微通道板噪声因子与工作电压关系研究

为了解决微通道板噪声因子的测量问题,提出了一种测量像增强器光电阴极灵敏度和信噪比,从而测量出微通道板噪声因子的方法 .根据该方法,分别在不同阴极电压、微通道板电压以及阳极电压条件下测量了微通道板的噪声因子.测量结果表明,当阴极电压、微通道板电压以及阳极电压分别变化时,微通道板的噪声因子会随之变化.微通道板电压对噪声因子的影响最大,阳极电压的影响最小.微通道板电压每增加100 V,噪声因子大约增加0.11,而阳极电压每增加100 V,噪声因子大约增加3.3×10-4.微通道板工作电压提高,意味着电子碰撞能量提高,同时也意味着二次电子发射系数提高,而根据现有微通道板噪声理论,微通道板的噪声因子会减小,但实测结果却相反.造成这一矛盾的原因是在现有微通道板噪声理论中,仅仅考虑了二次电子发射系数、探测率、电子碰撞几率的因数,而未考虑到电子碰撞能量的因数,因此噪声理论需要进行修正.     

Melt Crystallization of Poly(butylene 2,6-naphthalate)

Poly(butylene 2,6-naphthalate)(PBN)is a crystallizable linear polyester containing a rigid naphthalene unit and flexible methylene spacer in the chemical repeat unit.Polymeric materials made of PBN exhibit excellent anti-abrasion and low friction properties,superior chemical resista nee,and outstanding gas barrier characteristics.Many of the properties rely on the presence of crystals and the formatio n of a semicrystalline morphology.To develop specific crystal structures and morphologies during cooling the melt,precise information about the melt-crystallization process is required.This review article summarizes the current knowledge about the temperature-controlled crystal polymorphism of PBN.At rather low supercooling of the melt,with decreasi ng crystal I izatio n temperature,0'-and a-crystals grow directly from the melt and organize in largely different spherulitic superstructures.Formation of a-crystals at high supercooling may also proceed via intermediate formation of a transient monotropic liquid crystalline structure,then yielding a non-spherulitic semicrystalline morphology.Crystallization of PBN is rather fast since its suppression requires cooling the melt at a rate higher than 6000 K-s_1.For this reason,investigation of the two-step crystallization process at low temperatu res requires application of sophisticated experimental tools.These in elude temperatureresolved X-ray scattering techniques using fast detectors and synchrotron-based X-rays and fast scanning chip calorimetry.Fast scanning chip calorimetry allows freezi ng the transie nt liquid-crystalline structure before its con version into a-crystals,by fast cooling to below its glass transition temperature.Subsequent an alysis using polarized-light optical microscopy reveals its texture and X-ray scatteri ng con firms the smectic arrangement of the mesogens.The combination of a large variety of experimental techniques allows obtaining a complete picture about crystallization of PBN in the entire range of melt-supercoolings down to the glass transition,including quantitative data about the crystallization kinetics,semicrystalline morphologies at the micrometer length scale,as well as nanoscale X-ray structure information.     

以磷化铁为添加剂沿(111)面生长磷掺杂金刚石大单晶

掺杂是调控金刚石性能的一种重要手段。本文采用温度梯度法,在5.6 GPa、1 312 ℃的条件下,选用Fe₃P作为磷源进行磷掺杂金刚石大单晶的合成。金刚石样品的显微光学照片表明,随着Fe₃P添加比例的增加,金刚石晶体的颜色逐渐变深,包裹体数量逐渐增加,晶形由板状转变为塔状直至骸晶。金刚石晶形的变化表明Fe₃P的添加使生长金刚石的V形区向右偏移,这是Fe₃P改变触媒特性的缘故。红外光谱分析表明,Fe₃P的添加使金刚石晶体中氮含量上升,这说明磷的进入诱使氮原子更容易进入金刚石晶格中。激光拉曼光谱测试表明,随着Fe₃P添加比例的增加,所合成的掺磷金刚石的拉曼峰位变化不大,其半峰全宽(FWHM)值变大,这说明磷的进入使得金刚石晶格畸变增加。XPS测试结果显示,随着Fe₃P添加比例的增加,金刚石晶体中磷相对碳的原子百分含量也会增加,这意味着添加Fe₃P所合成的金刚石晶体中有磷存在。     

A multifunctional separator with Mg(OH)2 nanoflake coatings for safe lithium-metal batteries

Dendrite growth and thermal runaway induce serious safety hazards,impeding the practical applications of lithium metal batteries(LMBs).Although extensive advances have been attained in terms of LMB safety,most work only focus on a single aspect at a time.This paper reports a multifunctional separator coated by Mg(OH)2 nanoflakes with various excellent properties including electrolyte wettability,ionic conductivity,Li+ transference number,puncture strength,thermal stability and flame retardance.When used in LMBs,the Mg(OH)2 nanoflake coatings enable uniform Li+ distributing,which makes it homogeneous to deposit lithium,realizing effective dendrite suppression and less volume expansion.Meanwhile,Mg(OH)2 coatings can ensure LMBs are in normal conditions without thermal runaway until 140 ℃.A part of lithium can be converted into Li+ ions by Mg(OH)2 during repeated charge/discharge cycles,not only reducing the risk of separator damage and consequent short circuit,but also replenishing the capacity loss of LMBs.The Mg(OH)2 nanoflakes can coat on all kinds of commercial separators to improve their performances,which offers a facile but effective strategy for fabricating multifunctional separators and a comprehensive insight into enhancing LMB safety.     

2,2-双(4-氯-2-氟苄基)丙二酸二乙酯的晶体结构和密度泛函理论研究

标题化合物是一个重要的精细化工中间体,可用于制备嘧啶类、吡唑类等产品。本文利用红外光谱(IR)、质谱(MS)、核磁共振氢谱(¹H NMR)、核磁共振碳谱(¹³C NMR)和X-射线单晶衍射对此化合物进行了表征,并在B3LYP/6-311G(d, p)模式下使用密度泛函理论(DFT)计算了此化合物的最稳定晶体结构以及最高占有分子轨道(HOMO)和最低占有分子轨道(LUMO)能量。结果表明,通过DFT优化的分子结构与X-射线单晶衍射确定的晶体结构基本一致,该化合物属于单斜方P2(1)/n空间群,晶胞参数为:a=1.563 9(10) nm, b=0.778 6(4) nm, c=1.838 2(10) nm,Z=4, ρ_c＝1.345 g·cm^-3,R=0.047 7,R_w=0.138 7。     

细胞松弛素B阻断微核法鉴定男性个体辐射敏感性的方法初探

初步研究了男性个体辐射敏感性的鉴定方法及标准。采集50名男性志愿者的外周血，分别给予不同剂量X射线照射，采用细胞松弛素B阻断双核法测定微核率(MNF)，通过二阶多项拟合法，绘制微核剂量效应选项中心标准曲线，将个人微核剂量效应曲线与标准曲线比对后判断个体辐射敏感性。 $0.0\sim2.5 $ Gy剂量范围内，剂量效应二阶多项拟合的中心方程为(MNF=0.014 7+0.036 2D+0.023 1D 2， r=0.726)。50名志愿者中，辐射敏感的有13人，辐射抗性的有14人，基本符合正态分布。Spearman秩和相关分析结果显示，MNF在各个辐射剂量点与辐射敏感性均存在正相关,与辐射抗性呈负相关,MNF随剂量增加而增加。本研究初步建立了“以线代点”男性个体辐射敏感性鉴定方法,并发现男性外周血淋巴细胞的本底微核率与个体辐射敏感性呈正相关。     

A multi-directional controllable multi-scroll conservative chaos generator:Modelling,analysis,and FPGA implementation

Combing with the generalized Hamiltonian system theory,by introducing a special form of sinusoidal function,a class of n-dimensional(n=1,2,3)controllable multi-scroll conservative chaos with complicated dynamics is constructed.The dynamics characteristics including bifurcation behavior and coexistence of the system are analyzed in detail,the latter reveals abundant coexisting flows.Furthermore,the proposed system passes the NIST tests and has been implemented physically by FPGA.Compared to the multi-scroll dissipative chaos,the experimental portraits of the proposed system show better ergodicity,which have potential application value in secure communication and image encryption.     

Lamb波频域逆散射全聚焦成像方法研究

Lamb波因其传播距离远、衰减小常被用于板状结构的无损检测中,在基于Lamb波损伤检测的诸多成像技术中,全聚焦方法(Total Focus Method,TFM)方法因其成像分辨率高、信噪比高而受青睐。然而Lamb波的频散效应导致时域延时量不能被准确计算,进而影响传统TFM方法对损伤定位及成像的精度;此外,既有的TFM方法仅以回波幅值作为成像指标,忽略了Lamb波与损伤的相互作用,故而不能通过损伤表面的物理参数增强成像质量。针对这两个问题,本文首先在时域TFM基础上发展了频域TFM,在计算中纳入频散关系以规避频散的影响;其次以包含明确的损伤特征参数--反射率为成像指标,结合频域TFM方法建立损伤逆散射模型,以实现对损伤的准确成像。仿真和实验结果表明:频域逆散射TFM成像方法能够实现对铝板结构中的损伤检测,在工程实践中具有应用价值。     

微氧化烧结制备掺杂Y2O3的SiC陶瓷及含镉模拟废水处理

采用了微氧化烧结制备了不同Y₂O₃质量分数（0%、2%、4%、6%）的多孔SiC陶瓷，通过对陶瓷的晶体结构、微观形貌、物理性能和Cd²⁺的去除率测试发现：添加了Y₂O₃的SiC陶瓷出现了较多的第二相Y₂SiO₇、Y₅Si₃C_0.5，随着Y₂O₃的质量分数增加逐渐升高，主相的衍射峰的强度有降低。扫描电子显微镜测试发现，SiC陶瓷的尺寸在2.5 μm，Y₂O₃引入后，SiC陶瓷的晶粒尺寸降低，高温烧结时液相的含量增加，熔体粘度降低，晶粒结合更加紧密，Y₂O₃的引入提高了多孔陶瓷的体积密度，Y₂O₃质量分数为6%SiC的体积密度最大为2.21 g/cm³。热导率随着Y₂O₃质量分数的增加呈现出先升高后降低的趋势。金属Cd²⁺的过滤测试表明：随着Y₂O₃质量分数增加，Cd²⁺的残留质量浓度、膜通量和去除率先降低后升高，当掺杂质量分数为4%时，Cd²⁺残留质量浓度最低为0.042 mg/L，膜通量达到了最大值572 L/（m²·h），去除率最大为99.95%，相比未掺质量分数杂体系的去除率提高了0.14%。随着溶液pH值的逐渐增大，金属Cd²⁺的残留质量浓度逐渐降低、去除率逐渐升高，pH≥9时最终均趋于稳定。综合来看，多孔SiC陶瓷的助烧剂Y₂O₃最佳掺量为4%。     

肥皂膜过滤器的性能探究

物质分离是很多医疗和工业的核心技术.传统的固体过滤膜可以允许小于临界尺寸的粒子通过而阻挡大的粒子透过.然而，允许大粒子通过而小粒子停留的膜却很难人工制造.Birgitt Boschitsch Stogin、Luke Gockowski等人证明了完全由液体组成的液膜可以被设计成保留小于临界尺寸粒子而透过大尺寸粒子的过滤膜.基于上述研究，本文在液膜过滤器模型基础上进行解析推导，分析讨论了液膜的临界透过条件，并在实验中得到验证.同时，本文通过调节液膜表面张力系数实现了对粒子速度的筛选.