Polystyrene/magnesium hydroxide nanocomposite particles prepared by surface-initiated in-situ polymerization

In order to avoid their agglomeration and incompatibility with hydrophobic polystyrene substrate, magnesium hydroxide nanoparticles were encapsulated by surface-initiated in-situ polymerization of styrene. The process contained two steps: electrostatic adsorption of initiator and polymerization of monomer on the surface of magnesium hydroxide. It was found that high adsorption ratio in the electrostatic adsorption of initiator could be attained only in acidic region, and the adsorption belonged to typical physical process. Compared to traditional in-situ polymerization, higher grafting ratio was obtained in surface-initiated in-situ polymerization, which can be attributed to weaker steric hindrance. Both Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM) indicated that polystyrene/magnesium hydroxide nanocomposite particles had been successfully prepared by surface-initiated in-situ polymerization. The resulting samples were also analyzed and characterized by means of contact angle testing, dispersibility evaluation and thermogravimetric analysis.     

水中酚的膜萃取分离流动注射技术测定的研究

本文提出了硅橡胶膜在线萃取分离流动注射技术测定水样中苯酚的方法。由于水样中的苯酚透过硅橡胶进入萃取液的萃取量随时间的增加和温度的升高而增大，故采用停流技术及升高温度以降低酚的检出限。     

Preparation of well-defined core-shell particles by Cu2+-mediated graft copolymerization of methyl methacrylate from bovine serum albumin

Small well-defined core-shell poly(methyl methacrylate)-bovine serum albumin (PMMA-BSA) particles have been prepared in a direct one-step graft copolymerization of MMA from BSA at 75 degrees C in water with a trace amount of Cu2+ (5 microM). Initially, BSA generates free radicals and acts as a multifunctional macroinitiator, which leads to the formation of an amphiphilic PMMA-BSA grafting copolymer. Such formed copolymer chains act as a polymeric stabilizer to promote further emulsion polymerization of MMA inside, resulting in surfactant-free stable core-shell particles, confirmed by a transmission electron microscopic (TEM) analysis. The PMMA-BSA copolymers as well as PMMA homopolymer inside the particles were isolated by Soxhlet extraction and characterized by Fourier transform infrared spectroscopy (FT-IR) and thermogravimetry (TG). The highest grafting efficiency was approximately 80%. Effects of the reaction temperature, the MMA/BSA ratio, and the concentrations of Cu2+ and BSA on such core-shell particle formation have been systematically studied. Due to their inert PMMA core and biocompatible BSA shell, these small polymer particles are potentially useful in biomedical applications.     

二维各向同性谐振子的双波描述

二维各同性谐振子体系除哈密顿量外还有三个独立的守恒量。本文给出了对这些不同描术宾比较。     

L—氨基酸氧化酶电极的制作及电极特性的研究

报道了一种新的Ｌ－氨基酸氧化酶电极，这种酶电极系由氨气敏电极和以氨基化玻璃布为载体的酶膜所组成；研究了固定化条件对酶膜活性的影响以及底物浓度、温度和ｐＨ对电极响应特性的影响。该电极在６．０×１０＾－５～４．０×１０＾－３ｍｏｌ／Ｌ的底物浓度范围内呈良好的线性关系，检测下限为５．０×１０＾－５ｍｏｌ／Ｌ。在最宜条件下，酶电极具有良好的稳定性。     

Solidified liquid layer model makes quartz crystal microbalance a convenient molecular ruler

The applications of quartz crystal microbalance (QCM) in biointerfaces are limited by its quantitative ambiguities caused by viscoelasticity and solution effects. Although many studies clearly indicated that the quantitative interpretation of QCM data needed caution, none of those studies provided a practical solution that enabled general and quantitative interpretation of QCM data. Recently we proposed a "solidified liquid layer" model that enabled QCM to be used as a biomolecular ruler. Here we applied five kinds of proteins with significant differences in their sizes and shapes to further validate this model. The effective thickness (T(eff)) of surface immobilized, hydrated proteins were 10.2, 4.7, 1.8 and 4.8 nm for rabbit IgG, streptavidin, lysozyme, and bovine serum albumin, respectively. The critical number of stakes needed for the formation of a solidified liquid layer was found to be protein dependent. We believed this "solidified liquid layer" model will facilitate the popularization of QCM as a valuable tool in biointerface studies, such as protein adsorption process or the conformational change on surface.     

槲皮素伏安行为及其稀土络合物极谱催化氢波研究

在乙醇量小于5％的水溶液中，于pH1.5至4.5，4.2至9.5分别得到槲皮素的两个还原波，均为羰基两电子还原．前者为其分子的强吸附波，后者为一价阴离子的波．在pH6.1附近的醋酸盐缓冲底液中，可获得槲皮素与Tb（Ⅲ）、Dy（Ⅲ）、Ho（Ⅲ）、Er（Ⅲ）、Tm（Ⅲ）、Yb（Ⅲ）、Lu（Ⅲ）和Y（Ⅲ）等重稀土离子络合物的双重表面催化氢波．络合物被诱导吸附，组成为（REL_2）L_吸．Sc（Ⅲ）与槲皮素形成单一表面催化氢波，其组成为（ScL）L_吸．     

Controllable preparation of nanoparticle-coated chitosan microspheres in a co-axial microfluidic device

In this work, we describe a novel and simple microfluidic method for fabricating nanoparticle-coated chitosan microspheres. Uniform droplets of aqueous chitosan solution were dispersed into an oil phase containing partially hydrophilic nanoparticles via a co-axial microfluidic device. Recirculating flow in the continuous phase in the area between drops enhanced mixing and allowed the nanoparticles to coat the surface of the droplets as they passed through the channel. The chitosan droplets were then crosslinked with glutaraldehyde and nanoparticle-coated microspheres were obtained. SEM characterization shows that the microspheres are monodispersed with uniform nanoparticle distribution on the surface. The dispersity, size and composition of the microspheres could all easily be controlled by changing the microfluidic flow parameters and three different types of nanoparticles were successfully used to synthesize hybrid microspheres to demonstrate the method's versatility.     

Traceless synthesis of 3-N-substituted-2-thioxoquinazoline-4-ones on a soluble polymeric support

The synthesis of 3-N-substituted-2-thioxoquinazoline-4-ones is described with a traceless linker strategy using poly(ethylene glycol) (PEG) as a soluble polymeric support. Staudinger-Aza-Wittig reaction of PEG-supported azide with Ph(3)P and CS(2) gave the corresponding PEG-supported phenyl isothiocyanate. Treatment of the phenyl isothiocyanate with different primary amines led, via intramolecular cyclization and simultaneous cleavage from PEG, to 2-thioxoquinazoline-4-ones with of moderate to excellent yields.     

溶剂气浮法去除水中腐殖酸的动力学和热力学初步研究

研究了溶剂气浮法去除水中的腐殖酸,该技术可以作为生物处理后的填埋渗出液的后处理方法。腐殖酸通过与表面活性剂十六烷基三甲基溴化铵生成离子缔合物气浮进入有机溶剂异戊醇而从水中去除。大于计量比的表面活性剂的量在10 m in之内可达92%的去除率。气浮速率在一定程序上随着气流速率的增加而增加,基本上与有机溶剂的体积无关。同时,还考察了电解质、乙醇及溶液的pH值对水中腐殖酸的溶剂气浮过程的影响。研究表明,该溶剂气浮过程遵从一级动力学。气浮过程的表观活化能作为一个特征参数被提出来,其值为2.87 kJ/mol。