Apparent Molar Volume, Heat Capacity, and Conductance of Lithium Bis(trifluoromethylsulfone)imide in Glymes and Other Aprotic Solvents

Lithium bis(trifluoromethylsulfone)imide (LiTFSI) is a promising electrolyte for high-energy lithium batteries due to its high solubility in most solvents and electrochemical stability. To characterize this electrolyte in solution, its conductance and apparent molar volume and heat capacity were measured over a wide range of concentration in glymes, tetraethylsulfamide (TESA), acetonitrile, -butyrolactone, and propylene carbonate at 25°C and were compared with those of LiClO₄ in the same solvents. The glymes or n(ethylene glycol) dimethyl ethers (nEGDME), which have the chemical structure CH₃–O–(CH₂–CH₂–O) _n –CH₃ for n = 1 to 4, are particularly interesting since they are electrochemically stable, have a good redox window, and are analogs of the polyethylene oxides used in polymer-electrolyte batteries. TESA is a good plasticizer for polymer-electrolyte batteries. Whenever required, the following properties of the pure solvents were measured: compressibilities, expansibilities, temperature and pressure dependences of the dielectric constant, acceptor number, and donor number. These data were used in particular to calculate the limiting Debye-Hückel parameters for volumes and heat capacities. The infinite dilution properties of LiTFSI are quite similar to those of other lithium salts. At low concentrations, LiTFSI is strongly associated in the glymes and moderately associated in TESA. At intermediate concentrations, the thermodynamic data suggests that a stable solvate of LiTFSI in EGDME exists in the solution state. At high concentrations, the thermodynamic properties of the two lithium salts approach those of the molten salts. These salts have a reasonably high specific conductivity in most of the solvents. This suggests that the conductance of ions at high concentration in solvents of low dielectric constant is due to a charge transfer process rather than to the migration of free ions.     

Modulated differential scanning calorimetry in the glass transition region

Temperature-modulated calorimetry (TMC) allows the experimental evaluation of the kinetic parameters of the glass transition from quasi-isothermal experiments. In this paper, model calculations based on experimental data are presented for the total and reversing apparent heat capacities on heating and cooling through the glass transition region as a function of heating rate and modulation frequency for the modulated differential scanning calorimeter (MDSC). Amorphous poly(ethylene terephthalate) (PET) is used as the example polymer and a simple first-order kinetics is fitted to the data. The total heat flow carries the hysteresis information (enthalpy relaxation, thermal history) and indications of changes in modulation frequency due to the glass transition. The reversing heat flow permits the assessment of the first and higher harmonics of the apparent heat capacities. The computations are carried out by numerical integrations with up to 5000 steps. Comparisons of the calculations with experiments are possible. As one moves further from equilibrium, i.e. the liquid state, cooperative kinetics must be used to match model and experiment.On leave from Toray Industries, Inc., Otsu, Shiga 520, Japan.This work was supported by the Division of Materials Research, National Science Foundation, Polymers Program, Grant # DMR 90-00520 and the Division of Materials Sciences, Office of Basic Energy Sciences, U. S. Department of Energy at Oak Ridge National Laboratory, managed by Lockheed Martin Energy Research Corp. for the U. S. Department of Energy, under contract number DE-AC05-96OR22464. Support for instrumentation came from TA Instruments, Inc. Research support was also given by ICI Paints, and Toray Industries, Inc.     

A differential scanning calorimetry study on poly(ethylene terephthalate) isothermally crystallized at stepwise temperatures: multiple melting behavior re-investigated

The multiple melting behavior of poly(ethylene terephthalate) (PET) was investigated with differential scanning calorimetry (DSC) by examining PET samples having been subjected to special schemes of crystallization and annealing treatment at multiple descending temperatures. Upon such step-wise annealing in decreasing temperatures, the existence of doublet melting peaks in addition to a series of multiple minor peaks in the PET has been demonstrated using carefully designed thermal schemes. Using the Hoffman theory, multiple lamellae populations, might be suggested to be simultaneously present in the PET subjected to such thermal treatments. However, direct experimental evidence has yet to be provided. The low-temperature minor crystals simply melt during normal scanning without having time enough to reorganize into higher-melt crystals. Nevertheless, the effect of scanning on non-isothermal crystallization does exist but is primarily confined to the temperature range much below the main melting region where the crystallization of polymer chains can progress at a reasonable rate. At higher temperatures near the main melting region, annealing for extended times is required in order to result in relative changes of the melting endotherms of the upper and lower peaks in the main melting doublet. In all we have shown that interpretations of the multiple melting phenomenon in semicrystalline polymers can be better refined.     

Effect of PEG on the crystallization of PPDO/PEG blends

A new biodegradable polymer system, poly(p-dioxanone) (PPDO)/poly(ethylene glycol) (PEG) blend was prepared by a solvent casting method using chloroform as a co-solvent. The PPDO/PEG blends have different weight ratios of 95/5, 90/10, 80/20 and 70/30. Crystallization of homopolymers and blends were investigated by differential scanning calorimetry (DSC) and wide-angle X-ray diffraction (WAXD). When 5% of PEG was blended, the crystallization exothermal peaks (T_c) of PPDO increased sharply and the crystallization exothermal peaks (T_c) of PEG decreased slightly compared with the homopolymers. The crystallization rates of both components increased, and caused greater relative crystallization degree (X_t%). But when the content of PEG was more than 5%, the crystalline behaviors of blends had no more significant changes accordingly. The melting points of each sample varied little over the entire composition range in this study. The nonisothermal crystallization of PPDO homopolymer and blend (PPDO/PEG = 70/30) were also studied by DSC. The crystallization began at a higher temperature when the cooling rates were slower. The nonisothermal crystallization kinetics of blends was analyzed by Ozawa equation. The results showed that the Ozawa equation failed to describe the whole crystallization of the blend, but Mo equation could depict the nonisothermal crystallization perfectly.     

Synthesis and properties of biodegradable elastomeric epoxy modified polyurethanes based on poly(ε-caprolactone) and poly(ethylene glycol)

Biodegradable polyurethane elastomers with potential for applications in medical implants with tunable degradation rate and physical properties were synthesized from reaction of epoxy terminated polyurethanes (EUP) with 1,6-hexamethylene diamine (HMDA) as curing agent. Poly(ε-caprolactone) (PCL) and poly(ethylene glycol) (PEG) as well as 1,6-hexamethylene diisocyanate (HDI) were used for preparation of isocyanate terminated polyurethanes which were subsequently blocked with glycidol to prepare EUPs. All materials were characterized by conventional methods, and their properties were studied fully. Results showed that elastomers based on PEG exhibit superior degradation rate and inferior mechanical properties in comparison to elastomers based on PCL. Optimum degradation rate and mechanical properties were obtained from elastomers made from mixture of PCL and PEG base EUPs.     

Glycol-based sol-gel process for the fabrication of ferroelectric PZT thin films

A new sol-gel system using ethylene glycol was developed for the fabrication of PZT thin films with compositions near the morphotropic phase boundary Pb(Zr_0.52Ti_0.48)O₃. Ethylene glycol was used as both a chelating agent and a solvent to replace the highly toxic methoxyethanol used in previous formulations. Thin films were deposited by spin coating the solutions onto platinized silicon substrates. Films were completely crystallized by about 600°C and contained the ferroelectric perovskite phase. A dielectric constant of about 750–800 at 1 KHz was obtained for thin films of 0.3 µm thickness. The hysteresis measurements revealed a remanent polarization of 15 mC/cm² with a coercive field of 60 kV/cm.     

Effects of different alkali metal ions on the cationization of poly(ethylene glycol)s in matrix-assisted laser desorption/ionization mass spectrometry: a new selectivity parameter

The cationization of poly(ethylene glycol)s, PEG 4000 and PEG 6000, under matrix-assisted laser desorption/ionization conditions was studied by using different concentration ratios of the sodium ion, as the reference ion, and another alkali metal ion (Li(+), K(+), Rb(+), Cs(+)). A linear correlation was found between the intensity ratio of the sodiated PEGs and PEGs cationized with alkali metal ions versus the initial concentration ratio of sodium and alkali metal ions. The slopes of these straight lines are proposed as a novel selectivity ratio for the ionization process. The intensity distribution of the cationized PEGs was also investigated. It was found that the cationized oligomers follow Poisson statistics. The M(n) and M(w) values were also evaluated. An explanation for the observed effects is given.     

PET伸直链结晶体的研究进展

对聚对苯二甲酸乙二醇酯（PET）在特定的结晶条件下是否生成伸直链晶体进行了论证，系统总结了伸直链晶体形成的证据，并讨论了PET伸直链晶体形成的机理。     

双金属氰化物配合物的制备、表征及催化性能

 制备了基于钴氰化锌的双金属氰化物配合物（DMC）催化剂，并\r\n用元素分析、X射线衍射和红外光谱等手段进行了表征，考察了催化剂\r\n的结构与组成对其催化活性的影响以及该催化体系催化环氧烷烃开环聚\r\n合的特点．结果表明，含ZnCl2和叔丁醇的非晶态DMC催化剂具有最高的\r\n催化活性．该催化体系使聚合物的分子量可控，不饱和度很低（＜14μ\r\neq／g），逐步聚合所得到的聚合物的分子量分布较窄（Mn／Mw＜1．4\r\n8）．13CNMR分析结果表明，甲基氧丙环均聚物的链结构具有无规立构\r\n的特点，且链节分布几乎都为头－尾方式．IR分析结果表明，甲基氧丙\r\n环－环氧乙烷共聚物的链结构是无规分布的．