Graphitic nanofillers in PMMA nanocomposites—An investigation of particle size and dispersion and their influence on nanocomposite properties

Mechanical, thermal, and electrical properties of graphite/PMMA composites have been evaluated as functions of particle size and dispersion of the graphitic nanofiller components via the use of three different graphitic nanofillers: “as received graphite” (ARG), “expanded graphite,” (EG) and “graphite nanoplatelets” (GNPs) EG, a graphitic materials with much lower density than ARG, was prepared from ARG flakes via an acid intercalation and thermal expansion. Subsequent sonication of EG in a liquid yielded GNPs as thin stacks of graphitic platelets with thicknesses of ～10 nm. Solution‐based processing was used to prepare PMMA composites with these three fillers. Dynamic mechanical analysis, thermal analysis, and electrical impedance measurements were carried out on the resulting composites, demonstrating that reduced particle size, high surface area, and increased surface roughness can significantly alter the graphite/polymer interface and enhance the mechanical, thermal, and electrical properties of the polymer matrix. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2097–2112, 2007     

Gas solubility of carbon dioxide in poly(lactic acid) at high pressures: Thermal treatment effect

The sorption of carbon dioxide in glassy Poly(lactic acid) (PLA) films was studied by quartz crystal microbalance (QCM) at high pressures. Two thermal treatments, melted and quenched, were performed in PLA with two different L:D contents, 80:20 and 98:2, films and compared with a third thermal protocol, annealed, and used in a previous work. The results obtained show that for pressures higher than 2 MPa, the carbon dioxide solubility is larger in PLA 80:20 than in PLA 98:2, indicating that the L:D plays a dominant role on this property. The thermal treatments only affect the gas solubility in PLA 98:2. Sorption isotherms at temperatures 303, 313, and 323 K, below the glass transition temperature of the polymer, and pressures up to 5 MPa were measured and analyzed with three different models, the dual‐mode sorption model, the Flory–Huggins equation, and a modified dual‐mode sorption model where the Henry's law term was substituted by the Flory–Huggins equation. This last model performs especially well for CO₂ in PLA 80:20, due to the convex upward curvature of the solubility isotherms for that system. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 616–625, 2007     

LD端抽运平直腔Nd:YVO4固态激光器的输出功率特性研究

对LD端抽运平直腔Nd:YVO₄固态激光器输出功率特性受激光器内在诸因素(热透镜效应、腔长、激活孔径等)的制约关系进行了研究.并用传播圆-变换圆图解分析方法给出了合理的解释，同时，对进一步提高其输出功率特性指出了方向. 关键词： 固体激光器 热透镜 变换圆 平直腔     

激光介质的多次吸收不均匀内热源模型

针对激光介质的内热源,以多次吸收作用为基础提出了适用于侧面双向泵浦板状激光介质的不均匀内热源模型,即多次吸收不均匀内热源模型,并与均匀内热源和一次吸收内热源模型进行了对比分析。研究表明,介质厚度及光吸收系数组成的无量纲参数不同时,三种内热源模型得到的内热源分布也有所不同。最后给出了内热源不均匀度及多次吸收模型与一次吸收模型之间的差异在不同目标值下的内热源模型适用准则。     

200MW非再热双抽供热机组变工况计算及工况图的绘制

工况图在热电厂的设计和运行中具有广泛的用途。本文根据引进型双抽非再热200MW供热机组的技术特点，通过编程在纯凝汽工况、单抽工业抽汽工况、单抽采暖抽汽工况和双抽供热等典型变工况计算的基础上，完成了当新蒸汽负荷、工业抽汽负荷和采暖抽汽负荷发生改变时的变工况计算，并绘制了该机组的运行工况图．     

Some applications of thermal field theory to quark-gluon plasma

We briefly introduce the thermal field theory within imaginary time formalism, the hard thermal loop perturbation theory and some of its applications to the physics of the quark-gluon plasma, possibly created in relativistic heavy-ion collisions     

有限长FGM圆筒的热/机应力的解析解

利用微分方程的级数求解方法,分析了两端简支的有限长功能梯度圆筒的轴对称稳态热弹性问题,推导出了稳态温度场与应力场的解析解。分析中采用指数函数模型来描述FGM圆筒中材料性能在厚度方向的连续变化,同时忽略温度对材料性能的影响。另外,论文以金属钼和多铝红柱石制成的功能梯度圆筒为例,给出了稳态温度场和应力场的数值结果。     

<Emphasis Type="Italic">Comment on</Emphasis>¶Low temperature specific heat of blue bronze K <Emphasis Type="Bold">0.30</Emphasis>MoO <Emphasis Type="Bold">3</Emphasis>, by J. Odin,J.C. Lasjaunias,K. Biljaković, K. Hasselbach,and P. Monceau

Eur. Phys. J. B 24, 315 (2001) Here we comment on a recently published paper on the presence of a phason contribution in the low temperature heat capacity data of the charge-density-wave compounds K_0.3MoO₃ and (TaSe₄)₂I. We have shown that the anomaly in the C _P / T ³ data reported by Odin et al. is straightforwardly interpreted in terms of low energy phonon modes resulting from the peculiar topology of these compounds. Received 21 February 2002 Published online 19 July 2002     

Effects of Nb2O5 on thermal stability and optical properties of Er3+-doped tellurite glasses

Er³⁺-doped tellurite glasses with molar compositions of xNb₂O₅-(14.7-x)Na₂O--10ZnO--5K₂O--10GeO₂-- 60TeO₂--0.3Er₂O₃ (x=0, 3, 5, 7 and 9) have been investigated for developing 1.5~μm fibre and planar amplifiers. The effects of Nb₂O₅ on the thermal stability and optical properties of Er³⁺-doped tellurite glasses have been discussed. It is noted that the incorporation of Nb₂O₅ (x=5) increases the thermal stability of tellurite glasses significantly. Er³⁺-doped niobium tellurite glasses exhibit a large stimulated emission cross-section (7.2\times 10^-21- 10.7×10^-21~cm² and the gain bandwidth, FWHM×\sigma_e^{\rm peak} (274\times 10^-28 - 480×10^-28~cm³), which are significantly higher than that of silicate and phosphate glasses. In addition, the intensity of upconversion luminescence of the Er³⁺-doped niobium tellurite glasses decreases rapidly with increasing Nb₂O₅ content. As a result, Er³⁺-doped niobium tellurite glasses might be a potential candidate for developing laser or optical amplifier devices.     

不良导体导热系数测定实验中仪表风扇对实验结果的影响

根据对物体冷却规律的分析,并从实验结果比较,指出稳态法测不良导体导热系数实验中,设置散热盘的冷却过程应与其在稳态过程时的强迫对流散热方式保持一致.