蒸汽喷射器变工况性能的CFD探讨

利用二维轴对称,真实气体模型对喷射式制冷空调系统的喷射器进行CFD计算。真实气体模型占用较多的计算机资源,但它的计算结果更加真实。计算的目的在于得到在变工况条件下喷射器性能的变化和制冷系统性能的变化情况。在计算范围中,存在一最优的发生压力Pg*(3.973568bar),使得此时的喷射系数和系统COP最大。当Pg>Pg*时,喷射系数和COP随着发生压力的增加而减少;当Pg相似文献   

Comparison of microstructure and mechanical properties of ultra-narrow gap laser and gas-metal-arc welded S960 high strength steel

The microstructural characteristics and mechanical properties, including micro-hardness, tensile properties, three-point bending properties and Charpy impact toughness at different test temperatures of 8 mm thick S960 high strength steel plates were investigated following their joining by multi-pass ultra-narrow gap laser welding (NGLW) and gas metal arc welding (GMAW) techniques. It was found that the microstructure in the fusion zone (FZ) for the ultra-NGLW joint was predominantly martensite mixed with some tempered martensite, while the FZ for the GMAW joint was mainly consisted of ferrite with some martensite. The strength of the ultra-NGLW specimens was comparable to that of the base material (BM), with all welded specimens failed in the BM in the tensile tests. The tensile strength of the GMAW specimens was reduced approximately by 100 MPa when compared with the base material by a broad and soft heat affected zone (HAZ) with failure located in the soft HAZ. Both the ultra-NGLW and GMAW specimens performed well in three-point bending tests. The GMAW joints exhibited better impact toughness than the ultra-NGLW joints.     

不同结构毛细管网辐射板供冷性能实验研究

对两种不同结构毛细管网辐射板的性能进行了实验研究,分析了在不同供水温度下,该两种辐射板在表面温度分布、供冷能力、安装辐射板房间温度变化情况之间的差异,为今后毛细管网辐射供冷空调系统辐射末端的设计应用及运行控制提供依据。     

高性能计算机用热管复合制冷系统设计研究

根据高性能计算机全天候温控的需要,提出了综合应用蒸气压缩和动力型分离式热管制冷技术的复合冷源方案。在冬季及春、秋过渡的低温季节,运行热管循环不仅大幅降低环控装置的能耗,而且可以避免在低温环境运行压缩式制冷易发生的冷启动、回油润滑等问题。提出了蒸气压缩制冷、蒸气压缩/热管复合制冷和热管制冷的分区工作模式,引入复合制冷模式有效拓宽了热管运行温区,大幅提高了制冷系统的综合COP。模拟分析了在北京地区应用热管复合制冷技术的节能性能,相比常规的压缩制冷节能率高达40%。研究表明:热管复合制冷系统具有显著的节能减排优势,特别适用于全天候工作的机房、基站等高热密度电子集成系统的温控。     

室温磁制冷主动式磁蓄冷器数值模拟

提出了一个研究工作参数、设计参数对主动式磁蓄冷器(AMR)制冷性能影响的数值模型。三个主要参数包括:质量流量m、频率f、蓄冷器孔隙率ε,被用来表征AMR的制冷能力。数值模拟的结果表明:对一个AMR而言,存在一个最佳孔隙率;在某一确定孔隙率条件下,AMR存在最佳换热流体质量流量和最佳工作频率;与高频相比,AMR在较低频率下有更好的制冷性能,一味提高频率并不一定能提高AMR的制冷量。模拟结果对磁制冷样机的设计、工作参数的选择有很大的指导意义。     

上海创智311街坊项目冰蓄冷制冷机房系统优化设计

介绍了该工程项目的制冷机房的设计方案,采用冰蓄冷技术结合常规冷水机组的冷源形式,说明了冰蓄冷系统的特点及工况流程,通过分析空调负荷变化规律,分析了不同运行模式的可行性,从而得出优化运行模式,并详述了该运行模式下的具体供冷方案。     

大型回热换热器的降温实验

大型低温配件的降温试验复杂和多变,文中针对大型回热换热器的降温进行了研究。将回热换热器置于特制的冷箱内,利用液氮作为冷源,氦气做为载冷剂为换热器提供降温条件;隔膜压缩机为循环氦气提供循环压力。试验前将换热器上面布置9支传感器,传感器所采集的数据自动记录并保存在上位机内,同时绘制降温曲线,为大型回热换热器的降温研究提供了数据。     

Effect of cooling rate on methane hydrate formation in media

In order to study gas hydrate in media, formation of methane hydrate in three different media including loess, fine and coarse sands were studied. Five cooling rates were applied to form the methane hydrate. The nucleation time of the formation of methane hydrate with each cooling rate were measured for comparison. The experimental results show that the cooling rate is a significant factor affecting nucleation of methane hydrate and gas conversion. Under the same initial conditions, the faster the cooling rate, the shorter the nucleation time and the lower the methane gas conversion rate. The media also affect the formation process of methane hydrate within it. In loess, the gas conversion rate is lowest; in coarse sand, the gas conversion rate is the greatest; and in fine sand, it is in between. According to the study, it is found that the smaller the particle size of the media, the harder the methane hydrate forms within it.     

结晶型聚合物注塑过程冷却模型的数值模拟

对HDPE平板状注塑件的冷却过程进行了数值模拟 .基于小分子结晶性物质的冷却模型 ,建立了固相、液相及固液相界面的控制方程 ,方程中引入热焓E和参数T 后 ,将带耦合条件的热传导方程转变为非线性抛物型方程 ,按控制容积法将其离散后 ,用数学软件Matlab获得了PE的三维温度场 ,这为探讨带相转变的热传导问题提供了一种有效的数值方法 .通过对制件芯层温度变化的模拟值与实验值的比较 ,比较了不同相变温度下理论结果的准确性 ,结果表明 ,在引入一定过冷度后 ,将相变温度定义在低于平衡熔点以下时 ,该方法的模拟值具有更好的准确性 .同时 ,模型分析了不同工艺条件对制件芯层冷却过程的影响 ,通过相变平台出现的先后以及终止时间的不同 ,说明充模温度主要影响熔体阶段的冷却以及相变出现的先后 ,而模具温度主要影响固体阶段的冷却以及相变平台终止的先后 .