PEMFC阴极中氧扩散和电化学反应模型研究—I．TFFA模型及其数值计算

将薄膜浸渍聚集体（TFFA）模型用于描述质子交换膜燃料电池（PEMFC）阴极中氧的扩散和反应过程，其中包括氧气在气体扩散层和反应层气体通道中的扩散，氧气在反应层薄膜中的溶解和扩散，氧在反应层浸渍聚休体中的扩散和反应以及电子和离子的传导，并根据PEMFC阴极的结构特点给出TFFA模型的数值解法。     

熔融浸渍法制备锂离子电池正极材料LiMn2O4的研究

采用LiNO3和MnO2为原料,在650℃下制备了尖晶石型的LiMn2O4.通过X射线衍射、扫描电子显微镜、热重分析和电化学性能测试,发现该化合物具有很高的放电比容量和较好的循环性能,首次放电比容量可达到122 mA·h/g.并对循环性能衰减的各种因素进行了讨论.     

Effect of BaBiO3 and Ba0.6K0.4BiO3 additives on the rechargeability of manganese oxide cathodes in alkaline cells

The effect of the incorporation of small amounts (1–5 wt%) of semiconducting BaBiO₃ and metallic Ba_0.6K_0.4BiO₃ additives on the rechargeability of electrolytic manganese dioxide (EMD) cathodes in alkaline cells in the one-electron regime has been investigated. Both the BaBiO₃ and Ba_0.6K_0.4BiO₃ additives lead to better cyclability compared to the previously known binary oxide additive Bi₂O₃. X-ray diffraction patterns recorded before and after 30 cycles as well as cyclic voltammograms recorded after first and 30 cycles reveal that the better cyclability in the presence of BaBiO₃ and Ba_0.6K_0.4BiO₃ additives is due to the suppression of the formation of unwanted, electrochemically inactive birnessite and hausmannite phases and a shifting of the second-electron capacity of Mn to higher potentials.     

Modeling Studies of the Formation and Destruction of NO in Pulsed Barrier Discharges in Nitrogen and Air

This paper presents the results of modeling studies on the formation and destruction of NO in pulsed barrier discharges in nitrogen and air. The goals of this work are to identify the major processes involved in the formation and destruction of NO in air discharges, to distinguish between oxidative and reductive paths for NO destruction, to explore the potential importance of excited state reactions, to evaluate the role of water in such systems, and to identify the final products in the absence of heterogeneous processes. In all cases, the systems were modeled with 100×10^–4% (100 ppm) of added NO, with and without 3% added water. The focus in all of this work is chemistry in the post-pulse regime.     

阴极支撑型固体氧化物燃料电池的制备与测试

采用固相反应法合成A缺位的(La_0.8Sr_0.2)_0.95MnO₃(LSM95)作为阴极材料,Zr_0.9Sc_0.1SO_1.95(SSZ)商业粉体作为电解质材料,溶胶-凝胶法合成的La_0.8Sr_0.2Cr_0.5Mn_0.5O₃-(LSCrM)作为阳极电催化材料,利用流延、共烧结及浸渍法得到结构为LSCrM-CeO₂|SSZ|3YSZ-LSM95的阴极支撑型固体氧化物燃料电池,分别在氢气气氛和甲烷气氛中进行电化学性能测试. 结果表明,浸渍0.11 g·cm ^-2 CeO₂的LSCrM-CeO₂|SSZ|3YSZ-LSM95单电池在以CH₄为燃料时,600、650、700、750和800 ^oC下的功率密度分别为1.68、4.70、12.40、28.08和54.78 mW·cm ^-2,表现出一定的电化学性能和较好的稳定性.     

火花激发原子发射光谱分析不锈钢线材

火花激发原子发射光谱法应用于直径小于8mm的不锈钢线材的分析，对此类试样应用了一种特制的夹具，用块状标准样品制作工作曲线。由于线状试样和块状标准样品之间的形状差异所产生的系统不确定度借采用同类型标样作校正，对共存元素的相互干扰也采用了相应的校正方法。其它分析条件，包括严格的制样工序，氩气的纯度要求及其流量控制，以及光源的最佳条件等，作了深入的试验。按所提出的方法测定了不锈钢线材试样中碳、硅、锰、磷、硫、铬、镍及钛等8个元素。经校正后的结果与化学法测得结果相符。     

Concentrations of Active Species in the Flowing Afterglow of a Nitrogen Microwave Plasma

Measurements of nitrogen atom density, by means of NO chemical titration, along with an evaluation of the densities of some excited species N ₂ (B, v=11), N ₂ (B, v=2), N ₂ (C, v=0), and N ₂ ⁺ (B,v=0), by means of a spectroscopic study of some bands of dinitrogen, are achieved along the flowing afterglow of a dinitrogen microwave plasma (2450 MHz) for several pressures. The concentrations obtained are in the following range: [N]10 ⁺¹⁵ , [N ₂ (B, 2)]10 ⁺⁹ –10 ⁺¹⁰ , [N ₂ (B, 11)]10 ⁺⁸ –10 ⁺⁹ , [N ₂ (C, 0)]10 ⁺⁶ –10 ⁺⁷ , [N ₂ ⁺ (B,0)]10 ⁺⁶ -10 ⁺⁸ (cm^-3). From a kinetic study of the formation and decay of excited and charged species, an estimation of N ₂ (A, v), N ₂ (X, v, and N ₂ ⁺ (X) densities can be derived: [N ₂ (A, v)]10 ⁺¹² , [N ₂ (X, v6)]10 ⁺¹⁵ –10 ⁺¹⁶ , [N ₂ (X, v12)]10 ⁺¹⁴ –10 ⁺¹⁵ , [N ₂ ⁺ (X)]10 ⁺¹⁰ (cm ^-3 ).     

微乳液法合成LiFePO4 / C正极材料及其电化学性能

本文采用微乳液方法合成了纳米LiFePO₄ / C正极材料。制备样品分别用XRD和SEM进行表征，充放电测试其电化学性能。600 ℃制备样品为单一物相，平均粒径90 nm，在室温2.0～4.0 V (vs Li) 放电电压范围和15 mA·g^-1放电速率下，首次放电容量达到159 mAh·g^-1。制备样品同样展现良好的循环性能。在15 mA·g^-1速率下40次循环后，制备样品放电容量仍保持首次放电容量的98.9%。优异的电化学性能得益于样品颗粒的纳米尺寸、均匀分布以及表面碳层包覆提高了活性材料的电子电导率。     

La2O3,Y2O3-Mo次级发射材料研究

采用粉末冶金方法制备了La2O3，Y2O3-Mo次级发射材料，测试了各种材料的次级发射系数。结果表明在钼中加入稀土氧化物可以具有很好的次级发射性能。经过激活处理后，材料的最大次级发射系数均高于2．0，达到了材料使用要求的发射水平。应用扫描电镜(SEM)和光电能谱仪(XPS)研究了稀土元素在烧结体断口和发射前后在试样表面的分布情况。分析结果表明稀土元素易于在晶界处偏聚，且发射后试样表面稀土元素的相对浓度明显高于发射前的浓度。     

Electrochemical characteristics of Ce0.8Gd0.2O1.9|La0.6Sr0.4CoO3-δ + Ce0.8Gd0.2O1.9 half-cell

The analysis of the medium temperature half-cell Ce_0.8Gd_0.2O_1.9|70 wt% La_0.6Sr_0.4CoO_3- (LSCO) + 30 wt % Ce_0.8Gd_0.2O_1.9 (CGO) has been made by electrochemical impedance, cyclic voltammetry and chronoamperometry. The shape of complex impedance plots depends on temperature and cathodic polarisation of the electrode. Nyquist (Z, Z-) plots were fitted by equivalent circuit taking into account the electrolyte properties (at very high frequencies), charge transfer process at grain boundaries (at high frequencies), and medium and low frequency O₂ reduction process at the cathode surface and inside the porous cathode material. Two different time constants have been obtained for the cathode process, i.e. for electroreduction of oxygen. It was found that the addition of CGO into the cathode material (LSCO) only somewhat decreases the surface catalytic activity but the noticeably higher low-frequency resistance (i.e. mainly diffusion-like mass transfer resistance R_D) values at lower temperatures have been calculated. It was found that the mainly bulk diffusion-limited process at T773 K deviates toward the kinetically mixed process (diffusion + charge transfer) with increasing temperature.