Shape effect of elongated grains on ultrasonic attenuation in polycrystalline materials

Longitudinal and transverse wave attenuation coefficients are obtained in a simple integral form for ultrasonic waves in cubic polycrystalline materials with elongated grains. Dependences of attenuation on frequency and grain shape are described in detail. The explicit analytical solutions for ellipsoidal grains in the Rayleigh and stochastic frequency limits are given for a wave propagating in an arbitrary direction relative to ellipsoid axes. The attenuation exhibits classic frequency dependence in those frequency limits. However, the dependence on the grain shape in the stochastic limits is unexpected: it is independent of the cross-section of the ellipsoidal grains and depends only on the grain dimension in the propagation direction. In the Rayleigh region attenuation is proportional to effective volume of the ellipsoidal grain and is independent of its shape. A complex behavior of attenuation on the grain shape/size and frequency is exhibited in the transition region. The results obtained reduce to the classic dependences of attenuation on parameters for polycrystals with equiaxed grains.     

A new standing-wave-type linear ultrasonic motor based on in-plane modes

This paper presents a new standing-wave-type linear ultrasonic motor using combination of the first longitudinal and the second bending modes. Two piezoelectric plates in combination with a metal thin plate are used to construct the stator. The superior point of the stator is its isosceles triangular structure part of the stator, which can amplify the displacement in horizontal direction of the stator in perpendicular direction when the stator is operated in the first longitudinal mode. The influence of the base angle θ of the triangular structure part on the amplitude of the driving foot has been analyzed by numerical analysis. Four prototype stators with different angles θ have been fabricated and the experimental investigation of these stators has validated the numerical simulation. The overall dimensions of the prototype stators are no more than 40 mm (length) × 20 mm (width) × 5 mm (thickness). Driven by an AC signal with the driving frequency of 53.3 kHz, the no-load speed and the maximal thrust of the prototype motor using the stator with base angle 20° were 98 mm/s and 3.2 N, respectively. The effective elliptical motion trajectory of the contact point of the stator can be achieved by the isosceles triangular structure part using only two PZTs, and thus it makes the motor low cost in fabrication, simple in structure and easy to realize miniaturization.     

Synthesis of low-melting-point metallic nanoparticles with an ultrasonic nanoemulsion method

A one-step, economical nanoemulsion method has been introduced to synthesize low-melting-point metallic nanoparticles. This nanoemulsion technique exploits the extremely high shear rates generated by the ultrasonic agitation and the relatively large viscosity of the continuous phase - polyalphaolefin (PAO), to rupture the molten metal down to diameter below 100 nm. Field’s metal nanoparticles and Indium nanoparticles of respective average diameters of 15 nm and 30 nm have been obtained. The nanoparticles size and shape are determined by transmission electron microscopy (TEM). Their phase transition behavior is examined using a differential scanning calorimeter (DSC). It is found that these nanoparticles dispersed in PAO can undergo reversible, melting-freezing phase transition, and exhibit a relatively large hysteresis. The experimental results suggest that the nanoemulsion method is a viable route for mass production of low-melting nanoparticles.     

Effect of ultrasonic irradiation on structure and electrochemical properties of LiMn2O4 thin films cathode material for Li-ion micro-batteries

Two kinds of spinel LiMn₂O₄ thin film for lithium ion micro-batteries were successfully prepared on polycrystal Pt substrates by spin coating methods, which were carried out under ultrasonic irradiation (USG) and magnetic stirring (MSG), respectively. The microstructures and electrochemical performance of LiMn₂O₄ thin films were characterized by thermogravimetry analysis (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM), and galvanostatic charge-discharge measurements. It was found that the crystalline structure of USG samples grew better than that of the MSG samples. At the same time, higher discharge capacity and better cycle stability were obtained for the LiMn₂O₄ thin films of USG at the current density of 50 μAh/cm² between 3.0 and 4.3 V. The 1st discharge capacity was 57.8 μAh/cm²-μm for USG thin films and 51.7 μAh/cm²-μm for MSG thin films. After 50 cycles, 91.4% and 69% of discharge capacity could be retained respectively, indicating that ultrasonic irradiation condition during spin coating was more suitable for preparing spinel LiMn₂O₄ thin films with better electrode performance for lithium ion micro-batteries.     

Studies on nano suspensions of silver sol and redispersed nanocrystallite silver in aqueous and alcoholic media

Nanocrystallite silver and silver sol were prepared and characterized by UV-visible spectra, XRD, TEM and HRTEM. The crystallite silver is re-dispersed in two different media, namely, water and alcohol and sonicated before ultrasonic investigation. The silver sol was used as such. Three different models for the propagation of ultrasound through two phase media are compared in these three different types of nano suspensions. Effect of particle size and medium on ultrasonic velocity (U), compressibility (κ) impedance (Z) and viscous relaxation time (τ) is studied. The particle concentration range was 0.2-1 v/v. Density and viscosity of the dispersion and sol are measured at different particle volume fractions. Effective density and ultrasonic velocity are computed by Urick, Kuster and Toksöz and Urick and Ament models and compared with experimental velocities. Values of effective density obtained by using Urick and Urick and Ament equations closely agree with experimental results of density while Urick's equation prediction of velocity is in close agreement with the experimental velocities. This comes as a surprise in view of the large density difference between the medium and suspended particle and suggests the possibility of the balancing effect of the inertial and viscous forces operating in the suspension.     

超声喷雾热解法制备SnS薄膜的物性研究

用超声喷雾热解法制备SnS多晶薄膜,对比了三种不同前驱液配比浓度对SnS薄膜性能的影响。XRD测试表明,当前驱液为硫脲(0.5 mol·L-1)+四氯化锡(0.5 mol·L-1)+去离子水时,SnO2的衍射峰强度比较大;当前驱液为硫脲(0.6 mol·L-1)+四氯化锡(0.5 mol·L-1)+去离子水时,SnS的衍射峰占主要地位,其中也含有一定量的SnO2;当前驱液为硫脲(0.7 mol·L-1)+四氯化锡(0.5 mol·L-1)+去离子水时,退火后的薄膜为单一的SnS薄膜,具有斜方晶系结构。SEM观测发现,薄膜均匀、致密,前驱液中硫脲浓度较大时,颗粒也较大。透过谱测试表明,浓度对薄膜透过率影响较小。结合器件的暗I-V和C-V测试,用三种前驱液配比浓度所制备的器件的结特性差异不大;当前驱液中硫脲浓度较大时,载流子浓度相对较大。     

The effect of solute on ultrasonic grain refinement of magnesium alloys

An experimental study has been conducted to assess the structural refinement of magnesium and its alloys by ultrasonic irradiation during solidification. It is shown that (i) ultrasonic irradiation leads to significant refinement only in the presence of adequate solute, which is alloy dependent; (ii) the attendant grain density increases linearly with increase in solute content at a given irradiation level; (iii) increasing the solute content at a low irradiation level above the cavitation threshold is more effective than substantially increasing the irradiation intensity; and (iv) the difference in the grain size between two ultrasonicated magnesium alloys is mainly determined by the solute content rather than the irradiation intensity. In view of these, the effect of ultrasonic irradiation on solute redistribution in a solidifying magnesium alloy seems rather limited even at a substantial intensity level such as 1700 W cm⁻². The implications of these findings are discussed and a mechanism is proposed to account for the experimental observations.     

Determination of three-dimensional solubility parameters of chlorinated polypropylene by ultrasonic degradation

The degradation reactions of chlorinated polypropylene (CPP) in toluene under ultrasonic irradiation were studied. The Mark–Houwink equation acquired from fractional precipitations was also suitable for estimating the molecular weight of degraded CPP. An objective standard was proposed for judging the solution behaviour of CPP in solvents by the study on the relative solubility of CPP before and after degradation. Then Hansen three-dimensional solubility parameters and the total parameter of CPP were obtained by optimization calculation in terms of the criterion proposed here. It was proved that the total parameter of CPP is creditable by the turbidity method. Compared to other standards, the result obtained from the proposed standard accorded well with the standard of complete miscibility suggested by Flory–Huggins for polymers and solvents as well as the objective reality. This standard may provide a reference for other polymers.     

Analysis of benzophenone and 4-methylbenzophenone in breakfast cereals using ultrasonic extraction in combination with gas chromatography-tandem mass spectrometry (GC-MS)

Benzophenone (BP) and 4-methylbenzophenone (4MBP) are photo-initiators that are generally used to cure ink on carton boards.In this contribution, a fast and reliable method for the determination of BP and 4MBP in breakfast cereals is described. The sample was extracted ultrasonically using a mixture of dichloromethane and acetonitrile (1:1), followed by a clean-up of the extract using solid phase extraction with a silica cartridge. Finally, the extract was analysed by GC-MSⁿ. Benzophenone-d₁₀ was used as internal standard. The presented method is validated in terms of linearity, recovery, repeatability and intra-laboratory reproducibility, specificity, limit of detection and limit of quantification. In conclusion, this method is able to detect both BP and 4MBP at very low concentrations (LOD = 2 μg kg⁻¹) in breakfast cereals.     

Scattering of plane acoustic waves by a transversely isotropic cylindrical shell—application to material characterization

Scattering of obliquely incident plane acoustic wave by an air-filled, transversely isotropic cylindrical shell immersed in water is investigated theoretically and experimentally. The normal mode expansion technique is employed for analyzing the scattering field, and then resonance modes of the shell appearing in modal scattering form functions are identified performing the resonance scattering analysis. Dispersion curves for Sholte-Stoneley, SH and Lamb waves are obtained and their characteristics are interpreted. Calculated backscattering and resonance spectra as well as dispersion curves are compared with those from ultrasonic experiments for two composite samples having the same nominal composition but fabricated under different conditions. Sensitive change of the dispersion curves is observed for both normal and oblique incidences, which demonstrates the feasibility of systematic inverse evaluation of damage or elastic constants of the composite shell using data from the acoustic scattering measurements.