塞曼石墨炉原子吸收光谱法测定粉尘降尘中痕量锡

以KOH熔样,又以KOH作基体改进剂,研究了测定锡的灰化温度、原子化行为和消除干扰及试样前处理的方法,以KOH熔解的粉尘及降尘样液,特别适用于塞曼石墨炉的测定,背景可完全扣除。方法简便、快速、准确,灵敏度和精度高。相对标准偏差为4.0%,回收牢在96.4～110%范围内。     

Preparation and microwave absorption properties of electroless Co-Ni-P coated strontium ferrite powder

A new type of Co-Ni-P coated strontium ferrite nanocomposite was prepared with electroless plating enhanced by ultrasonic wave at room temperature. The plating process was studied carefully. The morphology, crystal structure and microwave absorption properties of the Co-Ni-P coated powder were studied with field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), energy dispersive analysis of X-rays (EDX) and vector network analyzer. The results show that the strontium ferrite powder was successfully coated with Co-Ni-P alloy and possesses excellent microwave absorption properties. The maximum microwave loss of the composite powder reaches −44.12 dB. The bandwidth with the loss above −10 dB exceeds 13.8 GHz.     

Low sintering temperature MnZn-ferrites for power applications in the frequency region of 400 kHz

In this paper, the effect of cubic zinc metaborate Zn₄O(BO₂)₆ on the sintering of MnZn-ferrites for medium frequency power applications is investigated. Zinc metaborate is synthesized in the laboratory using zinc oxide and boric acid as metal precursors. As observed, when zinc metaborate is added to the MnZn-ferrites at an optimum amount of 0.02 wt%, it significantly enhances densification and therefore allows, for a given density, reduction of the firing temperature by almost 200 °C. MnZn-ferrites exhibiting power losses of 70 mW/cm³ (measured at a frequency of 400 kHz, magnetic field 50 mT and temperature of 90 °C) are synthesized from conventionally milled powders with average particle diameter 0.6 μm, compacted and fired at 1100 °C. Identical experiments conducted under the same conditions on specimens without zinc metaborate additions revealed power losses greater than 300 mW/cm³, because of insufficient densification.     

火焰原子吸收光谱法测定巨大口蘑子实体中的铁、锌和锰

采用火焰原子吸收光谱法测定了巨大口蘑子实体中的微量元素铁、锌和锰的含量,方法简单,精密度和灵敏度高,相对标准偏差为0.378%-0.842%,回收率95.83%-99.45%.     

Electrical conductivity of chromate conversion coating on electrodeposited zinc

For certain applications of galvanized steel protected with conversion coatings it is important that the surface is electrically conductive. This is especially important with mating surfaces for electromagnetic compatibility. This paper addresses electrical conductivity of chromate conversion coatings. A cross-matrix study using different zinc plating techniques by different labs showed that the main deciding factor is the type of zinc-plating bath used rather than the subsequent chromating process. Thus, chromated zinc plate electrodeposited from cyanide baths is non-conductive while that from alkaline (non-cyanide) and acid baths is conductive, even though the plate from all the bath types is conductive before conversion coating. The results correlate well with the microscopic structure of the surfaces as observed with scanning electron microscopy (SEM) and could be further corroborated and rationalized using EDX and Auger spectroscopies.     

Influence of buffer layer thickness on the structure and optical properties of ZnO thin films

A series of ZnO thin films were deposited on ZnO buffer layers by DC reactive magnetron sputtering. The buffer layer thickness determination of microstructure and optical properties of ZnO films was investigated by X-ray diffraction (XRD), photoluminescence (PL), optical transmittance and absorption measurements. XRD results revealed that the stress of ZnO thin films varied with the buffer layer thickness. With the increase of buffer layer thickness, the band gap edge shifted toward longer wavelength. The near-band-edge (NBE) emission intensity of ZnO films deposited on ZnO buffer layer also varied with the increase of thickness due to the spatial confinement increasing the Coulomb interaction between electrons and holes. The PL measurement showed that the optimum thickness of the ZnO buffer layer was around 12 nm.     

Self-organized ZnAl2O4 nanostructures grown on -sapphire

Self-organized ZnAl₂O₄ nanostructures with the appearance (in SEM) of high aspect ratio horizontal nanowires are grown on uncatalysed c-sapphire by vapour phase transport. The nanostructures grow as three equivalent crystallographic variants on c-sapphire. Raman and cathodoluminescence spectroscopy confirm that the nanostructures are not ZnO and TEM shows that they are the cubic spinel, zinc aluminate, ZnAl₂O₄, formed by the reaction of Zn and O with the sapphire substrate.     

Azine bridged silver coordination polymers: Powder X-ray diffraction route to crystal structure determination of silver benzotriazole

In continuation of our interest in solid-state structures of silver complexes of photographic importance, the structure for silver benzotriazole (AgBZT), has now been obtained. The preferred method for solving crystal structures is via single-crystal X-ray diffraction (XRD). However, for some materials, growing single crystals of appropriate size and quality is often difficult or even impossible. AgBZT is an example of such a silver complex with poor solubility. The usual routes to preparing single crystals using recrystallization from a cooperating solvent resulted in polycrystalline powder samples. We propose a crystal structure for AgBZT, solved from synchrotron X-ray powder diffraction data, using a direct-space Monte Carlo simulated annealing approach. AgBZT crystals are monoclinic, (P2₁/c), with unit cell dimensions, a=14.8052(3) Å, b=3.7498(4) Å, c=12.3495(12) Å, and β=114.200(6)°. The AgBZT complex is constructed from all three of the Benzotriazole (BZT) nitrogens bonding to a separate silver atom. As a consequence of this bonding mode, the structure is a highly cross-linked, coordination polymer.     

Synthesis, morphology and random laser action of ZnO nanostructures

Three-dimensional (3-D) ZnO random-wall nanostructures and one-dimensional (1-D) ZnO nanorods were prepared on silicon substrates by a simple solid-vapour phase thermal sublimation technique. Optical pumped random lasing has been observed in the ZnO random-wall arrays with a threshold intensity of 0.38 MW/cm² in the emission wavelength from 380 to 395 nm. The optical gain was attributed to the closed-loop scattering and light amplification of the ZnO random-wall. The experimental result suggests that the morphology of nanostructure is the key factor to effect random lasing.