氩离子激光器输出光功率稳定度与光反馈应用

通过实验观测氩离子激光器工作电流与输出光功率及其稳定性之间的关系，采用光反馈解决了反馈工作点的设置和跟踪调解，使输出光功率稳定性得到明显提高。     

Filter-radiometer-based realization of candela and establishment of photometric scale at UME

The luminous intensity unit of candela was realized based on filter-radiometer, which is traceable to detector-based primary standard electrical substitution cryogenic radiometer (ESCR). In that realization the traditional Osram Wi41/G-type incandescent lamp and filter-radiometer consisting of an aperture, a V(λ) filter and a silicon photodiode based trap detector were used as light source and detection element, respectively. Measurement techniques of effective aperture area, spectral transmittance of V(λ) filter and absolute responsivity of trap detector are also presented.     

Investigation and optimization of the covering power and coloristic properties of paint coatings of complex composition

A method for finding the optimum sizes of pigment particles, their volume concentration, and the paint coating thickness that provide the covering power and the required coloristic characteristics of reflected light for the minimum flow rate of pigments is based on using a four-flow approximation of the solution to the equation of radiation transfer in dispersion media and is extended to coatings of complex composition. The capabilities of the method are demonstrated by examples of coatings of mixtures of hematite and rutile particles in a binder with n=1.5 for variations of the modal size and the half-width of the size distribution of the pigment particles. B. I. Stepanov Institute of Physics, Academy of Sciences of Belarus, 70, F. Skorina Ave., Minsk, 220072, Belarus. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 90–96, January–February, 1997.     

电站锅炉系统性能仿真模型的建立

1引言根据热力学第二定律，燃料中的化学拥将近一半损失在锅炉的燃烧与传热过程中。因此，优化锅炉性能对降低整个火电机组的煤耗率具有明显效果。完整的锅炉系统由磨煤机、送风机、一次风机、弓讯机、炉膛、汽包、过热器、再热器、省煤器、空气预热器等单元组成，这些单元之间的联结错综复杂。本文建立了锅炉系统中通用单元的性能模型，并在此基础上，对锅炉系统的结构特点进行了分析，利用过程系统工程中的序贯模块法建立了整个锅炉系统的性能模型。对单元的划分、回路的切断及断裂流股的收敛与迭代策略提出了自己的观点。最后根据生产厂…     

花丝内插物强化竖直管内凝结换热的实验研究

1前言大空隙率多孔体管内插物-绕花丝内插物，被认为是强化管内凝结换热的最有效途径之一[1]．但以往的研究，由于实验雷诺数范围较小，蒸汽速度较低，要正确全面评价其性能尚显不够。本文在原有工作的基础上，进一步完善了实验系统，改进了测试手段，扩大了实验雷诺数范围，并测试了其阻力性能，对花丝内插物强化管内凝结换热进行了较深入全面的实验研究，以全面评价花丝内插物对管内凝结换热的强化效果。2实验系统本文实验系统如图1所示。实验段是一个竖直套管冷凝器，如图2所示．本试验研究蒸汽完全凝结时的传热。凝结水流量采用容积法计…     

两个不等式的加强与证明

本文利用幂平均加强了林同坡不等式和Ｓｔｏｌａｒｓｋｙ不等式，并给出了证明．     

不良导体热系数和热体散热率测量方法研究(英文)

本文介绍一种直接测量散热率新方法．进而测出不良导体的热系数。该方法，减小了由间接测量散热率所带来的误差，实验装置简单，操作方便，参数少，测量结果的精确性和重复性都有较大提高，更重要的是这一新的实验方法突出了物理思想。     

Forced-air precooling of spherical foods in bulk: A parametric study

In this paper, a mathematical model for forced-air precooling of spherical food products in bulk is developed. The foods are arranged in horizontal layers stacked one above the other to form a rectangular parallelepiped with a vertical gap in between the product layers. The foods are cooled by chilled air blown along the height of the package. The governing equations for the conduction heat transfer in the foods, simultaneous heat and mass transfer at the food-air interface and in the air stream are solved numerically using finite-difference methods. A comprehensive numerical study is performed by varying the process parameters over a wide range. Typical results showing the variation of moist air properties along the height of the package and the effect of each parameter on the process time are presented. The ranges of parameters for advantageous operation of the precooling system are identified. Correlations are obtained for the process time based on the product center and mass-averaged temperatures in terms of process parameters.     

三维流动传热空隙率计算程序FASTOR—3D开发研究

1引言大粘度（大r）和大系数（ss和sc）法是处理流动区域中障碍物的常用方法山。但当流动区域中障碍物数量较多时，宜采用空隙率来模拟障碍物，如模拟反应堆流动传热的商用程序COMMIX［’］。我们根据空隙率模拟的基本概念，针对采用交错网格的压力校正法，自行编制了多障碍物流动传热三维计算的全部源程序代码，应用于某核反应堆钠池流动传热的数值模拟，获得了比较合理的结果。2数学模型和数值方法2．1控制方程空隙率修整的质量、动量、能量及湍流动能与耗散率的守恒方程通式的三维柱坐标形式为其中中一1，。，。，。，T，k，。分别表…     

非共沸制冷剂R417A在水平光滑管内的沸腾传热

应用一种快速、准确的隐式格式迭代数值计算方法 ,对非共沸制冷剂 R41 7A在水平光滑管内的蒸发过程进行了数值模拟。通过应用纯质的传热公式计算后与实验值相比较 ,数值计算结果高于实验值。