phenolic compounds and the other was based on the changes in solubility of Ar gas. The measured log P value of each phenolic compound slightly increased with increasing salt concentration. In addition, the dynamic surface tension for 4-chlorophenol aqueous solution in the absence and presence of Na₂SO₄ or NaCl suggested that phenolic compounds more easily accumulated at the interface region of bubbles at higher salt concentration. These results indicated that the rates of sonochemical degradation should be enhanced by the addition of salts. On the other hand, the calculated Ar gas solubility was confirmed to decrease with increasing salt concentration. The yield of H₂O₂ formed in the presence of Na₂SO₄ or NaCl decreased with increasing salt concentration. These results suggested that sonochemical efficiency decreased with decreasing gas amount in aqueous solution: a negative effect of salts was observed. Because negative and positive effects were induced simultaneously, we concluded that the effects of salts on the rates of sonochemical degradation of phenolic compounds became unclear. The products formed from sonochemical degradation of 4-chlorophenol were also characterized by HPLC analysis. The formation of phenol and 4-chloro-1,3-dihydroxy benzene was confirmed and these concentrations were affected by the presence of salts.     

Investigation of TiO2 photocatalyst performance for decolorization in the presence of hydrodynamic cavitation as hybrid AOP

In this article, an acoustic cavitation engineered novel approach for the synthesis of TiO₂, cerium and Fe doped TiO₂ nanophotocatalysts is reported. The prepared TiO₂, cerium and Fe doped TiO₂ nanophotocatalysts were characterized by XRD and TEM analysis to evaluate its structure and morphology. Photo catalytic performance of undoped TiO₂ catalyst was investigated for the decolorization of crystal violet dye in aqueous solution at pH of 6.5 in the presence of hydro dynamic cavitation. Effect of catalyst doping with Fe and Ce was also studied for the decolorization of crystal violet dye. The results shows that, 0.8% of Fe-doped TiO₂ exhibits maximum photocatalytic activity in the decolorization study of crystal violet dye due to the presence of Fe in the TiO₂ and it may acts as a fenton reagent. Kinetic studies have also been reported for the hybrid AOP (HAOP) that followed the pseudo first-order reaction kinetics.     

An investigation of the crystallization kinetics of zeotype SAPO-34 crystals synthesized by hydrothermal and sonochemical methods

The kinetics study of SAPO-34 crystallization from a gel containing morpholine as a structure directing agent (SDA) was investigated by means of X-ray diffraction (XRD) patterns in order to determine the kinetics parameters, i.e. induction times, rate constants, frequency factors, and activation energies for the induction and growth stages. The kinetics data of growth period were determined by using the Avrami–Erofeev nucleation growth model. SAPO-34 molecular sieves were synthesized by using both sonochemical-assisted hydrothermal and conventional hydrothermal heating at temperatures of 180, 200, and 220 °C to elucidate the influence of crystallization method on the crystallization kinetics of SAPO-34. The activation energy values indicated that the crystal growth mechanism was enhanced for samples synthesized sonochemically, whereas the induction energy was not greatly affected by using sonication process. Also, the kinetic compensation effect (KCE) was considered in order to obtain the isokinetic temperature.     

Fabrication and characterization of silver/titanium dioxide composite nanoparticles in ethylene glycol with alkaline solution through sonochemical process

This paper aims to study fabrication and characterization of silver/titanium oxide composite nanoparticle through sonochemical process in the presence of ethylene glycol with alkaline solution. By using ultrasonic irradiation of a mixture of silver nitrate, the dispersed TiO₂ nanoparticle in ethylene glycol associated with aqueous solution of sodium oxide yields Ag/TiO₂ composite nanoparticle with shell/core-type geometry. The powder X-ray diffraction (XRD) of the Ag/TiO₂ composites showed additional diffraction peaks corresponding to the face-centered cubic (fcc) structure of silver crystallization phase, apart from the signals from the cores of TiO₂. Transmission electron microscopy (TEM) images of Ag/TiO₂ composites, which average particle size is roughly 80 nm, reveal that the titanium oxide coated by Ag nanoparticle with a grain size of about 2–5 nm. Additionally, the formation of silver nanoparticles on TiO₂ was monitored by ultraviolet visible light spectrophotometer (UV–Vis). As measured the optical absorption spectra of as-synthesized Ag nanoparticle varying with time, the mechanism of surface formatting silver shell on the cores of TiO₂ could be explored by autocatalytic reaction; the conversion of Ag particle from silver ion is 98% for the reaction time of 1000 s; and the activity energy of synthesizing Ag nanoparticles on TiO₂ is 40 kJ/mol at temperature ranging from 5 to 25 °C. Hopefully, this preliminary investigation could be used for mass production of composite nanoparticles assisted by ultrasonic chemistry in the future.     

Sonochemical assisted synthesis of SrFe12O19 nanoparticles

We present the synthesis of M-type strontium hexaferrite by sonochemistry and annealing. The effects of the sonication time and thermal energy on the crystal structure and magnetic properties of the obtained powders are presented. Strontium hexagonal ferrite (SrFe₁₂O₁₉) was successfully prepared by the ultrasonic cavitation (sonochemistry) of a complexed polyol solution of metallic acetates and diethylene glycol. The obtained materials were subsequently annealed at temperatures from 300 to 900 °C. X-ray diffraction analysis shows that the sonochemical process yields an amorphous phase containing Fe³⁺, Fe²⁺ and Sr²⁺ ions. This amorphous phase transforms into an intermediate phase of maghemite (γ-Fe₂O₃) at 300 °C. At 500 °C, the intermediate species is converted to hematite (α-Fe₂O₃) by a topotactic transition. The final product of strontium hexaferrite (SrFe₁₂O₁₉) is generated at 800 °C. The obtained strontium hexaferrite shows a magnetization of 62.3 emu/g, which is consistent with pure hexaferrite obtained by other methods, and a coercivity of 6.25 kOe, which is higher than expected for this hexaferrite. The powder morphology is composed of aggregates of rounded particles with an average particle size of 60 nm.