含磷有机硅杂化环氧树脂固化体系性能研究

通过磷酸与γ-环氧丙氧基三甲氧基硅烷反应得到含磷有机硅氧烷,并加入到环氧树脂/4,4'-二氨基二苯基甲烷体系中混合,通过溶胶-凝胶的方法制备了含磷有机硅杂化环氧树脂固化物.对固化体系进行了玻璃化转变温度、热失重、阻燃、拉伸强度、冲击强度测试分析.结果表明,该固化体系的阻燃性得到提高,极限氧指数在25.8～29.3,玻璃化转变温度得到提高,在161～179℃;虽然初始分解温度比纯环氧树脂固化物低,但800℃残炭率可以达到26.5%,提高了36%;拉伸强度得到提高,在71～94 MPa,冲击强度可以达到14.36 kJ/m2,提高了14%.该固化体系具有较好的阻燃性能和热性能,同时具有较好的力学性能.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

Selective depiction of susceptibility transitions using Laplace-filtered phase maps

In this work, we aim to demonstrate the ability of Laplace-filtered three-dimensional (3D) phase maps to selectively depict the susceptibility transitions in an object. To realize this goal, it is first shown that both the Laplace derivative of the z component of the static magnetic field in an object and the Laplacian of the corresponding phase distribution may be expected to be zero in regions of constant or linearly varying susceptibility and to be nonzero when there is an abrupt change in susceptibility, for instance, at a single point, a ridge, an interface, an edge or a boundary. Next, a method is presented by which the Laplace derivative of a 3D phase map can be directly extracted from the complex data, without the need for phase unwrapping or subtraction of a reference image. The validity of this approach and of the theory behind it is subsequently demonstrated by simulations and phantom experiments with exactly known susceptibility distributions. Finally, the potential of the Laplace derivative analysis is illustrated by simulations with a Shepp-Logan digital brain phantom and experiments with a gel phantom containing positive and negative focal susceptibility deviations.     

A unique approach to accurately measure thickness in thick multilayers

X‐ray optics called multilayer Laue lenses (MLLs) provide a promising path to focusing hard X‐rays with high focusing efficiency at a resolution between 5 nm and 20 nm. MLLs consist of thousands of depth‐graded thin layers. The thickness of each layer obeys the linear zone plate law. X‐ray beamline tests have been performed on magnetron sputter‐deposited WSi₂/Si MLLs at the Advanced Photon Source/Center for Nanoscale Materials 26‐ID nanoprobe beamline. However, it is still very challenging to accurately grow each layer at the designed thickness during deposition; errors introduced during thickness measurements of thousands of layers lead to inaccurate MLL structures. Here, a new metrology approach that can accurately measure thickness by introducing regular marks on the cross section of thousands of layers using a focused ion beam is reported. This new measurement method is compared with a previous method. More accurate results are obtained using the new measurement approach.     

Influence of rare earth Ce on structural, electrical and magnetic properties of Sr based W-type hexagonal ferrites

A series of single phase W-type Sr_3−xCe_xFe₁₆O₂₇ (x=0, 0.02, 0.04, 0.06, 0.08, 0.10) hexagonal ferrites prepared by the Sol-Gel method was sintered at 1050 °C for 5 h. The X-ray diffraction analysis reveals that all the samples belong to the family of W-type hexagonal ferrites. The c/a ratio falls in the range of W-type hexagonal ferrites. The grain size was measured by SEM varies from 0.7684 to 0.4366 μm which shows that the Ce³⁺ substituted samples have smaller grain size than pure ferrite Sr₃Fe₁₆O₂₇ which results from the difference in ionic radii of Ce³⁺ (1.034 Å) and Sr²⁺ (1.12 Å). The room temperature resistivity of the present samples varies from 6.5×10⁸ to 272×10⁸ Ω-cm. The coercivity increases from 1370 to 1993 Oe which is consistent with the decrease in grain size. The coercivity values indicate that the present samples fall in the range of hard ferrites. The large value of H_c may be due to domain wall pinning at the grain boundaries.     

“最小二乘法变点冰水情数据处理算法”的研究与应用

将非线性统计学中的变点分析方法应用于基于空气、冰与水的物理特性差异实现冰水情自动检测过程的现场数据处理中,提出了利用被测物质物理参数的动态变点替代经验阈值来确定空气、冰与水界面位置的"最小二乘法变点冰水情数据处理算法",较好地解决了原始采样数据中奇异值引起误判的工程难题,提高了冰情数据分析的准确度.利用该算法对黄河河道现场冰水情采集数据进行分析,得到了较准确的结果,实现了对冰层生消全过程的自动监测.     

适用于金属薄板焊接的柔性光纤耦合半导体激光加工光源

研制了一种单光纤耦合的柔性半导体激光加工光源,该光源由20个传导热沉封装的激光列阵以线阵合束方式耦合而成,在大通道工业水冷条件下,从600 μm芯径、NA为0.2的光纤中连续输出907 W功率,输出光束质量为47 mm·mrad,最终达到工件表面的功率密度为3.21×10⁵ W/cm²,最大插头效率达39%。该激光光源具有直接应用在金属薄板焊接的潜力。     

核实验数据获取系统中的触发信号预处理

简要介绍了在核物理实验数据获取系统中,用FPGA芯片和VHDL语言实现对事件触发信号的预处理。阐述了在核物理实验数据获取系统中对事件触发信号的一般要求; 结合60Co伽马谱测量实验,介绍了基于一套自主研发的数据获取系统中触发信号的预处理,并给出了用VHDL语言实现该触发信号预处理的思想、仿真时序图和实验结果。该方法通过实验验证,证明切实可行,灵活性强。     

简并四波混频实现全光信号幅度整形的系统设计

对光纤中简并四波混频(DFWM)耦合波方程进行数值求解,通过分析发现:泵浦光功率的增大会导致泵浦光与反斯托克斯光之间能量交换周期减小。阐述了优化光纤中DFWM实现全光信号幅度整形的机理。在此基础上设计了一个优化的全光信号幅度整形系统,并进行了系统仿真,结果表明:通过再生系统后,信号的消光比从9.46 dB提升到30.40 dB,品质因子从15.95提升到了180.40。     

超光滑加工的后置处理算法研究

为了精确控制超光滑加工过程中磨头的运动轨迹,从而实现光学元件材料去除的均匀稳定,研究了超光滑加工的后置处理算法。分析了超光滑加工工艺的特点和相应的超光滑机床的机械结构,建立了机床的坐标系统,构造了机床的运动学模型。对于光学元件母线为任意平面曲线的情况,研究了磨头运动轨迹的等误差直线逼近算法。在曲率半径为290mm,相对口径为1∶2.9的凹球面上进行了超光滑加工实验。结果表明,利用所述算法可以精确地控制磨头的运动轨迹,从而保证材料去除的稳定性。