Universal arcs in local tournaments

An arc $uv$ of a digraph $D$ is called universal if $uv$ and $w$ are in a common cycle for any vertex $w$ of $D$. In this paper we characterize local tournaments whose every arc is universal.     

金属蒸气真空弧离子源CO离子注入对不锈钢摩擦磨损性能的影响

采用金属蒸气真空弧离子源对1Cr18Ni9Ti不锈钢进行Co离子注入,考察了注入处理试样的摩擦磨损性能.结果表明:Co注入处理样品的表面硬度比未注入样品的高1.0～1.5倍,且硬度随离子束流密度的增大而增大;Co注入处理试样的摩擦系数显著降低至约0.20,磨损体积损失降低25%～45%;当束流密度为22μA/cm2、注入剂量为5×1017/cm2时,注入处理样品的摩擦系数为0.19,耐磨寿命最长;在所选定的试验参数范围以内,当临界束流密度处于22μA/cm2时,保留剂量最大,改性表面硬度最高,耐磨性能最佳.     

NUMERICAL ANALYSIS OF ARC MOTION IN RAILGUN MUZZLE UNDER THE EFFECT OF BACKFLOW

在电磁轨道炮发射过程中,膛口外的高温气团以远高于声速的运动速度向内膛运动,这会使得膛口的电弧形态发生改变以及电弧位移。为了实现膛口电弧运动过程的数值计算,本文基于磁流体理论,引入了一种和电弧等离子体自身电导率密切相关的电位边界条件处理方法,建立了膛口位置电弧仿真模型。对回流效应下的电弧运动规律进行了分析,并且研究了运动过程中电弧对内膛流场的温度分布产生的影响。结果表明电弧的运动加剧了膛内温升。     

冲击速度和磨粒粒度对FeCrAl/WC复合涂层冲蚀性能的影响

采用粉芯丝材作为原料,利用高速电弧喷涂技术制备了具有良好抗高温冲蚀磨损性能的FeCrAl/WC复合涂层;考察了650℃下冲击速度和磨粒粒度对复合涂层高温冲蚀磨损性能的影响.结果表明,复合涂层和20G锅炉钢的耐高温冲蚀磨损能力随着磨粒粒度的增加而有所提高;30°攻角下冲蚀率随磨粒粒度的变化速率比90°攻角下的小;同20G锅炉钢相比,复合涂层对速更加敏感,速度越低,FeCrAl/WC复合涂层的抗冲蚀磨损性能越好.     

Interfacial Studies for improving the adhesion of Cr/Al films on composites

The composites, such as CFRP and GFRP, have been widely applied in spaceflight, for their low specific gravity, low cost, and additional structural stability. However, the high resistivity of the composites severely inhibits their further applications. Therefore, Cr/Al films with low resistivity and high adhesion were deposited on composites by cathodic arc technique. The films were characterized by pull test, Dektak 8 Stylus Profilometer, SEM, XPS, XRD and Z‐82 standard four probes. Results show that the aluminum film of fcc structure is compact and uniform, with resistivity as low as bulk Al. The adhesion between Cr buffer layer and composite substrate was greatly enhanced because of the formation of the chemical bonds, such as Cr? C, Cr? O and Cr? N, at the Cr/composite interface. Copyright © 2011 John Wiley & Sons, Ltd.     

Routing problems: A bibliography

This bibliography contains 500 references on four classical routing problems: the Traveling Salesman Problem, the Vehicle Routing Problem, the Chinese Postman Problem, and the Rural Postman Problem. References are presented alphabetically under a number of subheadings.     

用正交光路全息干涉CT技术重建电弧等离子体三维温度场

本文利用正交光路全息干涉技术和计算机有限角层析算法,借助电弧等离子体物理方程,对非对称电弧等离子体三维温度场的诊断进行了研究.     

Multiwalled carbon nanotubes mass-produced by dc arc discharge in He–H2 gas mixture

Uniform cathode deposits (longer than 15 mm), containing multiwalled carbon nanotubes (MWNTs) inside, were produced by dc arc discharge evaporation with a computer-controlled feeder of a pure-carbon electrode without a metal catalyst in a He–H₂ gas mixture. The purification of MWNTs was carried out to remove amorphous carbon and carbon nanoparticles. High-resolution transmission electron microscopy observations and Raman scattering studies show that the MWNTs possess a high crystallinity and a mean outermost diameter of ∼ ∼10 nm. It has been confirmed that the current density in the electron field emission from a purified MWNT mat can reach 77.92 mA/cm², indicating that the purified MWNTs are a promising candidate electron source in a super high-luminance light-source tube or a miniature X-ray source.     

测试屏幕上B、C两点所对应的聚焦现象及其亮度比初步分析

根据相对聚焦强度公式,分析了灯丝上发出的光线在通过旋转抛物面反射到测试屏幕上的B,C两点时所具有的完全聚焦现象,并说明了这种聚焦的现象是一阶的.进一步,我们还给出了相对聚光强度的各种比值,并据此给出了在满足B点亮度不小于C点亮度的两倍的条件下,灯丝的最短长度为3.122mm.