Deprotonation of chloropyridines using lithium magnesates

4-Chloropyridine was deprotonated on treatment with 1/3 equiv of the highly coordinated magnesate Bu₃(TMP)MgLi₂ in THF at −10 °C, as evidenced by trapping with I₂. The use of Bu(TMP)₂MgLi in Et₂O allowed the reaction of 2-chloropyridine, giving the 3-functionalized derivative as the main product. Mixtures of 3- and 4-functionalized derivatives were obtained when 2,6-dichloropyridine was involved in the reaction. Performing the reaction on 3-chloropyridine with lithium magnesates in THF, either the 4,4′-dimer or the 4-iodo derivative was formed after quenching by I₂, the former using 1/3 equiv of Bu₂(TMP)MgLi and the latter using 1 equiv of (TMP)₃MgLi. Similar results were observed with 3,5-dichloropyridine, 2,5-dichloropyridine and 3-chloro-2-fluoropyridine. 1,2-Migration of the lithium arylmagnesate formed by deprotonation was proposed to justify the dimers formation.     

Flow injection determination of bismuth in urine by successive retention of Bi(III) and tetrahydroborate(III) on an anion-exchange resin and hydride generation atomic absorption spectrometry

Bismuth as BiCl₄⁻ and BH₄⁻ ware successively retained in a column (150 mm × 4 mm, length × i.d.) packed with Amberlite IRA-410 (strong anion-exchange resin). This was followed by passage of an injected slug of hydrochloric acid resulting in bismuthine generation (BiH₃). BiH₃ was stripped from the eluent solution by the addition of a nitrogen flow and the bulk phases were separated in a gas–liquid separator. Finally, bismutine was atomized in a quartz tube for the subsequent detection of bismuth by atomic absorption spectrometry. Different halide complexes of bismuth (namely, BiBr₄⁻, BiI₄⁻ and BiCl₄⁻) were tested for its pre-concentration, being the chloride complexes which produced the best results. Therefore, a concentration of 0.3 mol l⁻¹ of HCl was added to the samples and calibration solutions. A linear response was obtained between the detection limit (3σ) of 0.225 and 80 μg l⁻¹. The R.S.D.% (n = 10) for a solution containing 50 μg l⁻¹ of Bi was 0.85%. The tolerance of the system to interferences was evaluated by investigating the effect of the following ions: Cu²⁺, Co²⁺, Ni²⁺, Fe³⁺, Cd²⁺, Pb²⁺, Hg²⁺, Zn²⁺, and Mg²⁺. The most severe depression was caused by Hg²⁺, which at 60 mg l⁻¹ caused a 5% depression on the signal. For the other cations, concentrations between 1000 and 10,000 mg l⁻¹ could be tolerated. The system was applied to the determination of Bi in urine of patients under therapy with bismuth subcitrate. The recovery of spikes of 5 and 50 μg l⁻¹ of Bi added to the samples prior to digestion with HNO₃ and H₂O₂ was in satisfactory ranges from 95.0 to 101.0%. The concentrations of bismuth found in six selected samples using this procedure were in good agreement with those obtained by an alternative technique (ETAAS). Finally, the concentration of Bi determined in urine before and after 3 days of treatment were 1.94 ± 1.26 and 9.02 ± 5.82 μg l⁻¹, respectively.     

Nonclassical titanocene silyl hydrides

The titanocene silyl hydride complexes [Ti(Cp)2(PMe3)(H)(SiR3)] [SiR3=SiMePhCl (6), SiPh2Cl (7), SiMeCl2 (8), SiCl3 (9)] were prepared by HSiR3 addition to [Ti(Cp)2(PMe3)2] and were studied by NMR and IR spectroscopy, X-ray diffraction (for 6, 8, and 9), and DFT calculations. Spectroscopic and structural data established that these complexes exhibit nonclassical Ti-H-Si-Cl interligand hypervalent interactions. In particular, the observation of silicon-hydride coupling constants J(Si,H) in 6-9 in the range 22-40 Hz, the signs of which we found to be negative for 8 and 9, is conclusive evidence of the presence of a direct Si-H bond. The analogous reaction of [Ti(Cp)2(PMe3)2] with HSi(OEt)3 does not afford the expected classical silyl hydride complex [Ti(Cp)2(PMe3)(H)[Si(OEt)3]], and instead NMR-silent titanium (apparently TiIII) complex(es) and the silane redistribution product Si(OEt)4 are formed. The structural data and DFT calculations for the compounds [Ti(Cp)2(PMe3)(H)(SiR3)] show that the strength of interligand hypervalent interactions in the chlorosilyl complexes decreases as the number of chloro groups on silicon increases. However, in the absence of an Si-bound electron-withdrawing group trans to the Si-H moiety, a silane sigma complex is formed, characterized by a long Ti-Si bond of 2.658 A and short Si-H contact of 1.840 A in the model complex [Ti(Cp)2(PMe3)(H)(SiMe3)]. Both the silane sigma complexes and silyl hydride complexes with interligand hypervalent interactions exhibit bond paths between the silicon and hydride atoms in Atoms in Molecules (AIM) studies. To date a classical titanocene phosphane silyl hydride complex without any Si-H interaction has not been observed, and therefore titanocene silyl hydrides are, depending on the nature of the R groups on Si, either silane sigma complexes or compounds with an interligand hypervalent interaction.     

The reactivity of N,N-dialkyl-N-(3-phenylsulfinyltetrahydrofuran-2-ylidene)ammonium bromide

trans-Stereoselective electrophilic cyclization of (2R*,SS*)-N, N-diisopropyl-2-phenylsulfinylpent-4-enamide under the action of bromine afforded (3R*,5S*, SS*)-N-(5-bromomethyl-3-phenylsulfinyltetrahydrofuran-2-ylidene)-N,N-diisopropylammonium bromide. Its transformations under the conditions of hydrolysis, dehydrobromination, and hydride reduction were studied. Dedicated to Academician V. A. Tartakovsky on the occasion of his 75th birthday. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 8, pp. 1485–1490, August, 2007.     

Gas-chromatographic analysis of carbides in aluminium and magnesium

Summary A quantitative gas-chromatographic method (molecular sieve column, FID) for the determination of Al₄C₃ in aluminium and magnesium has been developed. The effect of methane from external sources has been investigated and eliminated. Metallographic analysis of carbides in polished specimens were consistent with the gas-chromatographic measurements within a factor of 2. The discrepancy can be explained by the large uncertainties in light microscopy analysis of the small carbides. Analysis of commercial magnesium shows that the metal contains ca. 2–9 ppm of Al₄C₃. The concentration of carbides in aluminium from the electrolysis cell is in the range of 10–35 ppm and in the final product of ca. 2–12 ppm Al₄C₃. CaC₂ has been detected in a few magnesium and aluminium samples by means of gas-chromatography and microprobe analysis.

---

Gas-chromatographische Analyse von Carbiden in Aluminium und Magnesium

Zusammenfassung Zur Bestimmung von Al₄C₃ in Aluminium und Magnesium wurde eine quantitative gas-chromatographische Methode (MolekularsiebSäule, FID) entwickelt. Der Einfluß von Methan aus äußeren Quellen, wurde untersucht und ausgeschaltet. Die metallographischen Untersuchungen von Carbiden an polierten Proben stimmten mit den Ergebnissen der gas-chromatographischen Messungen mit einem Faktor von 2 überein. Der Unterschied kann durch die großen Unsicherheiten bei der lichtmikroskopischen Analyse der kleinen Carbide erklärt werden. Die Analyse des technisch reinen Magnesiums zeigt, daß das Metall ca. 2–9 ppm Al₄C₃ enthält. Die Konzentration von Carbiden in elektrolytisch raffiniertem Aluminium liegt im Bereich 10–35 ppm und im Endprodukt bei ca. 2–12 ppm Al₄C₃. CaC₂ wurde in einigen Magnesium- und Aluminiumproben mit Hilfe von gas-chromatographischen und Mikrosondenuntersuchungen festgestellt.

     

On‐Line Determination of Arsenic Species in Sea Water by Selective Hydride Generation Coupled with Inductively Coupled Plasma — Mass Spectrometry

A method for direct de termination of total in organic arsenic (III+V), arsenic (III) and dimethylarsinate (DMA) in sea water was developed by combining continuous‐flow selective hydride generation and inductively coupled plasma mass spectrometry (ICP‐MS) is presented. The principle underlying selective hydride generation is based on proper control of the reaction conditions for achieving separation of the respective arsenic species. The effects of pH and composition of reaction media on mutual interference between the arsenic species were investigated in detail. The results indicate that the appropriate media for the selective determination of total in organic arsenic, DMA and As(III) are 6 M HNO₃, acetate buffer at pH = 4.63 and citrate buffer at pH = 6.54, respectively. The concentrations of total inorganic arsenic species, As(III+V), and As(III) were respectively deter mined and that of As(V) was obtained by the difference between them. As to the concentration of DMA, it was obtained after correction from the interference caused by As(III) and As(V). By following the established procedure, the detection lim its (as based on 3‐sigma criterion) for As(III+V), As(III) and DMA were 0.050, 0.009, and 0.002 ng/mL, respectively. There liability of the pro posed method was evaluated in terms of precision and spike addition. The results indicated that the precision of better than 3% and spike recovery of 95 to 105% for all the arsenic species tested in the natural sea water samples can be obtained.     

Insertion Reactions of Carbon Disulfide into Mg‐C and Mg‐N Bonds: Syntheses and Structural Determinations of Mg(S2CY)2(THF)n(Y=NEt2, NiPr2, iPr,Ph) and BrMg(S2CZ)(THF)3(Z=Ph,iPr)

The insertion reaction of CS₂ with Mg(NR₂)₂ (R= Et, ⁱPr), MgR′₂ (R′= Et, Ph) and R″MgBr (R″= ⁱPr, Ph) respectively lead solid products, Mg(S₂CNR₂)₂(THF)_n ( 1 : R= Et, n=2; 2 : R= ⁱPr, n=1), Mg(S₂C′R)₂(THF)₂ ( 3 : ′R= Et, 4 : ′R= Ph), BrMg(S₂C″R) (THF)₃ ( 5 : ″R= ⁱPr, 6 : ″R= Ph) in which the inserted carbon disulfides act as terminal chelating ligands. These compounds were characterized with ¹H, ¹³C NMR, IR spectroscopy, mass spectrometry, elemental analyses, and X‐ray crystallography.     

Structural Patterns and Dimensionality in Magnesium Borophosphates: The Crystal Structures of Mg2(H2O)[BP3O9(OH)4] and Mg(H2O)2[B2P2O8(OH)2]·H2O

Hydrothermal investigations in the system MgO/B₂O₃/P₂O₅(/H₂O) yielded two new magnesium borophosphates, Mg₂(H₂O)[BP₃O₉(OH)₄] and Mg(H₂O)₂[B₂P₂O₈(OH)₂]·H₂O. The crystal structures were solved by means of single crystal X‐ray diffraction. While the acentric crystal structure of Mg₂(H₂O)[BP₃O₉(OH)₄] (orthorhombic, P2₁2₁2₁ (No. 19), a = 709.44(5) pm, b = 859.70(4) pm, c = 1635.1(1) pm, V = 997.3(3) × 10⁶ pm³, Z = 4) contains 1D infinite chains of magnesium coordination octahedra interconnected by a borophosphate tetramer, Mg(H₂O)₂[B₂P₂O₈(OH)₂]·H₂O (monoclinic, P2₁/c (No. 14), a = 776.04(5) pm, b = 1464.26(9) pm, c = 824.10(4) pm, β = 90.25(1)°, V = 936.44(9) × 10⁶ pm³,Z = 4) represents the first layered borophosphate with 6³ net topology. The structures are discussed and classified in terms of structural systematics.     

Conductivity as a Sensor for Monitoring Relative Magnesium Corrosion Rates in Real‐time,in Serum‐containing Media under Cell Culture Conditions

Because controlling the corrosion rate of magnesium metal will be crucial to the success of biomedical implants containing pure magnesium or magnesium alloys, many ways have been sought to improve in vitro tests to analyze corrosion rates, and also to identify new methods of preparing or post‐processing magnesium. In this work, for an in vitro assay, we explored the use of a commercially available conductivity sensor to study magnesium corrosion under cell culture conditions that duplicate many physiologically appropriate parameters. With this sensor, we studied the corrosion of two previously untested magnesium single crystal samples that differed in surface treatments that could alter corrosion rates. The results show that the relative conductivity changes in (mS/cm) over the total time of immersion were proportional to the corrosion rates in (mm/y) and also to the total magnesium released, as detected by inductively coupled plasma mass spectrometry (ICP‐MS).