PLA/EMAG共混物的制备与表征

通过熔融共混挤出法制备了不同乙烯-丙烯酸甲酯-甲基丙烯酸缩水甘油酯(EMAG)含量下的聚乳酸(PLA)/EMAG共混物,考察共混体系中EMAG与PLA基体之间的相互作用,研究了PLA/EMAG共混物的结晶性能、力学性能、熔体指数、加工性能以及热稳定性.表征结果显示:EMAG中的环氧基团与PLA的端羟基或端羧基发生化学反应,形成反应性共混体系,PLA/EMAG共混物的韧性较纯PLA有大幅提高,在EMAG含量为15;时达到最大.     

双罐式气泵供液制冷系统性能的实验研究

双罐式气泵供液制冷系统作为气泵供液的一种,运用高压气体或液体的压力输送制冷剂到蒸发器。该实验通过控制供液气压来调节再循环蒸发器的供液量,调节制冷系统中的循环倍率,在供液气压升高而导致循环倍率增大的同时,蒸发器的传热量会升高到最大值。通过技术参数的收集整理,分析比较不同工况下的制冷性能、压缩机性能和传热性能等特性,作为双罐式气泵供液制冷系统工程应用的理论依据。实验表明,不同范围的供液压头,对传热性能的主要影响因素不同,蒸发器制冷量在供液压头升高到一定值后不再增加,系统COP也将下降。     

ZnO超细纳米线阵列的制备及其电化学性能

以Zn(NO₃)₂· 6H₂O和C₆H₁₂N₄为原材料,采用二步水热法在碳纤维布上合成了形貌尺寸均匀的ZnO超细纳米线阵列。用 X 射线衍射(XRD)和扫描电镜(SEM)对其晶体结构和形貌进行了表征,利用恒流充放电测试等手段对其进行电化学性能测试。测试结果表明,材料表现出优异的电化学性能。在200 mA/g的电流密度下循环150次后,ZnO超细纳米线阵列仍然约有730 mAh/g的充放电比容量,库伦效率保持在95%以上。在1 200 mA/g的大倍率条件下,材料的充放电比容量依旧可达481 mAh/g左右,表现出十分良好的循环稳定性和可逆性能,是一种较为理想的锂离子电池负极复合材料。     

石英相二氧化硅纳米管的制备及其对Pb2+的吸附行为研究

本文采用纯化的海泡石作为硅源,在不需要模板和煅烧工艺的条件下,制备出了石英相的硅纳米管(SNTs),并对获得样品进行了XRD、FTIR和SEM等表征.制得的SNTs具有40~50 nm外径,管腔直径为10~15 nm,长度为20~100 μm.此外,研究了SNTs对于Pb2+的吸附行为.结果表明,Pb2+吸附量随初始Pb2+浓度,吸附时间,温度和溶液pH值(<5)增加而增加.在溶液pH为5时,SNTs对于Pb2+的吸附平衡的吸附焓(ΔH)和熵变(ΔS)分别为6.28 kJ/mol和69.8 J/mol· K.     

棒状PANI/TiO2纳米复合材料的制备及光催化性能研究

通过共混法和原位氧化聚合法成功制备了棒状聚苯胺/TiO2纳米复合材料,通过SEM、XRD、FT-IR、TGA、TEM、紫外-可见漫反射光谱等测试对其进行表征.并以罗丹明B溶液为模拟污染物,在可见光条件下,棒状PANI/TiO2纳米复合材料的催化降解效率与纯PANI和TiO2相比明显提高.另外,对两种不同方法合成的PANI/TiO2纳米复合材料的光催化性能进行对比,结果表明原位氧化聚合法制得的复合材料,由于TiO2在复合材料中的均匀分布及其与PANI的协同效应,光催化降解率可达91.11;.     

微波法制备CaMoO4:Tb3+,Eu3+白色荧光粉及其发光性能研究

通过微波法制备了CaMoO4:Tb3+,Eu3+白色荧光粉.采用X射线粉末衍射仪、扫描电子显微镜和荧光光谱仪对样品材料的结构、形貌和发光性能进行了表征.分别讨论了在不同助剂、不同反应浓度、不同反应温度及稀土离子Eu3+和Tb3+共掺比例变化对荧光粉的发光性能的影响.结果表明:不加活性剂所得CaMoO4:Tb3+,Eu3+样品在反应浓度为0.06 mol/L、反应温度为120℃时发光性能最好;通过调节CaMoO4:Tb3+,Eu3+荧光粉中稀土离子Eu3+和Tb3+共掺比例荧光粉的发光颜色可以很容易地从冷白光变为暖白光.     

基于NiCo2O4纳米片电极的非对称混合电容器

The looming global energy crisis and ever-increasing energy demands have catalyzed the development of renewable energy storage systems. In this regard, supercapacitors (SCs) have attracted widespread attention because of their advantageous attributes such as high power density, excellent cycle stability, and environmental friendliness. However, SCs exhibit low energy density and it is important to optimize electrode materials to improve the overall performance of these devices. Among the various electrode materials available, spinel nickel cobaltate (NiCo₂O₄) is particularly interesting because of its excellent theoretical capacitance. Based on the understanding that the performances of the electrode materials strongly depend on their morphologies and structures, in this study, we successfully synthesized NiCo₂O₄ nanosheets on Ni foam via a simple hydrothermal route followed by calcination. The structures and morphologies of the as-synthesized products were characterized by X-ray diffraction, scanning electron microscopy, and Brunauer-Emmett-Teller (BET) surface area analysis, and the results showed that they were uniformly distributed on the Ni foam support. The surface chemical states of the elements in the samples were identified by X-ray photoelectron spectroscopy. The as-synthesized NiCo₂O₄ products were then tested as cathode materials for supercapacitors in a traditional three-electrode system. The electrochemical performances of the NiCo₂O₄ electrode materials were studied and the area capacitance was found to be 1.26 C·cm^-2 at a current density of 1 mA·cm^-2. Furthermore, outstanding cycling stability with 97.6% retention of the initial discharge capacitance after 10000 cycles and excellent rate performance (67.5% capacitance retention with the current density from 1 to 14 mA·cm^-2) were achieved. It was found that the Ni foam supporting the NiCo₂O₄ nanosheets increased the conductivity of the electrode materials. However, it is worth noting that the contribution of nickel foam to the areal capacitance of the electrode materials was almost zero during the charge and discharge processes. To further investigate the practical application of the as-synthesized NiCo₂O₄ nanosheets-based electrode, a device was assembled with the as-prepared samples as the positive electrode and active carbon (AC) as the negative electrode. The assembled supercapacitor showed energy densities of 0.14 and 0.09 Wh·cm^-3 at 1.56 and 4.5 W·cm^-3, respectively. Furthermore, it was able to maintain 95% of its initial specific capacitance after 10000 cycles. The excellent electrochemical performance of the NiCo₂O₄ nanosheets could be ascribed to their unique spatial structure composed of interconnected ultrathin nanosheets, which facilitated electron transportation and ion penetration, suggesting their potential applications as electrode materials for high performance supercapacitors. The present synthetic route can be extended to other ternary transition metal oxides/sulfides for future energy storage devices and systems.     

ZCuPb20Sn5合金耐磨性能研究

ZCuPb₂₀Sn₅合金作为柱塞泵转子内衬材料，因其含铅量高，而具有良好的减摩耐磨性能，可避免转子在工作中的磨损失效问题. 选用销盘式摩擦磨损试验机，以ZCuPb₂₀Sn₅和45钢为摩擦副，研究了不同PV值和油润滑条件下，ZCuPb₂₀Sn₅合金的摩擦磨损性能. 结果表明:随着PV值的增加，ZCuPb₂₀Sn₅合金的摩擦系数先增加后减小，而磨损率呈增加趋势. 在载荷50 N和线速度2.410 m/s条件下，摩擦系数和磨损率最低，摩擦系数最低能达到0.010，平均摩擦系数达到1个最低峰值点0.063；在载荷250 N、线速度3.610 m/s以及PV值为126 MPa·m/s的条件下，摩擦系数达到另一低峰值0.070，磨损率为2.972×10?7 mm3/(N·m). PV值最大时，摩擦系数和磨损率最大. 载荷小于150 N时，在油润滑的作用下，主要磨损机制为轻微黏着磨损；载荷大于150 N时，在铅和油的协同作用下，以黏着磨损为主，少量磨粒磨损；当载荷大于250 N时，摩擦系数与磨损率均偏高，以磨粒磨损为主，局部有少量氧化磨损.      

波形钢板-UHPC组合桥面板结构截面优化

对实腹式波形顶板-UHPC(超高性能混凝土)组合桥面板进行了改进, 采用空腹式结构建立波形钢板-UHPC组合桥面板有限元模型, 研究UHPC层厚度、波形钢板厚度、波形长度、下缘板宽度和波形高度等截面参数变化对组合桥面板受力特性的影响, 并确定其合理取值范围. 在此基础上, 通过理想点法对参数组合进行优化, 得到合理的参数匹配. 研究结果表明 相较于实腹式组合桥面板, 优化后的组合桥面板自重减小35%, 钢板弯折处应力减小16%; 相较于正交异性钢桥面板, 桥面板用钢量减小7%, 顶板与U肋连接位置应力减小47%.     

主动射流控制水翼空化的数值模拟与分析

为了改善高速流动工况下水翼吸力面上流场的空化特性,提出了水翼表面主动射流对绕水翼周围流动加以控制的方法.基于密度分域滤波的FBDCM混合湍流模型联合Zwart-Gerber-Belamri空化模型,分析了来流空化数为0.83,来流攻角为8°,射流位置距水翼前缘为x=0.19c时,主动射流对于水翼吸力面上流动的空化特性和水动力特性影响.对回射流的强度进行了量化分析,以探究回射流与流场空化特性的关系.数值分析结果表明,在射流水翼吸力面上的时均空泡体积为原始水翼的1/15,使得流场内空化流动由云空化状态转变为较为稳定的片空化状态,显著地削弱了云空化的发展.此外,射流极大地改善了水翼的水动力性能,使得水翼的升阻比较原始水翼提高了22.9%,空泡的脱落频率减少了26.2%,空泡脱落所引起的振幅减小了9.1%.射流大幅降低了水翼吸力面上低压区面积,水翼吸力面上流体的逆向压力减小,回射流强度降低;同时,射流使水翼吸力面上的边界层减薄,增强了流动的抗逆压梯度能力,一定程度上阻挡了回射流向水翼前缘的流动,这也从机理上分析了主动射流抑制空化的原因.