LOCAL BENDING OF THIN FILM ON VISCOUS LAYER

Effects of deposition layer position film are systematically investigated. Because the and number/density on local bending of a thin deposition layer interacts with the thin film at the interface and there is an offset between the thin film neutral surface and the interface, the deposition layer generates not only axial stress but also bending moment. The bending moment induces an instant out-of-plane deflection of the thin film, which may or may not cause the socalled local bending. The deposition layer is modeled as a local stressor, whose location and density are demonstrated to be vital to the occurrence of local bending. The thin film rests on a viscous layer, which is governed by the Navier-Stokes equation and behaves like an elastic foundation to exert transverse forces on the thin film. The unknown feature of the axial constraint force makes the governing equation highly nonlinear even for the small deflection chse. The constraint force and film transverse deflection are solved iteratively through the governing equation and the displacement constraint equation of immovable edges. This research shows that in some special cases, the deposition density increase does not necessarily reduce the local bending. By comparing the thin film deflections of different deposition numbers and positions, we also present the guideline of strengthening or suppressing the local bending.     

光纤弯曲损耗特性的理论与实验研究

为了减小在长距离光纤通信中存在的弯曲损耗和利用光纤激光器中的弯曲损耗获得单模输出，利用速度法解释了光纤弯曲损耗机制，采用Marcuse理论研究了弯曲损耗随弯曲半径、波长和纤芯半径变化的关系。通过计算机仿真和实验得出弯曲损耗随弯曲半径的减小而增大，随波长的增大而增大，随纤芯半径的增大而增大，高阶模式的损耗大于低阶模式。利用这一结论就可以通过控制弯曲半径在临界半径以内来减小通信中的弯曲损耗，通过增大模场半径来实现光纤激光器中的单模输出。     

用动力学法测杨氏模量实验及其实验装置的研制

介绍了新研制的用动力学法杨氏模量的实验装置,它具有功耗低,灵敏度高的特点;教学中测量悬线不同位置时的共振频率,用作图法拟合出其精确值,以减少由于悬线不在节点引起的系统性误差,测量精密度比传统的静态拉伸法高一个量级以上。     

Dynamic Behavior of Rigid–Plastic Sector Plates

The paper studies the dynamic behavior of perfect rigid-plastic plates in the form of a sector with hinged or clamped sides under short-term intensive loads. Two dynamic deformation mechanisms are demonstrated. The dynamic equation is derived for each of the mechanisms. The realization conditions for the mechanisms are analyzed. Analytical expressions are derived for the ultimate (high) loads and the maximum residual deflection. Numerical examples are given     

Positive solutions for three-point boundary value problems with dependence on the first order derivative

A new fixed point theorem in a cone is applied to obtain the existence of at least one positive solution for the second order three-point boundary value problem

     

Valence band and band gap photoemission study of (1 1 1) In2O3 epitaxial films under interactions with oxygen, water and carbon monoxide

Synchrotron radiation ultraviolet photoemission experiments at photon energies of 150 and 49 eV were performed on an epitaxial layer of (1 1 1) In₂O₃ with good crystallinity as established by a standard scanning probe and diffraction methods. Valence band (VB) and band gap photoemission spectra were monitored under separate oxygen, water and carbon monoxide exposures (100 L) at different activation temperatures within the range utilized for chemiresistive gas sensors (160-450 °C). Large changes in photoemission response within the whole VB were observed for all gases. Regular shifts of the valence band edge relative to the Fermi energy were found under gas exposures on two kinds of surface (partially reduced or partially oxidized), and are interpreted as changes of surface potential. Treatments in oxygen resulted in upward band bending (∼0.5 eV at T = 320 °C). Regardless of activation temperature, treatments in water resulted in downward band bending, but with small changes (<0.1 eV). Reduction properties of carbon monoxide were observed only at high temperatures of T ? 370 °C. At temperatures of 160 and 250 °C unusual “oxidizing” behavior of CO was observed with upward band bending of ∼0.7 eV (160 °C). Oxidizing and reducing effects of the gas interactions with the (1 1 1) In₂O₃ surface in all cases were accompanied by a corresponding behavior, i.e., a decrease or increase in photoemission response from so-called defect states in the band gap near the top of the valence band. The increases of photoemission within a band gap with maxima at binding energies (BE) of 0.4 (O₂-induced peak) and 1.0 eV (CO-induced peak) were, respectively, found for interactions with O₂ and CO for low temperatures (T = 160 and 250 °C). These responses were ascribed to acceptor-like electronic levels of O₂ and CO chemisorption states, respectively. A definite split of the top VB peak (BE ∼ 4.0 eV) was found under CO dosing at 160 °C. Established knowledge of the CO interaction with the (1 1 1) In₂O₃ surface explains earlier revealed acceptor-like behavior of In₂O₃ film conductivity during CO detection at operational temperatures lower than 250 °C through the formation of acceptor-like electronic levels of adsorbed CO molecules.     

Annealing effect in glass woven fabric composites,Part II. Bending properties

Effects of annealing on bending properties of composites reinforced with plain glass woven fabrics that were treated with different concentrations of silane coupling agent were investigated in this paper. Bending strength increased by annealing in the specimen treated with lower silane concentration. Higher annealing temperature in a range from 80°C to 150°C led to higher bending strength. Then, the fracture mode changed from a micro-crack type (low strength type) to a branched matrix crack type (high strength type) by annealing.     

Design equations for the assessment and FRP-strengthening of reinforced rectangular concrete columns under combined biaxial bending and axial loads

A simple procedure is proposed for the assessment of reinforced rectangular concrete columns under combined biaxial bending and axial loads and for the design of a correct amount of FRP-strengthening for underdesigned concrete sections. Approximate closed-form equations are developed based on the load contour method originally proposed by Bresler for reinforced concrete sections. The 3D failure surface is approximated along its contours, at a constant axial load, by means of equations given as the sum of the acting/resisting moment ratio in the directions of principal axes of the sections, raised to a power depending on the axial load, the steel reinforcement ratio, and the section shape. The method is extended to FRP-strengthened sections. Moreover, to make it possible to apply the load contour method in a more practical way, simple closed-form equations are developed for rectangular reinforced concrete sections with a two-way steel reinforcement and FRP strengthenings on each side. A comparison between the approach proposed and the fiber method (which is considered exact) shows that the simplified equations correctly represent the section interaction diagram. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 44, No. 3, pp. 443–462, May–June, 2008.     

The ultimate state of polymeric materials and laminated and fibrous composites under asymmetric high-cycle loading

The prediction of the high-cycle fatigue strength of polymeric and composite materials in asymmetric loading is considered. The problem is solved on the basis of a nonlinear model of ultimate state allowing us to describe all typical forms of the diagrams of ultimate stresses. The material constants of the model are determined from the results of fatigue tests in symmetric reversed cycling, in a single fatigue test with the minimum stress equal to zero, and in a short-term strength test. The fatigue strength characteristics of some polymers, glass-fiber laminates, glass-fiber-reinforced plastics, organic-fiber-reinforced plastics, and wood laminates in asymmetric tension-compression, bending, and torsion have been calculated and approved experimentally. __________ Translated from Mekhanika Kompozitnykh Materialov, Vol. 44, No. 1, pp. 87–102, January–February, 2008.