Methyl concentration time-histories during iso-octane and n-heptane oxidation and pyrolysis

Methyl radical concentration time-histories were measured during the oxidation and pyrolysis of iso-octane and n-heptane behind reflected shock waves. Initial reflected shock conditions covered temperatures of 1100-1560 K, pressures of 1.6-2.0 atm and initial fuel concentrations of 100-500 ppm. Methyl radicals were detected using cw UV laser absorption near 216 nm; three wavelengths were used to compensate for time- and wavelength-dependent interference absorption. Methyl time-histories were compared to the predictions of several current oxidation models. While some agreement was found between modeling and measurement in the early rise, peak and plateau values of methyl, and in the ignition time, none of the current mechanisms accurately recover all of these features. Sensitivity analysis of the ignition times for both iso-octane and n-heptane showed a strong dependence on the reaction C₃H₅ + H = C₃H₄ + H₂, and a recommended rate was found for this reaction. Sensitivity analysis of the initial rate of CH₃ production during pyrolysis indicated that for both iso-octane and n-heptane, reaction rates for the initial decomposition channels are well isolated, and overall values for these rates were obtained. The present concentration time-history data provide strong constraints on the reaction mechanisms of both iso-octane and n-heptane oxidation, and in conjunction with OH concentration time-histories and ignition delay times, recently measured in our laboratory, should provide a self-consistent set of kinetic targets for the validation and refinement of iso-octane and n-heptane reaction mechanisms.     

JP-10点火延时的激波管研究

在预加热激波管上测定了JP-10的点火延时时间．采用高精度真空仪直接测定注入激波管中JP-10蒸气压力，获得了JP-10气相浓度，解决了高碳数碳氢燃料点火延时激波管实验时管壁吸附影响燃料气相浓度确定的困难．采用压力传感器、单色仪和光电倍增管记录得到了完整的点火过程引起的压力变化和OH或CH自由基发射强度变化．自由基发射信号作为诊断点火发生的手段．当实验压力为151?556 kPa，温度为1000?2120 K，JP-10摩尔百分比为0.1%?0.55%，化学当量比为0.25、0.5、1.0、2.0时，获得了点火延时时间与实验温度、JP-10浓度、O2浓度的依赖关系，结果还表明，高温区和低温区呈现出不同的依赖关系．     

基于菲佐干涉仪与多通道光电倍增管阵列的多普勒频移检测技术

提出了基于菲佐干涉仪和多通道光电倍增管(PMT)阵列探测器组合的多普勒频移检测的方案,适用于风速测量的直接探测多普勒激光雷达。首先介绍了工作原理,再根据菲佐干涉仪光谱特征对频移检测用干涉仪进行了优化设计,优化设计的菲佐干涉仪腔长150mm、平板反射率0．755。对提出的菲佐干涉仪和多通道光电倍增管阵列探测器组合的方案进行了数值模拟,以分子散射作为背景噪声,计算了该方法的风速测量误差。模拟结果表明,设计的基于菲佐干涉仪的直接探测多普勒测风激光雷达,在30 s的积分时间内、探测高度5 km以下,风速测量误差可以达到0．56 m/s。     

汽化滞后的毛细管内流动模型与计算

基于均相流模型,建立了制冷剂在毛细管内绝热流动的数学模型,同时考虑了管内流动过程中实际存在的汽化滞后问题。针对工质为R22的制冷系统,开发了程序进行流动模拟计算,该程序对于制冷系统毛细管的匹配具有实用价值。     

Linear theory of an electron cyclotron maser operating at the fundamental

The linear theory of an electron cyclotron maser (ECM) operating at the fundamental is developed. A set of analytic expressions, valid for all TE cavity modes, is derived for the starting current and frequency detuning using the Vlasov-Maxwell equations in the weakly relativistic limit. These results are applicable for an arbitrary electron velocity distribution as well as any longitudinal distribution of the RF field. It is shown that the starting current can be expressed in a simple form which contains the Fourier trans-form of the longitudinal field distribution. Analytic results are presented for specific longitudinal field variations, including uniform, sinusoidal, and Gaussian. It is found that the starting characteristics of an ECM are strongly influenced by the axial dependence of the RF field, but weakly affected by the velocity spread of the electron beam. The problem of multimode oscillation is treated in the linear theory by using a Slater expansion of the cavity field. The complete formulation for mode competition based on this expansion is presented and preliminary results are derived. This comprehensive analysis of ECM linear theory should be useful as a diagnostic of ECM performance and should facilitate comparison between theory and experiment.Work supported by U.S.D.O.E. Contract DE-AC-02-80ER52059Supported by U.S. Department of EnergySupported by National Science Foundation     

Laryngeal and pharyngeal behavior in countertenor and baritone singing—A videofiberscopic study

Changes in vocal tract configuration during singing were studied in four semiprofessional countertenors and one professional bass-baritone, by means of fiberoptic laryngoscopy. All of the countertenors showed a marked narrowing of the lower pharynx with increasing pitch when they used their countertenor voice (CT voice) but only a slight narrowing when using their baritone voice (B voice). The bass-baritone's pharynx remained unchanged with increasing pitch. Increasing loudness gave a widening of the pharynx in three of the four countertenors' CT voices, whereas no change was observed for the countertenors' B voices or for the bass-baritone voice. Vocal fold length seemed to decrease in one countertenor's B voice and in the bass-baritone with increasing loudness. Thus, the countertenors in this study exhibit several characteristic patterns of vocal tract gestures in countertenor voice that differ from both their own baritone voices and from the bass-baritone.     

曲折圆形槽波导慢波系统的高频特性

 对曲折圆形槽波导新型慢波系统的高频特性进行了研究，通过理论分析和数值计算，得到了它的色散曲线和耦合阻抗表达式，并分析了结构参数变化对色散特性和耦合阻抗的影响。研究表明：当周期变小时色散减弱，耦合阻抗增加；而增大直波导长度时色散变弱，但同时耦合阻抗也会下降。因此较小的周期有利于改善曲折圆形槽波导慢波电路的高频特性。鉴于这种电路的耦合阻抗较低，可以适当地减小直波导长度来提高耦合阻抗。曲折槽波导结合了曲折波导散热能力强、色散特性好、容易加工和槽波导单模工作、低损耗、大尺寸等优点，在毫米波及亚毫米波段的行波管中具有较好的发展前景。     

预应力钢管混凝土组合构件的稳定性研究

给出了预应力筋初始张拉力和有效张拉力的计算方法．根据弹性力学理论和能量法原理,建立了组合构件挠曲微分方程,推导了各种边界条件的预应力钢管混凝土组合构件的压屈载荷计算公式,并由强度条件确定了界限长细比．算例分析表明,对超过界限长细比的钢管混凝土组合构件,施加预应力可以有效地提高其稳定承载力．     

圆管及内充压力介质管道撞击损伤与破坏的研究进展

综述了国内外关于内空圆管及充有压力介质的管道经受局部撞击作用时的大变形与破坏的研究现状,从圆管的侧向撞击凹陷及其对管柱承载能力的影响、管壁的撞击穿透、圆管的斜冲击、内充介质及压力对冲击穿透的影响、分析模型等6个方面介绍了一些重要实验结果和处理该类问题的分析方法与力学模型,讨论并提供了一些在工程应用中有重要指导意义的研究结果.由于内充压力介质管道的冲击穿透破坏涉及内充压力介质与管壁在撞击过程中的相互耦合作用,其变形及破坏机理十分复杂,影响因素除了圆管的几何尺寸、支承形式、材料力学特性、弹体形状及冲击速度等,还包括内充介质密度及内充压力大小等诸多方面.本文对这一问题作了详细评述及讨论,指出了目前的研究结果中的不同结论,同时给出了内充压力介质对临界冲击穿透能量的影响趋势的最新研究结果,最后提出了进一步的研究方向以及采用的相应对策.图2参64     

Data reduction for air-side performance of fin-and-tube heat exchangers

The present study focuses on the data reduction method to obtain the air-side performance of fin-and-tube heat exchangers. The data reduction methodology for air-side heat transfer coefficients in the literature is not based on a consistent approach. This paper recommends standard procedures for dry surface heat transfer in finned-tube heat exchangers having water on the tube-side. Inconsistencies addressed include the -NTU relationships, calculation of the tube-side heat transfer coefficient, calculation of fin efficiency, and whether entrance and exit loss should be included in the reduction of friction factors. Use of the recommended standardized methodology will provide more meaningful data for use in the development of correlations, or for performance comparison purposes.