DESIGN OF A NOVEL 2-D UNIPLANAR CRLH-TL STRUCTURE

A novel uniplanar 2-D composite right/left-handed transmission line (CRLH-TL) structure is proposed based on a general transmission line theory and the way to increase the relative operating bandwidth in the left-handed (LH) region and lower the LH operating frequency is illustrated. In addition, a new method to extract parameters and calculate the Bloch impedance of the structure is presented. Numerical results of the dispersion as well as the extracted parameters are given, which are calculated based on full-wave simulation. The present 2-D uniplanar CRLH-TL structure is applicable to 2-D left-handed materials in lower and wider LH frequency range. Supported by the National Natural Science Foundation of China (No. 60371010) (No. 60471037) (No. 63531020)     

书籍扫描图像畸变参数自动计算方法的研究

为实现书籍扫描图像的畸变自动校正,提出用多项式来描述各像素的理论灰度g(zi)与页面上对应点到扫描仪工作平面距离zi二者之间的关系。为确立该多项式,在畸变参数已知条件下扫描一幅图像,根据已知畸变参数求出zi,即可按最小二乘法原理由各像素灰度的实际值求出多项式的各个系数。实验证明,采用4阶多项式已能满足一般要求,并求出了各系数。对任意扫描图像,自动计算畸变参数的方法为:首先利用扫描图像上页边空白处各像素的灰度,对畸变参数进行估计,并求出zi的估计值;然后代入所确立的多项式,可求得g(zi);通过调整各畸变参数的估计值,直到g(zi)与gi最为接近,即得最佳畸变参数。用于图像校正实验,获得了较好的校正效果,最大误差由不校正时的41%下降到了6.9%。这使得无需用户测量并输入有关畸变参数即可进行自动校正。     

一个组合分布模型及其参数估计

本文根据极值分布理论,提出了一个由原始分布和尾分布组成的组合分布模型,研究了组合分布模型中原始分布和尾分布的确定方法,建立了组合分布模型参数估计的加权最优化模型,实例计算说明,组合分布较好地反映了风险变量极值事件的风险。     

Precise lattice parameter measurements in CsCl-Br solid solutions between room temperature and 90°K by powder x-ray diffraction

Solid solutions of CsCl-Br in five different concentrations were prepared in sealed quartz tubes by heating the mixture to 1123°K for 6–8 hr and quenching to room temperature. X-ray diffractograms were taken at eight different temperatures between room temperature and 90°K for these solid solutions using the YPC50NM powder diffractometer and a continuous flow cryostat. The observed lattice parameters for each sample at each temperature obtained from the powder diffractograms were then extrapolated to give the true lattice parameters using the least square method with Nelson-Riley extrapolation scheme. The values of the true lattice parameters at each concentration and at each temperature were tabulated and the results discussed. It is shown that the lattice parameters vs temperature for some concentrations exhibit an anomalous behaviour. Contribution No. 691     

Adaptive Interpolation by Scaled Multiquadrics

We present an adaptive method to extract shape-preserving information from a univariate data sample. The behavior of the signal is obtained by interpolating at adaptively selected few data points by a linear combination of multiquadrics with variable scaling parameters. On the theoretical side, we give a sufficient condition for existence of the scaled multiquadric interpolant. On the practical side, we give various examples to show the applicability of the method.     

散射体系A+BC的平-振能量传递

用Alhassid与Levine所提出的动力学李代数的方法(简称A-L理论),研究了含有二级非简谐的共线散射体系A+BC的平-振能量传递问题,计算了散射过程含有主要动力学参量的跃迁矩阵和跃迁几率的解析表示式.     

The Ring of Invariants of Three (3 × 3)-Matrices over a Field of Prime Characteristic

We find a minimal system of generators and a homogeneous system of parameters for the algebra of invariants of three matrices of third order over a field of an arbitrary characteristic.     

Activation energies for metastable to stable phase transition of 4,4'-di-n-heptyl- oxyazoxybenzene

Complexes of adenine, AdH, with cobalt, nickel and copper chlorides were prepared and their thermodynamic functions were determined. The complexing processes are endothermic in nature. The thermal behaviour of complexes was followed up by using TG and DTA analyses. The stoichiometry of thermal decomposition of the investigated complexes was suggested. This revised version was published online in August 2006 with corrections to the Cover Date.     

Sterically stabilized emulsion polymerization of styrene: Pseudo‐semicontinuous approach

The sterically stabilized emulsion polymerization of styrene initiated by a water‐soluble initiator at different temperatures has been investigated. The rate of polymerization (R_p) versus conversion curve shows the two non‐stationary‐rate intervals typical for the polymerization proceeding under non‐stationary‐state conditions. The shape of the R_p versus conversion curve results from two opposite effects—the increased number of particles and the decreased monomer concentration at reaction loci as the polymerization advances. At elevated temperatures the monomer emulsion equilibrates to a two‐phase or three‐phase system. The upper phase is transparent (monomer), and the lower one is blue colored, typical for microemulsion. After stirring such a multiphase system and initiation of polymerization, the initial coarse polymer emulsion was formed. The average size of monomer/polymer particles strongly decreased up to about 40% conversion and then leveled off. The initial large particles are assumed to be highly monomer‐swollen particles formed by the heteroagglomeration of unstable polymer particles and monomer droplets. The size of the “highly monomer” swollen particles continuously decreases with conversion, and they merge with the growing particles at about 40–50% conversion. The monomer droplets and/or large highly monomer‐swollen polymer particles also serve as a reservoir of monomer and emulsifier. The continuous release of nonionic (hydrophobic) emulsifier from the monomer phase increases the colloidal stability of primary particles and the number of polymer particles, that is, the particle nucleation is shifted to the higher conversion region. Variations of the square and cube of the mean droplet radius with aging time indicate that neither the coalescence nor the Ostwald ripening is the main driving force for the droplet instability. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 804–820, 2003     

Sensitivity of trust-region algorithms to their parameters

In this paper, we examine the sensitivity of trust-region algorithms on the parameters related to the step acceptance and update of the trust region. We show, in the context of unconstrained programming, that the numerical efficiency of these algorithms can easily be improved by choosing appropriate parameters. Recommended ranges of values for these parameters are exhibited on the basis of extensive numerical tests. MSC classification: 65K05, 90C26, 90C30