Metal Oxide Thin Films Containing Au Nano-Particles Prepared with Gas Diffusion Method

Au particles dispersed thin metal oxide films were prepared from precursor films containing HAuCl₄ with H₂S gas diffusion method. HAuCl₄ was uniformly dissolved in the films as promoted by hydroxypropyl cellulose (HPC). The mechanism of the Au particle formation was studied. It was found that HAuCl₄ was converted directly to Au metal particles upon contacting with H₂S gas. Au particles generated by this method were characterized with small particle size, sharp size distribution and high volume fraction in the films. The surface plasma resonance absorption of Au particles shifted to longer wavelength when TiO₂ component was introduced in the matrix.     

Effect of the protonation level of poly(o-phenylenediamine) (PoPD) on the ac impedance of humidity-sensitive PoPD/poly(vinyl alcohol) composite film

A composite film consisting of poly(o-phenylenediamine) (PoPD) and poly(vinyl alcohol) (PVA) has been prepared, and the effect of the protonation level of PoPD on the response of the composite to humidity been investigated by ac impedance measurements. The electrochemical system of the PoPD/PVA composite in a humid atmosphere is represented by an electrochemical equivalent circuit containing film (R_film, C_film), Warburg (W) and interfacial (R_ct, C_dl) impedance. R_film was increased with decreasing protonation level of the PoPD in relative humidity regions higher than 40%, but it was almost independent of the protonation level in humidity regions lower than this percentage.     

Cu-Mg/Al复合氧化物催化碳颗粒物燃烧性能的研究

恒定二价与三价阳离子比为3(nM2+/nM3+=3),采用共沉淀法制备不同Cu含量的系列水滑石前驱物, 800 ℃焙烧4 h形成复合氧化物(CuO质量百分数分别为0％、5％、10％、15％、20％、30％、40％)用作柴油车排放碳颗粒物燃烧的催化剂,并采用XRD、BET、TG-DSC、FT-IR、TPR等表征手段研究了Cu、Mg含量对材料前驱物物化性能的影响及对其衍生复合氧化物催化碳颗粒物燃烧性能的影响．结果表明,Cu、Mg含量对材料的热稳定性、比表面和催化氧化活性有显著的影响. Mg有助于提高催化剂的热稳定性; Cu含量增加,催化剂比表面下降,但比表面不是影响催化剂活性的主要因素. CuO含量为15％时,催化剂具有最好的催化活性和稳定性,碳颗粒物的起燃温度(T10)和半转化温度(T50)分别为336 ℃和409 ℃.在CuO含量≤30％时可以形成结构完整的水滑石前驱物, CuO含量为40％时出现Cu(OH)2杂相; CuO含量< 20％时,经高温焙烧可得到均匀的复合氧化物, CuO含量≥20％时出现CuO偏析． TPR结果表明焙烧温度和复合氧化物的组成决定了材料的可还原性能．     

羧基丙烯酸酯涂料合成及其防雾性能研究

采用种子乳液聚合法合成了一种互穿网络型羧基丙烯酸酯类聚物乳液，研究了加料方式对羧基分布的影响，结果表明丙烯酸加入到核单体中有利于羧基分布在乳胶粒表面。在体系中引入离子键交联结构提高了乳液涂料的硬度和耐水性能，离子键交联ＰＩＬＮ型涂料具有优良的防雾性能。     

Influence of pH on formation and stability of phosphatidylcholine/phosphatidylserine coatings in fused-silica capillaries

The effect of pH on the formation and stability of phospholipid coatings in fused-silica capillaries in electrophoresis was investigated. A liposome solution consisting of 3 mM of 80:20 mol% phosphatidylcholine/phosphatidylserine (PC/PS) in N-(2-hydroxyethyl)piperazine-N'-(2-ethanesulfonic acid) (HEPES) buffer was used as coating material. The coating was prepared by a method described earlier and five steroids were used as neutral model analytes. First, the effect of pH of the coating solution on the formation and stability of phospholipid coatings was studied at pH 6.5-8.5. The pH of the background electrolyte (BGE) solution (HEPES) was either kept constant at pH 7.4 or made similar to the pH of the liposome coating solution. Results showed that attachment of the coating on the fused-silica wall mostly depends on the protonation of amines of the phospholipids and HEPES. The ability of the phospholipid coating to withstand changes in pH was then investigated by coating at pH 7.5 and separating steroids with acetic acid, 3-(cyclohexylamino)-1-propanesulfonic acid (CAPS), HEPES, or glycine BGE, adjusted to pH between 4.5 and 10.8. The results showed that with use of BGE solution at pH 10.8, the separation of steroids was not successful and the electroosmotic flow was high because of leakage of the phospholipid coating during preconditioning of the capillary with BGE solution. There was no phospholipid leakage with a BGE solution of pH 4.5, indicating that the protonated form of the functional groups of PS and HEPES participating in the attachment of the phospholipid coating to the capillary play an essential role in the success of the coating.     

Enhancement of the static SIMS secondary ion yields of lipid moieties by ultrathin gold coating of aged oil paint surfaces

Static secondary ion mass spectrometry (SIMS) is a powerful technique for identification and localization of pigments and binding media present in traditional paintings. Coating the surface of a cross‐section with a 20 Å thick gold layer improves the yields of secondary ions from the fatty acids and diacids. A chalk tablet containing 1% stearic acid, which was partially covered during gold deposition, is used as a test system to investigate the increase of the organic secondary ion yields upon gold deposition in SIMS imaging. A comparative study of a native and gold‐coated aged surface of a lead white‐containing linseed oil paint demonstrates the enhancement of the organic ion yields on a sample relevant for painting studies. The yields of oil paint‐derived negative ions increase by a factor of 3 whereas the yields of positive ions increase by a factor of 2–4. The different types of charged functional groups determine the degree of improvement in yield. Gold coating improves the ionization process of the fatty acids and does not influence their fragmentation. The dissociation of the lead white by the primary ion beam is reduced due to the gold coating. Copyright © 2004 John Wiley & Sons, Ltd.     

Electrochemical Characteristics of Mg0.9Ti0.1-xZrxNi （x=0.02, 0.04, 0.06） Alloys

Mg-based hydrogen storage alloys Mg0.9Ti0.1-xZrxNi (x=0.02, 0.04, 0.06) were successfully prepared by means of mechanical alloying (MA). The effects of Zr addition on the discharge capacity and the cycle performance of the Mg-based electrodes were also studied. It was found that the discharge capacities were improved with addition of a small amount of Zr and the cycle performances of the alloy were stabilized with the addition of Ti. The effects of surface modification or coating on the properties of Mg0.9Ti0.06Zr0.04Ni were also studied. The results indicated that coating with graphite improved both the discharge capacity and cycle life of the amorphous Mg0.9Ti0.06Zr0.04Ni electrode.     

Synthetic process to control the total size and component distribution of multilayer magnetic composite particles

A new synthetic process to prepare composite particles with multilayers, comprised of usual polymer latices, ultra-fine magnetic particles, and a polystyrene layer was examined under various solution conditions.First, the synthetic conditions of heterocoagulates, consisted of polystyrene latices (2a=180900 nm) and NiO·ZnO·Fe₂O₃ particles (2a=20 nm), were investigated as a function of medium pH, particle concentration, and particle size ratio, based on the concept of the heterocoagulation theory as applied by Harding et al. Regular heterocoagulates were generated under suitable medium and mixing conditions, and that their total size can be controlled by selecting the size of the original polymer latices used as the core.Second, the best encapsulation condition of the heterocoagulates via emulsion polymerization with polystyrene monomer was surveyed. The encapsulation of the heterocoagulates was greatly promoted by pretreatment with oleate molecules, although there is no tendency for the encapsulation when the surfactant-free bare heterocoagulates are used as the core.     

Preparation of thin SnO2 layers by inorganic sol-gel process

SnO₂ sols were prepared in the following way: (1) precipitation of metastannic acid with aqueous ammonia from aqueous solutions of SnCl₄, (2) washing the precipitates with NH₄NO₃ solution and water, (3) peptization of precipitates in water, sometimes with an addition of HNO₃, at elevated temperature using mechanical stirring. In those sols, sometimes diluted with water or ethanol, substrates (glass or silica derived wafers) were dipped and withdrawn at various rates. Gel coatings were converted into crystalline SnO₂ by thermal treatment at 600°C. Coatings with thickness between 300–2000 Å were prepared.     

Rapid and sensitive determination of ephedrine and pseudoephedrine by micellar electrokinetic chromatography with on-line regenerating covalent coating

A rapid, sensitive and reproducible micellar electrokinetic chromatographic method using hexamethyldisilazane as on-line regenerating covalent coating was developed for the quantification of ephedrine (E) and pseudoephedrine (PE). E and PE were derivatized with 4-chloro-7-nitrobenzo-2-oxa-1,3-diazol for laser-induced fluorescence detection. The on-line regenerating covalent coating formed a combinative double coating with the subsequently produced dynamic SDS coating. The total coating can be easily removed and conveniently regenerated on-line. The simple coating procedure was described. By a series of optimization, a running buffer of 20 mm Na(2)B(4)O(7) + 16 mm SDS was applied for the separation of the derivatives. Linear relationships for E and PE were obtained in the range of 0.044-6.60 microg mL(-1) (correlation coefficients: 0.9975 for E, 0.9981 for PE), and the detection limits for E and PE were 1.71 and 0.67 ng mL(-1), respectively. The separation speed, the reproducibility and the sensitivity were much improved over those of other capillary electrophoresis methods more recently reported. The method was applied to the analysis of the two alkaloids in traditional herbal preparations with recoveries in the range 92.8-104.8%.