High Power One- and Two-Order Cascaded Raman Lasers Based on Home-Made Phosphosilicate Fibre

One- and two-order cascaded Raman fibre lasers are demonstrated by using home-made P-doped Raman fibres.An output power of 2.8 W at 1245 nm with a slope efficiency of 33.4% and an output power of 2.0 W at 1495 nm with a slope efficiency of 23.5% are obtained with the pump source at 1069. 7nm.     

Antiphase State in Passively Q-Switched Yb：YAG Microchip Lasers with a Nd,Cr：YAG as Saturable Absorber

We experimentally investigate the antiphase dynamics phenomenon that occurs in a diode-pumped passively Q-switched Yb:YAG multimode laser with a Nd,Cr:YAG saturable absorber. Due to the effect of spatial hole burning, the multimode lasers with one, two, or three modes at different pump power are observed, and the pulses sequences display classic antiphase dynamics.     

A Movable-Cavity Cold Atom Space Clock

We present an experimental scheme of a cold atom space clock with a movable cavity. By using a single microwave cavity, we find that the clock has a significant advantage, i.e. the longitudinal cavity phase shift is eliminated. A theoretical analysis has been carried out in terms of the relation between the atomic transition probability and the velocity of the moving cavity by taking into account the velocity distribution of cold atoms. The requirements for the microwave power and its stability for atomic π/2 excitation at different moving velocities of the cavity lead to the determination of the proper working parameters of the rubidium clock in frequency accuracy 10^-17. Finally, the mechanical stability for the scheme is analysed and the ways of solving the possible mechanical instability of the device are proposed.     

Deformation Morphology underneath the Vickers Indent in Bulk Metallic Glasses

Plastic deformation behaviour of Zr52.5Al10Ni10Cu15Be12.5 and Mg65Cu25Gd10 bulk metallic glasses (BMGs) is studied by using the depth-sensing nanoindentation and microindentation. The subsurface plastic deformation zone of the BMGs is investigated using the bonded interface technique. Both the BMGs exhibit the serrated flow depending on the loading rate in the loading process of indentation. Slow indentation rates promote more conspicuous serrations, and rapid indentations suppress the serrated flow. Mg-based BMG shows a much higher critical loading rate for the disappearance of the serration than that in Zr-based BMG. The significant difference in the shear band pattern in the subsurface plastic deformation zone is responsible for the different deformation behaviour between the two BMGs. Increase of the loading rate can lead to the increase of the density of shear bands. However, there is no distinct change in the character of shear bands at the loading rate of as high as1000 nm/s.     

高功率固体激光器光学元件位相误差滤波

不同频段的位相误差对输出光束将产生不同的影响，低频段主要影响远场焦斑主斑的能量分布，中高频段影响光的散射或者可能出现的较大的强度峰值调制，高频段影响光的散射，导致能量的损失。研究光学元件引入的位相误差与输出光束之间的定性、定量关系，首先必须对位相误差进行相应的滤波处理，反映光学元件面形的细微误差。     

海洋激光雷达测量海中悬移质

研制了一套采用倍频YAG激光器的小型海洋激光雷达，用于测量海中悬移质浓度，2000年8月28日至9月5日，该系统安装于“东方红Ⅱ”号右舷下甲板，在渤海海区进行海中悬移质浓度现场测量，通过对18个站位的海洋激光雷达数据分析，获得的表层悬移质浓度与同步测量的海中悬移质浓度结果吻合较好。     

水平管外强化凝结传热的数值解

以Nusselt理论为基础,运用三维坐标建立了肋片侧面的冷凝传热模型,对肋片侧面的冷凝传热机理进行了分析,得出了肋片侧面表面传热系数的积分表达式。利用此法对水平环肋单管表面传热系数进行计算并将结果与传统解法进行比较。     

热丝加热电流对CH薄膜沉积速率和表面形貌的影响

 热丝辅助裂解法是结合气相沉积制备聚对二甲苯薄膜和热丝化学气相沉积而形成的一种制-CH薄膜的新方法。热丝辅助裂解法的最大特点就是在保持低衬底温度情况下可以获得高沉积速率，而热丝加热电流对薄膜沉积速率和薄膜表面形貌具有重要影响。研究表明，热丝加热电流越大，薄膜沉积速率越高，在加热电流9A时，薄膜沉积速率可达0.002mm/min，同时薄膜表面粗糙度随之增加，薄膜表面也开始出现其它元素污染，因此，一般热丝加热电流选择为7A附近。     

斐索梯度折射率光纤透镜传感实验

采用LD泵浦的单纵模Nd：YVO4倍频激光器、梯度折射率光纤透镜等器件构成斐索梯度折射率光纤透镜传感实验仪．本文介绍了实验装置和实验原理，并给出了实验结果。