Anaerobic-anoxic-aerobic sequential degradation of synthetic wastewaters

This study was conducted in a continuous three-stage system of anaerobic (R1)-anoxic(R2)-aerobic (R3) reactors with synthetic wastewater containing phenol (1000 mg/L), chemical oxygen demand (COD) (3000 mg/L), CN⁻ (30 mg/L), SCN⁻(400 mg/L), and NH ₄ ⁺ -N (600 mg/L) as principal pollutants and well-acclimated heterogeneous microbial cultures. The final effluent was partially returned to R2 with a recycle ratio of 1. Anaerobic stage served to detoxify the feed by removing up to 80% of cyanide. Complete SCN⁻ removal and denitrification could be achieved in the anoxic stage by utilizing phenol as an internal source of carbon. Nitrification efficiency of 93% was obtained in the aerobic reactor. The results demonstrated that the three-stage system can give the desired final treated effluent quality (0 mg/L of phenol, 0.2 mg/L of CN⁻, 210 mg/L of COD, and 20 mg/L of NH ₄ ⁺ -N) and that the NO ₃ ⁻ -N concentration can be lowered by a higher recycle ratio.     

Use of a Dual-Marker Form of Analysis to Estimate Binding Constants Between Receptors and Ligands by Affinity Capillary Electrophoresis

This work describes the use of a dual-standard analysis approach termed the time-average ratio (TAR) in affinity capillary electrophoresis (ACE) to estimate binding constants of receptors to ligands. In this form of analysis the TAR is the migration time of the receptor divided by the average of the sum of the migration times of two non-interacting standards. This change in TAR as a function of the concentration of ligand yields a value for the binding constant. This concept is demonstrated using three model systems: carbonic anhydrase B (CAB, EC 4.2.1.1) and arylsulfonamides, vancomycin (Van) and ristocetin (Rist) from Streptomyces orientalis and Nocardia lurida, respectively, and d-Ala- d-Ala terminus peptides. Three ACE techniques are used to examine the three systems: standard ACE, flow-through partial-filling ACE (FTPFACE), and on-column derivatization coupled to ACE. The findings described here demonstrate that ACE data analyzed using the TAR form of analysis yield binding constants between receptors and ligands comparable to those estimated using other ACE forms of analysis. A comparison to three other forms of analysis is described.     

Synthesis,characterization, and application of griseofulvin surface molecularly imprinted polymers as the selective solid phase extraction sorbent in rat plasma samples

In present study, an investigation was carried out to develop and validate an analytical method for the selective extraction and determination of griseofulvin (GSF) from plasma samples. For this purpose, a rational approach was made to synthesize and characterize the surface molecularly imprinted polymers (SMIPs). The SMIPs were utilized as solid phase extraction (SPE) sorbents. The SMIPs were prepared by using GSF as template molecule on the surface of modified silica particles through a non-covalent technique. The particles demonstrated high adsorption capacity (119.1 µg/mL), fast adsorption equilibrium time (30 min) and good recognition selectivity for the template drug. The scanning electron microscopy and infrared spectroscopy were used to explain the structural and morphological characteristics of the SMIPs and surface non-imprinted polymers. The SPE method was combined with HPLC for plasma analysis. The method validation results demonstrated that the established method possessed good linearity for GSF ranging from 0.1 to 50 µg/mL (R² = 0.997). The limit of detection for this method was 0.02 µg/mL for rat plasma samples. The recoveries of GSF from spiked plasma samples were (90.7–97.7%) and relative standard deviations were (0.9–4.5%). Moreover, the SMIPs as selective SPE sorbent can be reused more than 8 times which is a clear advantage over commercial SPE sorbents. Finally, the usefulness of the proposed strategy was assessed by extraction and detection of GSF in real rat plasma samples.     

用电子散斑干涉法测量材料热膨胀系数

 利用双光束电子散斑干涉法（ESPI）对试件受热变形进行了实时观测，针对一次实验过程中得到的图片较多（300～500幅）的特点，在图像处理时摒弃了以往的手动识别等位移线的办法，用MATLAB语言编写了批处理程序，能够在采集的大量散斑图片中自动快速准确地标定等位移线，得到相应的位移和应变，并结合实时测量的温度值，获得了45钢和LY12铝合金在不同温升率下的热膨胀系数及其随温度的变化。实验结果表明，在涉及的温升率范围内，温升率的改变对材料热膨胀系数的影响不明显，材料的热膨胀系数随温度的升高略有上升。     

FTO客体3m闪光照相的Monte Carlo研究

 研究了客体模型FTO的闪光照相系统X光输运过程，给出了直穿照射量、散射照射量、直散比、直穿照射量能谱、散射照射量能谱、直穿X光通量能谱和散射X光通量能谱在记录平面的空间分布。结果表明：后锥是照射量散射成分的主要来源，后锥照射量占总散射量97%；后锥也是造成散射的空间分布不均匀的主要器件，这一不均匀性高达58%。照相系统的最小直散比非常小，表明锥造成的散射已经严重地淹没了直穿（轫致辐射）信号。计算中使用高空间分辨率记录法进行分点，合成图像对吸收系数的复原结果与国外报道的结果相符。     

微波大气吸收衰减特性分析及分层数值算法

 给出了微波在大气中传输受气体分子吸收导致衰减的较精确计算模型，该模型扩展了传统计算模式忽略温度、湿度、压力变化及传播距离受限制的近似算法。结合我国某地区的实测气象数据模拟计算了该地区的大气吸收衰减，最后根据数值计算结果分析了微波随频率、发射角度以及月份（季度）变化的传播特性，并简要说明了此研究在微波遥感中的实际意义。     

退火温度对KDP晶体光学均匀性的影响研究

 研究了磷酸二氢钾（KDP）晶体热退火前后光学均匀性的变化，发现适当温度下退火可以降低KDP晶体的内应力，提高晶体的消光比，从而提高晶体的光学均匀性。实验证明，50℃下退火即可消除部分内应力，110℃下退火可以消除生长鬼影和鬼线。但是,退火温度太高（如170℃）,也可能使晶体的均匀性降低。     

大气闪烁对自适应光学校正的影响

 激光在大气湍流中长距离近水平传输时，闪烁加强，限制了常规自适应光学的校正能力。数值研究了大气闪烁对自适应光学校正的影响，拟合得到了在Fresnel数一定时，Strehl比与Rytov方差的表达式，以及Rytov方差一定时，Strehl比与Fresnel数的表达式。结果表明，在Rytov方差较小时，纯相位校正Ｓtrehl比只与Rytov方差有关；随着Rytov方差的增加，Strehl比不仅与Rytov方差有关，还与Fresnel数有关，Fresnel数越大，校正Strehl比越大；大发射和接收孔径有利于提高校正Strehl比；在一定的Rytov方差下，Stregl比随Fresnel数增大而增加，逐步趋于饱和，达到纯相位校正的极限。     

Kinetic energy decomposition scheme based on information theory

We proposed a novel kinetic energy decomposition analysis based on information theory. Since the Hirshfeld partitioning for electron densities can be formulated in terms of Kullback–Leibler information deficiency in information theory, a similar partitioning for kinetic energy densities was newly proposed. The numerical assessments confirm that the current kinetic energy decomposition scheme provides reasonable chemical pictures for ionic and covalent molecules, and can also estimate atomic energies using a correction with viral ratios.     

Effect of external pressure on the Kβ/Kα X-ray intensity ratios of 3d metals

The occupation numbers of the 3d transition metals are calculated as a function of pressure by means of the linear muffin-tin-orbital method. This data is used with the multiconfiguration Dirac-Fock (MCDF) X-ray intensity ratios (R) to estimate the variation of the intensity ratios of 3d metals with pressure. It is found that R decreases with pressure for the early 3d metals whereas it increases for the heavier 3d transition metals.