测量行波管电子注的法拉第筒的热分析

利用ANSYS软件对测量行波管电子注截面的法拉第筒探头进行了热分析研究.分析了在单脉冲情况下,测量各种直径的不同脉冲功率密度的电子注、不同脉冲宽度对法拉第筒温度的影响,研究了测量不同功率密度的电子注可以使用的脉冲宽度.结果表明,仅法拉第筒上的注斑区域温度迅速上升,温度梯度较大,其它部分温度基本不变,为保证法拉第筒能够持...     

Site-specific ϕ- and ψ-torsion angle determination in a uniformly/extensively 13C- and 15N-labeled peptide

A solid-state rotational-echo double resonance (REDOR) NMR method was introduced to identify the ?- and ψ-torsion angle from a ¹H–¹⁵N or ¹H–¹³C′ spin system of alanine-like residues in a selectively, uniformly, or extensively ¹⁵N-/¹³C-labeled peptide. When a C_α(i) or a ¹⁵N peak is site-specifically obtainable in the NMR spectrum of a uniformly ¹⁵N/¹³C-labeled sample system, the ψ- or ?-torsion angle specified by the conformational structure of peptide geometry involving ¹⁵N(i)–¹H_αi–¹⁵N(i + 1) or ¹³C′(i − 1)–¹H^Ni–¹³C′(i) spin system can be identified based on ¹³C_α- or ¹⁵N-detected ¹H_α–¹⁵N or ¹H_N–¹³C REDOR experiment. This method will conveniently be utilized to identify major secondary motifs, such as α-helix, β-sheet, and β-turn, from a uniformly ¹⁵N-/¹³C-labled peptide sample system. When tested on a ¹³C-/¹⁵N-labeled model system of a three amino acid peptide Gly–[U–¹³C, ¹⁵N]Ala–[U–¹³C, ¹⁵N]Leu, the ψ-angle of alanine obtained experimentally, ψ = −40 ± 30°, agreed reasonably well with the X-ray determined angle, ψ = −39°.     

n,p柱宽度对超结SiGe功率二极管电学特性的影响

结合SiGe材料的优异性能与超结结构在功率器件方面的优势,提出了一种超结SiGe功率二极管.该器件有两个重要特点:一是由轻掺杂的p型柱和n型柱相互交替形成超结结构,取代传统功率二极管的n^-基区;二是阳极p⁺区采用很薄的应变SiGe材料.该二极管可以克服常规Si p⁺n^-n⁺功率二极管存在的一些缺陷,如阻断电压增大的同时,正向导通压降随之增大,反向恢复时间也变长.利用二维器件模拟软件MEDICI仿真 关键词： 超结 锗硅二极管 n p柱宽度 电学特性     

Microstructure and surface mechanical properties of pulse electrodeposited nickel

The surface of carbon steel was modified by electrochemical deposition of Ni in a standard Watt's bath using dc and pulse plating electrodeposition. The aim was to compare the microstructure and surface mechanical properties of the deposit obtained by both techniques. Materials characterization was conducted using field emission scanning electron microscope fitted with scanning transmission electron detector, atomic force microscope and X-ray diffractometer. Nanoindentation hardness, elastic modulus, adhesion, coefficients of friction and wear rates were determined for both dc and pulse electrodeposits. Experimental results indicate that pulse electrodeposition produced finer Ni grains compared to dc plating. Size of Ni grains increased with deposition. Both dc and pulse deposition resulted in grain growth in preferred (2 0 0) orientation. However, presence of Ni (1 1 1) grains increased in deposits produced by pulse deposition. Pulse plated Ni exhibited higher hardness, creep and coefficient of friction and lower modulus of elasticity compared to dc plated Ni.     

A novel method for improving the adhesion strength of the electrodeposited Ni films in MEMS

Adhesion performance of MEMS materials is increasingly important with the widely use of miniaturized devices. This paper proposed a novel method for improving adhesion performance between electrodeposited Ni multi-layers. The new method is to treat the Ni substrate in nickel chloride plating solution by pulse reverse current technique before electrodeposition. The dense oxide film of Ni substrate can be removed effectively by this electrochemical method, meanwhile, the proper roughness of Ni substrate is in favor of epitaxial growth during electrodeposition. Moreover, the Ni film is electrodeposited by the new method with low stress and coarse crystal grain. Consequently, the adhesion performance of Ni films is improved dramatically. The experimental results show that the adhesion performance of Ni film electrodeposited by the new method is about 3 times that of by traditional method.     

Effect of the laser fluence on the surface characterization of β-FeSi2 films prepared by pulsed laser deposition

Single-phase β-FeSi₂ films on silicon (1 0 0) were fabricated by pulse laser deposition. The structure and crystal quality of the samples were characterized by X-ray diffraction and Fourier transform infrared spectroscopy. The field scanning electron microscopy showed that the film thickness increases with the increasing of the laser fluence. Moreover, atomic force microscopy observations revealed the changes of surface properties with different laser fluence. Based upon all experimental results, it is found that 7 J/cm² is the most favorable for the formation of β-FeSi₂ thin films.     

叶片锯齿尾缘对降低空调室外机气动噪声影响的试验研究

依据现有的叶片尾迹宽度计算公式,计算了一空调室外机风机叶片的尾迹宽度,然后,以此尾迹宽度为参考基准,设计了两组不同形状和大小的锯齿形叶片尾缘,制作并试验研究了锯齿形尾缘对风机气动噪声的影响规律。结果表明,锯齿尾缘有明显降噪效果,正弦形锯齿较正三角形更好。锯齿尾缘通过降低宽频噪声降噪,而对离散噪声影响很小。采用与叶片尾迹...     

微槽道内气体流动特性的实验研究

搭建了微槽道的单相实验台,分析了氮气在不同深／宽比、长径比及水力直径的微槽道中流动特性。层流区的摩擦常数与理论预测值吻合较好（除L=20mm工况）,层流到湍流的转捩均有不同程度的提前（转捩Re数在1000左右）;在湍流区,槽道的长径比变小、相对粗糙度的增大（或水力直径的减小）及长度的减小可使流动阻力增大;拟合出了湍流区...