Generation of 3rd and 5th harmonics in a thin superconducting film by temperature oscillations and isothermal nonlinear current response

The generation of harmonics of the voltage response is considered when an AC current is applied through a superconducting film above T_c. It is shown that almost at all temperatures the mechanism of the temperature oscillations created by the AC current and the temperature dependence of the resistance dominates over the isothermal nonlinear electric conductivity. Only in a narrow critical region close to T_c the latter is essential for the generation of the harmonics. A detailed investigation of harmonics generation provides an accurate method for measuring the thermal boundary conductance between the film and the insulating substrate. The critical behaviour of the third harmonic will give a new method for the determination of the lifetime of metastable Cooper pairs above T_c. The comparison of the calculated fifth harmonics of the voltage with the experiment is proposed as an important test for the applicability of the employed theoretical models. Received 8 September 2001     

Mössbauer and X-ray diffraction characterization of Fe60Al40 coatings prepared by thermal spraying

Microstructured (atomized) and nanostructured (milled) Fe₆₀Al₄₀ powders together with their corresponding coatings synthesized by High Velocity Oxy-fuel (HVOF) or Atmospheric Plasma Spray (APS) thermal spraying techniques have been characterized by Mössbauer Spectroscopy (MS) and X-ray Diffraction (XRD). The evolution of the microstructure and the atomic ordering degree in the powders and coatings are discussed at the light of the various processing conditions. The operational correlation between the parameters of the duplex morphology of coatings and the processing parameters is discussed.     

Thermal treatment on composite γ-zirconium phosphate-silica

The prepared amorphous γ-ZrP\SiO₂ composite had a complicated composition, since a part of γ-ZrP is converted to α-form during the exfoliation of it. The γ-ZrP\SiO₂ composite have specific surface area of 421 m²g^–1. The acidic P–OH groups of the lamellae species placed on the surface (it is ≈1.0 meq g^–1), do not destroy until the temperature of 1030 K. During the thermal treatment the total mass loss of 7.79% was found. This value corresponds to 0.42 mole of H₂O per molecule unit. The water loss process was found very slow, because of the placing of bilamellar species in the composite.     

Assessing contaminated hydrogen peroxide for safe storage and transportation using the FTAI

Hydrogen peroxide is a very versatile oxidizing agent, and it is also environmentally compatible considering that the products of its exothermic decomposition are oxygen and water.When kept in a clean temperature-controlled environment, the self-reaction (decomposition) rate is extremely low. However, it is well known that even a small amount of contamination will dramatically increase the reaction rate. This paper describes the use of the fast thermal activity interpreter (FTAI) instrument to examine the chemical reactivity of commercially available 50% hydrogen peroxide at two different temperatures (30 and 40°C) both with and without contamination. The results show that at 30°C a small amount of rust (330 ppm) increases the reaction rate of 50% hydrogen peroxide by a factor of 50. When the temperature is increased to 40°C, the reaction rate is further increased by almost a factor of four. The implication for reactivity management is that at this contamination level most practical vessel sizes would require emergency venting capability. An evaluation was then performed to determine the emergency venting requirement for the safe transportation or storage of the contaminated hydrogen peroxide. It was determined that for quantities of the material less than 5 gallons, conventional breather vents would be sufficient to accommodate the gas evolved. However, for larger quantities, a safety relief device would be needed. For example, for a 400-gallon tote bin at 40°C the required minimum vent area is estimated to be 4.3 in², corresponding to a minimum vent diameter of 2.3 inches.     

Thermal decomposition of a generation 4.5 PAMAM dendrimer platinum drug conjugate

A nanoscale multivalent platinum drug based on a poly(amidoamine) [PAMAM] dendrimer (generation 4.5, carboxylate surface) has been synthesized and fully characterized using a variety of spectroscopic, chromatographic and thermal methods. Treatment of the dendrimer with an aqueous solution containing an excess diaquo(cis-1,2-diaminocyclohexane)platinum(II) produces a conjugate containing approximately forty (diaminocyclohexane)platinum(II) moieties at the surface of the dendrimer. This material undergoes smooth two-stage thermal decomposition to provide residual platinum oxide reflecting the platinum loading in the drug.     

纳米颗粒悬浮液池内泡状沸腾的实验研究

本文对纳米颗粒悬浮液在平壁面上池内沸腾进行了实验研究。实验用的纳米粒子为26 nm的铁粉和13 nm的三氧化二铝纳米粉末,基液为去离子水。分别配成体积浓度为0．1％, 1％和2％的悬浮液。实验结果表明,纳米悬浮颗粒对液体沸腾换热过程的影响会随着纳米颗粒性质,颗粒浓度及热流密度大小的不同而出现不同的效果;加入纳米颗粒后, 对基液沸腾换热的影响存在着两个相反的作用机制,它们分别为:纳米颗粒增强了液体内部的热量迁移能力(热物性的影响)和改变了加热面的表面结构特性(加热面特性的影响)。     

Studies on calcium‐containing poly(urethane ether)s

The calcium salt of mono(hydroxyethoxyethyl)phthalate [Ca(HEEP)₂] was synthesized by the reaction of diethylene glycol, phthalic anhydride, and calcium acetate. Calcium‐containing poly(urethane ether)s (PUEs) were synthesized by the reaction of hexamethylene diisocyanate (HMDI) or tolylene 2,4‐diisocyanate (TDI) with a mixture of Ca(HEEP)₂ and poly(ethylene glycol) (PEG₃₀₀ or PEG₄₀₀) with di‐n‐butyltin dilaurate as a catalyst. A series of calcium‐containing PUEs of different compositions were synthesized with Ca(HEEP)₂/PEG₃₀₀ (or PEG₄₀₀)/diisocyanate (HMDI or TDI) molar ratios of 2:2:4, 3:1:4, and 1:3:4 so that the coating properties of the PUEs could be studied. Blank PUEs without calcium‐containing ionic diols were also prepared by the reaction of PEG₃₀₀ or PEG₄₀₀ with HMDI or TDI. The PUEs were well characterized by Fourier transform infrared, ¹H and ¹³C NMR, solid‐state cross‐polarity/magic‐angle‐spinning ¹³C NMR, viscosity, solubility, and X‐ray diffraction studies. The thermal properties of the polymers were also studied with thermogravimetric analysis and differential scanning calorimetry. The PUEs were applied as top coats on acrylic‐coated leather, and their physicomechanical properties were also studied. The coating properties of PUEs, such as the tensile strength, elongation at break, tear strength, water vapor permeability, flexing endurance, cold crack resistance, abrasion resistance, color fastness, and adhesive strength, were better than the standard values. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2865–2878, 2003     

Effect of Hydrolysis Conditions on the Direct Formation of Nanoparticles of Ceria–Zirconia Solid Solutions from Acidic Aqueous Solutions

The effect of the cation concentration, hydrolysis temperature, and composition in the CeO₂–ZrO₂ system on the direct precipitation of ceria–zirconia solid solutions and the structure of the precipitates from acidic aqueous solutions of (NH₄)₂Ce(NO₃)₆ and ZrOCl₂ by hydrolysis under hydrothermal conditions were investigated. Nanometer-sized (8–10 nm) ceria–zirconia solid solution particles in a composition range of 0 to 60 mol% ZrO₂ were directly precipitated from the solutions with total metal cation concentration less than 0.2 mol/dm³ by simultaneous thermal hydrolysis at 150–240°C. The crystalline phase of the precipitates gradually changed from cubic and/or tetragonal to monoclinic with increasing the cation concentration of the solution from 0.2 to 0.8 mol/dm³ at the starting composition of 50 mol% ZrO₂ under hydrolysis condition of 150°C for 48 h, which was attributed to decrease in the supply of hydrolyzed Ce component caused by decrease in the hydrolysis ratio of (NH₄)₂Ce(NO₃)₆. Ceria–zirconia solid solutions containing large amount of ZrO₂ maintained high specific surface area and small-sized crystallite after heat-treatment at 900–1000°C for 1 h.     

Dynamic mechanical thermal analysis transitions of partially and fully substituted cellulose fatty esters

The main transitions of cellulose fatty esters with different degrees of substitution (DSs) were investigated with dynamic mechanical thermal analysis. Two distinct main relaxations were observed in partially substituted cellulose esters (PSCEs). They were attributed to the glass‐transition temperature and to the chain local motion of the aliphatic substituents. The temperatures of both transitions decreased when DS or the number of carbon atoms (n) of the acyl substituent increased. Conversely, all the transitions of fully substituted cellulose esters occurred within a narrow temperature range, and they did not vary significantly with n. This phenomenon was explained by the formation of a crystalline phase of the fatty substituents. The presence of few residual OH groups in PSCEs was responsible for a large increase in the storage bending modulus, and it eliminated the effect of n on damping. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 281–288, 2003