A Hydrogen-Deficient Nickel–Cobalt Double Hydroxide for Photocatalytic Overall Water Splitting

Developing highly efficient and low-cost photocatalysts for overall water splitting has long been a pursuit for converting solar power into clean hydrogen energy. Herein, we demonstrate that a nonstoichiometric nickel–cobalt double hydroxide can achieve overall water splitting by itself upon solar light irradiation, avoiding the consumption of noble-metal co-catalysts. We employed an intensive laser to ablate a NiCo alloy target immersed in alkaline solution, and produced so-called L-NiCo nanosheets with a nonstoichiometric composition and O²⁻/Co³⁺ ions exposed on the surface. The nonstoichiometric composition broadens the band gap, while O²⁻ and Co³⁺ ions boost hydrogen and oxygen evolution, respectively. As such, the photocatalyst achieves a H₂ evolution rate of 1.7 μmol h⁻¹ under AM 1.5G sunlight irradiation and an apparent quantum yield (AQE) of 1.38 % at 380 nm.     

Sulfur-Modified Oxygen Vacancies in Iron–Cobalt Oxide Nanosheets: Enabling Extremely High Activity of the Oxygen Evolution Reaction to Achieve the Industrial Water Splitting Benchmark

The oxygen vacancies of defective iron–cobalt oxide (FeCoO_x-Vo) nanosheets are modified by the homogeneously distributed sulfur (S) atoms. S atoms can not only effectively stabilize oxygen vacancies (Vo), but also form the Co−S coordination with Co active site in the Vo, which can modulate the electronic structure of the active site, enabling FeCoO_x-Vo-S to exhibit much superior OER activity. FeCoO_x-Vo-S exhibits a mass activity of 2440.0 A g⁻¹ at 1.5 V vs. RHE in 1.0 m KOH, 25.4 times higher than that of RuO₂. The Tafel slope is as low as 21.0 mV dec⁻¹, indicative of its excellent charge transfer rate. When FeCoO_x-Vo-S (anode catalyst) is paired with the defective CoP₃/Ni₂P (cathode catalyst) for overall water splitting, current densities of as high as 249.0 mA cm⁻² and 406.0 mA cm⁻² at a cell voltage of 2.0 V and 2.3 V, respectively, can be achieved.     

RuO2修饰纳米多孔Ni-Mo复合电极及其电催化析氢性能

采用脱合金化结合胶体聚沉的方法制备了纳米多孔Ni/RuO_2、Ni-Mo/RuO_2复合电极材料。通过X射线衍射(XRD)、X射线光电子能谱(XPS)、扫描电镜(SEM)、透射电镜(TEM)对电极材料的物相、元素组态、形貌结构、孔径大小和结晶度进行表征,并通过线性扫描伏安、交流阻抗以及循环伏安等方法测试多孔电极的电催化析氢性能。分析结果显示:RuO_2由于聚沉作用包覆在Ni基合金的骨架表面。Mo的加入使Ni-Mo合金非晶化的同时,促使其骨架细化,形成双连续的纳米多孔结构。Mo与RuO_2的加入以及Mo含量的增加均提高了电催化析氢性能。纳米多孔Ni_(2.5)Mo_(2.5)/RuO_2复合电极在50 mA·cm~(-2)的电流密度下析氢过电位为182 mV。     

Enhanced Photoelectrochemical Water Oxidation from CdTe Photoanodes Annealed with CdCl2

Most CdTe photoanodes and photocathodes show positive and negative photocurrent onset potentials for water oxidation and reduction, respectively, and are thus unable to drive photoelectrochemical (PEC) water splitting without external applied biases. Herein, the activity of a CdTe photoanode having an internal p‐n junction during PEC water oxidation was enhanced by applying a CdCl₂ annealing treatment together with surface modifications. The resulting CdTe photoanode generated photocurrents of 1.8 and 5.4 mA cm^?2 at 0.6 and 1.2 V_RHE, respectively, with a photoanodic current onset potential of 0.22 V_RHE under simulated sunlight (AM 1.5G). The CdCl₂ annealing increased the grain sizes and lowered the density of grain boundaries, allowing more efficient charge separation. Consequently, a two‐electrode tandem PEC cell comprising a CdTe‐based photoanode and photocathode split water without any external bias at a solar‐to‐hydrogen conversion efficiency of 0.51 % at the beginning of the reaction.     

Enriched Surface Oxygen Vacancies of Photoanodes by Photoetching with Enhanced Charge Separation

A facile photoetching approach is described that alleviates the negative effects from bulk defects by confining the oxygen vacancy (O_vac) at the surface of BiVO₄ photoanode, by 10‐minute photoetching. This strategy could induce enriched O_vac at the surface of BiVO₄, which avoids the formation of excessive bulk defects. A mechanism is proposed to explain the enhanced charge separation at the BiVO₄ /electrolyte interface, which is supported by density functional theory (DFT) calculations. The optimized BiVO₄ with enriched surface O_vac presents the highest photocurrent among undoped BiVO₄ photoanodes. Upon loading FeOOH/NiOOH cocatalysts, photoetched BiVO₄ photoanode reaches a considerable water oxidation photocurrent of 3.0 mA cm^?2 at 0.6 V vs. reversible hydrogen electrode. An unbiased solar‐to‐hydrogen conversion efficiency of 3.5 % is realized by this BiVO₄ photoanode and a Si photocathode under 1 sun illumination.     

Atomic Layer Deposition of Cobalt Phosphide for Efficient Water Splitting

Transition‐metal phosphides (TMP) prepared by atomic layer deposition (ALD) are reported for the first time. Ultrathin Co‐P films were deposited by using PH₃ plasma as the phosphorus source and an extra H₂ plasma step to remove excess P in the growing films. The optimized ALD process proceeded by self‐limited layer‐by‐layer growth, and the deposited Co‐P films were highly pure and smooth. The Co‐P films deposited via ALD exhibited better electrochemical and photoelectrochemical hydrogen evolution reaction (HER) activities than similar Co‐P films prepared by the traditional post‐phosphorization method. Moreover, the deposition of ultrathin Co‐P films on periodic trenches was demonstrated, which highlights the broad and promising potential application of this ALD process for a conformal coating of TMP films on complex three‐dimensional (3D) architectures.     

Tailoring a Zinc Oxide Nanorod Surface by Adding an Earth-Abundant Cocatalyst for Induced Sunlight Water Oxidation

Herein, a detailed investigation of the surface modification of a zinc oxide (ZnO) nanorod electrode with FeOOH nanoparticles dispersed in glycine was conducted to improve the water oxidation reaction assisted by sunlight. The results were systematically analysed in terms of the general parameters (light absorption, charge separation, and surface for catalysis) that govern the photocurrent density response of metal oxide as photoanode in a photoelectrochemical (PEC) cell. ZnO electrodes surface were modified with different concentration of FeOOH nanoparticles using the spin-coating deposition method, and it was found that 6-layer deposition of glycine-FeOOH nanoparticles is the optimum condition. The glycine plays an important role decreasing the agglomeration of FeOOH nanoparticles over the ZnO electrode surface and increasing the overall performance. Comparing bare ZnO electrodes with the ones modified with glycine-FeOOH nanoparticles an enhanced photocurrent density can be observed from 0.27 to 0.57 mA/cm² at 1.23 V_RHE under sunlight irradiation. The impedance spectroscopy data aid us to conclude that the higher photocurrent density is an effect associated with more efficient surface for chemical reaction instead of electronic improvement. Nevertheless, the charge separation efficiency remains low for this system. The present discovery shows that the combination of glycine-FeOOH nanoparticle is suitable and environmentally-friend cocatalyst to enhance the ZnO nanorod electrode activity for the oxygen evolution reaction assisted by sunlight irradiation.     

Photo-driven water splitting photoelectrochemical cells by tandem organic dye sensitized solar cells with I−/I3− as redox mediator

Dye-sensitized photoelectrochemical tandem cells have shown the promise for light driven hydrogen production from water owing to the low cost,wide absorption spectra in the visible region and ease to process of their constitutive photoelectrode materials.However,most photo-driven water splitting photoelectrochemical cells driven by organic dye sensitized solar cells exhibit unsatisfactory hydrogen evolution rate,primarily attributed to their poor light capturing ability and low photocurrent performance.Here we present the construction of a tandem system consisting of an organic blue-colored S5 sensitizer-based dyesensitized photoelectrochemical cell(DSPEC) wired in series with three spectral-complemental dyes BTA-2,APP-3 and APP-1 sensitizers-based dye-sensitized solar cell(DSC),respectively.The two spectral-complemental chromophores were used in DSC and DSPEC to ensure that the full solar spectrum could be absorbed as much as possible.The results showed that the photocurrent of tandem device was closely related to the open-circuit voltage(Voc) of sensitized DSC,in which the tandem configuration consisting of S5 based DSPEC and BTA-2 based DSC gave the best photocurrent.On this basis,tandem device with the only light energy and no external applied electrical bias was further constructed of BTA-2 based 2-junction DSC and S5 based DSPEC and obtained a photocurrent of 500 μA cm-2 for hydrogen generation.Furthermore,I-/I3-was used as a redox couple between dye regeneration and O2 production on the surface of Pt-IrO2/WO3.The strategy opens up the application of pure organic dyes in DSC/DSPEC tandem device.     

Controlled Synthesis of Cr‐Co0.85Se Nanoarrays for Water Splitting at an Ultralow Cell Voltage of 1.43 V

Water splitting has attracted more and more attention as a promising strategy for the production of clean hydrogen fuel. In this work, a new synthesis strategy was proposed, and Co_0.85Se was synthesized on nickel foam as the main matrix. The doping of appropriate Cr amount into the target of Co_0.85Se and the Cr‐Co_0.85Se resulted in an excellent electrochemical performance. The doping of Cr introduces Cr³⁺ ions which substitute Co²⁺ and Co³⁺ ions in Co_0.85Se, so that the lattice parameters of the main matrix were changed. It is worth noting that the Cr0.15‐Co_0.85Se/NF material exhibits an excellent performance in the oxygen evolution reaction (OER) test. When the current density reaches 50 mA cm^?2 for OER, the overpotential is only 240 mV. For the hydrogen evolution reaction (HER) tests, the overpotential is only 117 mV to drive 10 mA cm^?2 of current density. Moreover, when the Cr0.15‐Co_0.85Se/NF material is used as a two‐electrode device for whole water splitting, the required cell voltage is only 1.43 V to reach a current density of 10 mA cm^?2, which is among the lowest values of the published catalysts up to now. In addition, the Cr0.15‐Co_0.85Se/NF catalyst also exhibits excellent stability during a long period of water splitting. The experimental result demonstrates that the change of the lattice structure has an obvious influence on the electrocatalytic activity of the material. When an external electric field is applied, it facilitates the rapid electron transfer rate and enhances the electrocatalytic performance and stability of the material.