水中氯苯类污染物的顶空液相微萃取 GC-MS法测定

研究了用顶空液相微萃取GC-MS法测定水中的痕量氯苯类有机污染物。通过实验选择正辛醇为萃取剂,考察了萃取剂的体积、萃取温度、萃取时间、搅拌速度、样品顶空体积以及盐效应等对萃取的影响。在最佳萃取和测定条件下,方法的线性范围为0.1~800μg/L,检出限(S/N=3)为0.05~0.1μg/L。用本方法测定了实际样品及回收率,结果满意。     

The impact of flow injection on modern chemical analysis: has it fulfilled our expectations? And where are we going?

Presenting a condensation of the opening lecture of the 12th ICFIA conference, this communication presents a view of the impact that flow injection analysis (FIA) has had on modern analytical chemistry, evaluated both within the academic community and outside it, i.e. in “industry”. The ensuing developments of FIA, encompassing sequential injection analysis (SIA) and bead injection lab-on-valve (BI-LOV), are described and their individual features discussed. Finally, some recent results of the activities from the author’s own research group are briefly mentioned.     

Amperometric detection of hydrazine by cyclic voltammetry and flow injection analysis using ruthenium modified glassy carbon electrodes

Glassy carbon electrodes modified with (5-amino-1,10-phenanthroline)bis(bipyridine)ruthium(II) chloride hydrate, [(bpy)₂Ru(5-phenNH₂)]Cl₂·H₂O, are shown to oxidize hydrazine with excellent sensitivity. The presence of an amine group on the ruthenium complex facilitates electropolymerization onto the electrode surface. Using cyclic voltammetry, a large catalytic current is observed upon oxidation of hydrazine in phosphate buffer (pH 5.0), compared to the current obtained from the ruthenium-modified electrode with no hydrazine present. The sensitivity of cyclic voltammetry is sufficient for obtaining a linear calibration curve for hydrazine over the range of 10⁻⁵ to 10⁻² M. Hydrodynamic amperometry was used to determine the working potential for flow injection analysis. The limit of detection for hydrazine was determined to be 8.5 μM using FIA. The thickness of these films was shown to increase linearly with the number of electropolymerization cycles, in the range of 1000-2500 nm for 5-20 cycles, respectively, using Rutherford backscattering spectrometry (RBS). RBS analysis also suggests that the film is multilayered with the outermost layers containing a high ruthenium concentration, followed by layers where the concentration of ruthenium decreases linearly and approaches zero at the electrode surface.     

A perylenedicarboxamide linker for DNA hairpins

The synthesis and properties of a perylenediamide diol linker and several DNA hairpins possessing this linker are described. The diol linker absorbs and fluoresces strongly in the visible. Hairpins having poly(dA)-poly(dT) stems have fluorescence quantum yields and decay times similar to those of the linker, indicating that hole injection does not occur from the singlet excited linker into the base pair domain. Fluorescence quenching by dG or dZ bases is observed when these bases are located near the linker. The strong distance dependence of fluorescence quenching is consistent with a superexchange mechanism for electron transfer. Failure to observe formation of the linker anion radical by means of femtosecond time resolved absorption spectroscopy is attributed to fast charge recombination. The properties and behavior of the perylene linker and its hairpins are compared to those of other arenedicarboxamide linkers.     

反应注射成型聚氨酯互穿聚合物网络研究——刚性网络对于体系形态及性能的影响

用微型反应注射成型机制备了以聚氨酯(PU)为弹性相的两类同步互穿聚合物网络(SIN),其刚性相分别采用保留仲羟基的乙烯基酯树脂(VERH)以及封闭仲羟基的乙烯基酯树脂(VERA)。用傅里叶变换红外光谱在线跟踪了这类互穿网络的生成过程,发现刚性网络抑制了PU网络中硬段有序结构的形成,两个网络间有一定程度的互穿,而两个网络间的化学键作用进一步削弱氢键强度。自旋—自旋弛豫时间的测定进一步表明网络间存在一定的互穿以及刚性相对于PU硬段结晶的抑制作用。材料的力学性能与其SIN的形态有关。VERA网络对PU表现出明显的增强作用,而由VERH网络形成的SIN则由于体系相分离进程受到严重阻碍而使材料性能恶化。     

工业废水中微量铜（Ⅱ）和氰化物的流动注射光度分析

采用ＦＩＡ技术，以光度比色法为基础，建立了工业废水中微量Ｃｕ＾２＋和ＣＮ＾－的顺序自动分析方法和装置。其对二种离子的测定频率为６０样／ｈ，相对标准偏差＜１．０％，工作曲线的ｒ值≥０．９９９，各项分析技术指标均优于手工法操作。     

Determination of total phosphorus and nitrogen in turbid waters by oxidation with alkaline potassium peroxodisulfate and low pressure microwave digestion, autoclave heating or the use of closed vessels in a hot water bath: comparison with Kjeldahl digestion

The evaluation of the use of alkaline peroxodisulfate digestion with low pressure microwave, autoclave or hot water bath heating for the determination of total phosphorus and nitrogen in turbid lake and river waters is described. The efficiency of these digestion procedures were compared to a Kjeldahl digestion procedure with sulphuric acid-potassium sulfate and copper sulfate. The final solution before digestion was 0.045 M in potassium peroxodisulfate and 0.04 M in sodium hydroxide. Procedures were evaluated by the analysis of suspensions of two reference materials, National Institute of Environmental Science, Japan, no. 3 Chlorella and no. 2 pond sediment and natural turbid waters. Best recoveries of phosphorus and nitrogen by microwave heating were obtained when solutions were digested at 95 °C for 40 min. Quantitative recoveries of phosphorus from Chlorella suspensions up to 1000 mg/l were obtained by all three heating procedures, but incomplete recoveries of nitrogen occurred above 20 mg N/l in the digested sample. Good recoveries of phosphorus and nitrogen from suspended sediment suspensions were obtained only from solutions containing <150 mg/l of suspended sediments. Recoveries of phosphorus from phosphorus compounds containing COP and CP bonds added to distilled water were quantitative (94-113%) except for polyphosphates (microwave, 34±8; autoclave, 114±6; water bath, 96±4) and aluminium phosphate (8-23%). Recoveries of nitrogen compounds containing CN bonds added to distilled water were quantitative (94-96%). The analysis of a range of natural turbid water samples by alkaline peroxodisulfate and microwave, autoclave and water bath heating gave similar total phosphorus and nitrogen results. All procedures using alkaline peroxodisulfate underestimate phosphorus concentrations at high suspended sediment concentrations (>150 mg/l) and are only suitable for the analysis of very turbid samples when the turbidity is due to organic matter (algal cells, plant detritus). Underestimation of nitrogen occurs when samples contain more than 20 mg N/l.     

Solventless injecction for packed column supercritical fluid chromatography

The adverse effects of injection solvent strength on microbore packed column SFC band broadening are demonstrated and a solventless injection system that eliminates these effects is introduced. The injection system removes solvent in a GC-like manner using a retention gap and an on-column capillary GC syringe. The analyte is delivered to the analytical column in a solvent-free plug of supercritical fluid mobile phase.     

Flow injection-spectrophotometric determination of cresol compounds in water by reaction withp-aminophenol

A spectrophotometric method has been developed for the simultaneous determination ofo-cresol andm-cresol in water by reaction withp-aminophenol (PAP). Three different methodologies have been assayed; (i) batch analysis, after reaction in an alkaline medium in the presence of dissolved molecular oxygen as oxidizing agent, (ii) a stopped-flow procedure, carried out in the presence of KIO₄ and (iii) a flow injection method based on the same approach. The batch procedure requires 22 min for the full development of colour witho-cresol and 12 min form-cresol. In the stopped-flow mode, using KIO₄ and a reaction time of 12 min, better sensitivity can be obtained for both compounds and limits of detection of 10 g 1^–1 foro-cresol and 30 g 1^–1 form-cresol were found. The flow injection method has a lower sensitivity but permits more than 80 injections per hour. Based on the different maximum absorbance wavelengths obtained for the reaction products of PAP witho-cresol (614 nm) andm-cresol (632 nm), both compounds can be simultaneously determined in water samples and recoveries of 90 to 115% were found in spiked water samples of different types.     

Flow injection system for hydrolysable tannin determination

A flow injection system was proposed to evaluate the transient product of a colorimetric reaction between hydrolysable tannin and potassium iodate (KIO₃) solution. The system optimization was accomplished by using statistical methods based on experimental design. Flow rate of KIO₃ solution, sample volume, carrier flow rate, and reaction coil were the selected factors for evaluation. On screening step, complete factorial 2⁴ was used and two levels for each selected factor were studied. For the optimization phase, a centered face composite design 2² + star was employed to evaluate sample volume and flow rate of KIO₃ solution, which were the factors identified in the screening phase as having more influence on the absorbance signal. After optimization, the proposed system was compared with batch determination. Some characteristics, such as analytical frequency, reagent consumption and chemical residues generation presented better results by the use of the proposed system if compared with batch method. The system presented good repeatability with standard deviation lower than 3%, for n = 10, linearity (R² = 0.9974) for tannic acid standard, analytical frequency of 15 injections h^− 1 and limit of quantification of 24 mg L^− 1 of tannic acid. Good results were obtained when the proposed system was applied to hydrolysable tannin determination in Stryphnodendron barbatimão, Eucalyptus citriodora and Phyllanthus niruri, samples of plants commonly used in popular medicine.