Flammability studies of 3-methyl pyridine/water system

In industrial processes, information on the safety property of chemicals is essentially crucial for safe handling during unit operations. Ensuring the safe use of combustible or flammable substances in processes is unlikely without detailed investigations of their flammability characteristics and related hazards. We studied 3-methyl pyridine (3-picoline), e.g., flammability limits (LFL/UFL), maximum explosion pressure (P _max), maximum explosion pressure rise (dP/dt)_max, minimum oxygen concentration (MOC), vapor deflagration index (K _g), and characterized the influence of inert steam (H₂O) on critical parameters for 3-picoline/water mixtures at 270°C, 1 atm, various oxygen concentrations, and vapor mixing ratios (100/0, 30/70, 10/90 and 5/95 vol.%) with a 20-L-Apparatus in simulated conditions, respectively. The results showed that the flammability characteristics of 3-picoline_(aq) all increased with the oxygen concentration. However, as the composition of inert steam increased, the flammability parameters and the degree of fire and explosion hazards were significantly reduced, instead. This study elucidated the flammability properties of 3-picoline mixed with inert steam. The conclusions could be applied to proactively prevent the relevant processes from incurring fire and explosion accidents.     

The use of TG-FTIR technique for the assessment of hydrogen bromide emissions in the combustion of BFRs

The TG-FTIR technique was used in the present study to investigate the thermal degradation behaviour of materials containing brominated flame retardants under fire conditions. Time-temperature profiles and oxygen concentrations typical of selected fire scenarios were reproduced in the thermogravimetric analyzer, while the characterization of the gaseous products generated was performed by the simultaneous FTIR analysis. FTIR analysis combined with the use of specific calibration procedures allowed the quantitative estimation of the gaseous products evolved as a function of experimental conditions. The results obtained allowed the straightforward assessment and the comparison of the quantities of hydrogen bromide formed in the oxidation and thermal degradation of pure brominated flame retardants and of flame retarded materials of industrial interest. Hydrogen bromide yields resulted dependent on the experimental conditions used, such as oxygen concentration and heating rate. Although TG-FTIR experiments only provide a representation of the actual heterogeneous combustion products in real fire conditions, the coupled TG-FTIR technique proved to be a straightforward experimental methodology allowing one to obtain reference data on the nature and quantities of the macropollutants generated in a fire. This revised version was published online in July 2006 with corrections to the Cover Date.     

MICRO-PHASE SAEPARATION IN EPOXY RESIN WATERBORNE PARTICLES DURING CURING PROCESS

Sub-micron sized phenolic epoxy resin waterborne particles were prepared by phase inversion emulsification. Micro-phase separation occurred during the curing process at high temperature. The as-prepared samples possessed one glass transition temperature （Tg） and two exothermal processes during DSC heating scannings. After being thermally treated above the exothermal peak temperature, they possessed two glass transition temperatures with the disappearance of exothermal peaks, whilst a core/shell structure was formed. This was likely related with the outward diffusion of reactive oligomers to the outer layer of particles.     

The preparation of thick-film glass capillary columns

A detailed method for the routine preparation of glass capillary columns is presented. The method consists of coating a glass tube with quartz powder prior to pulling the tube into a capillary. The inner surface of the capillary consists of an even distribution of quartz particles fused to the walls. This surface has been found readily deactivated by standard procedures and ideal for the preparation of thick-film glass capillary columns. The method has been thoroughly tested in two independent laboratories to ensure that the procedures described are reproducible.     

Synthesis of Some Dialkyl Bromo-Substituted Benzyl Phosphonates

Arbuzov reaction of bromo-substituted benzyl bromides and trialkyl phosphites in benzene gave high yields of dialkyl bromo-substituted benzyl phosphonates, and —CH₂CH₂CH₂CH₃). The structural assignments of these phosphonates were confirmed by ¹H nmr, ¹³C nmr, ir and mass spectral analysis.     

N,N'-二(二乙氧基硫代磷酰基)-1,4-苯二胺的合成、晶体结构及热性能研究

通过二乙氧基硫代磷酰氯与对苯二胺反应生成了标题化合物N,N'-二(二乙氧基硫代磷酰基)-1,4-苯二胺，并应用元素分析, FTIR及¹H NMR对标题化合物进行了表征. 利用X射线单晶衍射测定了其晶体结构, 同时应用TG分析法对其热性能进行了分析. 标题化合物的相对分子质量M_r＝412.42, 为正交晶系, Pbca空间群, 晶胞参数为a＝0.86936(16) nm, b＝1.2787(2) nm, c＝1.8897(3) nm, β＝90°, V＝2.1006(7) nm³, Z＝8, D_c＝1.304 g/cm³, μ(Mo Kα)＝0.425 mm^－1, F(000)＝872, S＝1.052. 最终偏离因子R＝0.0628, wR＝0.1860, 可观测衍射点1852个[I＞2σ(I)]. 该晶体通过对苯二胺连接并以中心对称分布, 并形成层状结构, 且存在弱的分子内氢键N—H…S. TG分析表明该化合物有很好的热稳定性及成炭性, 通过其阻燃聚丙烯腈表明, 该物质是一种高效能的膨胀型阻燃剂.     

Sample evaporation in conventional GC split/splitless injectors. Part 1: Some quantitative estimates concerning heat consumption during evaporation

During sample evaporation in conventional vaporizing injection, the supply of heat to the evaporating liquid is a problem, first because the amounts of heat consumed are relatively large and, secondly, because the heat must be transferred to the sample within a very short time. Times available for evaporation, required amounts of heat, possible sources of heat, and the time required to transfer the heat to the sample liquid are discussed. It is shown that mixing with carrier gas contributes little heat to the evaporation process, but also that packings with glass wool have too low a heat capacity to deliver the required amount of heat to the evaporating sample. Transfer of heat from the insert wall to the sample easily requires several seconds, even if cooling of the vaporizing zone by 20° is accepted. Thus “flash evaporation” is usually impossible and most liquids must be held in the vaporizing chamber to allow full evaporation.     

NARROW-DISPERSED CROSSLINKED CORE-SHELL POLYMER MICROSPHERES PREPARED BY SURFACE-INITIATED ATOM TRANSFER RADICAL POLYMERIZATION＊

Grafting of polystyrene with narrowly dispersed polymer microspheres through surface-initiated atom transfer radical polymerization (ATRP) was investigated. Polydivinylbenzene (PDVB) microspheres were prepared by dispersion polymerization with poly(N-vinyl pyrrolidone) (PVP) as stabilizer. The surfaces of PDVB microspheres were chloromethylated by chloromethyl methyl ether in the presence of zinc chloride as catalyst to form chloromethylbenzene initiating core sites for subsequent ATRP grafting of styrene using CuCl/bpy as catalytic system. Polystyrene was found to be grafted not only from the particle surfaces but also from within a thin shell layer, resulting in the formation of particles size increased from 2.38-2.58μm, which can further grow to 2.93μm during secondary grafting polymerization of styrene. This demonstrates that grafting polymerization proceeds through a typical ATRP procedure with living nature. All of the prepared microspheres have narrow particle size distribution with coefficient of variation around 10%.     

Effects of Halogen Substitution on Naphthazarin Tautomerism in the Ground and Excited States

5,8-Hihydroxyl-1,4-naphthazarin was taken as a model compound to explore the effect of halogen substitution on intramolecular proton transfer process. Calculations indicate that the substitution in the R2- and R4-positions far away from the active region has much weaker influence on the IPT process than that in the R1-and R3-positions. IPT barriers for substitution in the R1-position are higher than that of parent molecule. However, it is quite reverse for substitution in the R3-position. The IPT process is a proton transfer process coupled with charge separation and coulombic interaction would be dominant during this process. As for naphthazarin, halogen substitution would decrease the quantum yields of O2 but increase those of 1O2.     

Fire retardant synergism between melamine and triphenyl phosphate in poly(butylene terephthalate)

The fire retardant efficiency of melamine (MA) and triphenyl phosphate (TPP) in poly(butylene terephthalate) (PBT) was studied by the limiting oxygen index (LOI) and the UL94 test. On adding 10 wt. % MA and 20 wt. % TPP, LOI increased from 20.9 to 26.6 and the UL94 V-0 rating was achieved. SEM and DSC analyses show that the fire retardants are compatible with PBT and facilitate crystallization of PBT. The occurrence of an interaction between MA + TPP and PBT was elucidated by TGA, dynamic FTIR, and pyrolysis/GC/MS. MA + TPP changes the degradation path of PBT and modifies the compositions of the gas and condensed-phase products.