Development of an automated monitoring system for various gas-phase organic carbonyls in ambient air

An automated monitoring system for various C₁ to C₅ gas-phase organic carbonyls in ambient air is described. The system consists of a parallel plate diffusion scrubber (PPDS), which is coupled with a high-performance liquid chromatography–ultraviolet (HPLC–UV) system using an automated injection valve. Compared with an annular diffusion scrubber (DS) employed so far for gas-phase carbonyl monitoring, PPDS shows an improved collection efficiency for formaldehyde, acetaldehyde, propionaldehyde, and acetone with >97% at an airflow rate of 0.5?L/min. High gas–liquid concentration ratios of PPDS and an optimised HPLC–UV system allow limits of detection (LOD) in a range of 80–500?pptv. A low liquid hold-up volume of the PPDS results in a short response time of about 10?min. Additionally, the optimised analysis time for 13 carbonyl compounds containing calibration standard enables brief measurement intervals of 25?min. The developed PPDS–HPLC system shows its reliability from urban site monitoring in Seoul, South Korea.     

Amperometric sensing of norepinephrine at picomolar concentrations using screen printed,high surface area mesoporous carbon

Norepinephrine (NE) is detected amperometrically using the enzyme Phenylethanolamine N-methyl transferase and cofactor S-(5′-Adenosyl)-l-methionine chloride dihydrochloride with disposable screen printed mesoporous carbon electrodes. The role of internal surface area and pore size of the mesoporous carbon is systematically examined using soft-templated, mesoporous silica–carbon powders with highly microporous walls obtained from etching of the silica to produce powders with surface areas ranging from 671–2339 m² g⁻¹. As the surface area increases, the sensitivity of the biosensor at very low NE concentrations (0–500 pg mL⁻¹) in phosphate buffered saline (PBS) increases just as the current signal increases with respect to the NE concentration of 81–1581 μA mL ng⁻¹ cm⁻² for the mesoporous carbons. The best performing electrode provides similar sensitivity in whole rabbit blood in comparison to PBS despite no membrane layer to filter the non-desired reactants; the small (<5 nm) pore size and large internal surface area acts to minimize non-specific events that decrease sensitivity.     

Microchannel membrane separation applied to confined thin film desorption

The concept of a confined thin film to enhance the desorption process is based on a reduced mass diffusion resistance. A wide thin film is formed into a microchannel by using a porous membrane as one wall of the channel enabling vapor extraction along the flow. Heat added to the channel results in vapor generation and subsequent extraction through the membrane. This experimental study investigates the performance of vapor extraction as a function of confined thin film thickness, pressure difference across the membrane and inlet concentration to the microchannel. In addition, heat added to the system was varied and results are presented in terms of the wall superheat temperature relative to the inlet saturated conditions of the binary fluid. The test section was equipped with a transparent window to observe bubble formation and vapor extraction. Results show that the performance, measured by the vapor release rate, increases for reduced channel thickness, for increased pressure difference across the membrane, and for lower inlet concentration. Results show that lower wall superheat correspond to higher heat transfer coefficients. Trends of Nusselt number and Sherwood number versus both channel Reynolds number and the product of the Reynolds number and Schmidt number are presented. Bubble formation in the channel does not degrade overall performance provided a critical heat flux condition does not occur.     

Comportement macroscopique des matériaux poreux à microstructure en feuilletsMacroscopic behavior of porous materials with lamellar microstructure

The solid phase of the porous material considered in this Note is made up of lamellar particles. The influence of interaction forces between platelets on the macroscopic behavior is addressed. The results provide a micromechanical basis to the modelling of the behavior of clays of the smectite group, for which repulsive forces arise from the electrical interaction between the solid platelets and the interstitial fluid. To cite this article: L. Dormieux et al., C. R. Mecanique 334 (2006).     

Study of porous silicon optical waveguides impregnated with organic dyes

Planar waveguides were made using oxidised porous silicon layers. Then, they were impregnated with Congo Red or Disperse Red 1 dyes. Optical losses were investigated before and after impregnation. In our case, the losses of impregnated waveguides were always higher than those of non-impregnated ones. In order to achieve a better understanding of the origin of these losses, we not only studied the absorbance of solutions which would impregnate the porous layers but also the reflectance spectra of the obtained composite materials. According to the measurements, the increase in losses in the visible spectrum depends on the intrinsic absorption of the dye while in NIR, the increase would be due to an accumulation of dried dye on the surface of the waveguide which would give rise to the surface scattering losses.     

Efficient luminescence from porous silicon

Photoluminescence measurements are carried out on porous silicon layers. We show the enhancement and stabilization of the luminescence when depositing a silicon nitride layer on top of porous layers.We also demonstrate that direct- and remote-plasma nitridation are good ways to reduce the ageing effect of porous silicon layers due to a passivation of dangling bonds.     

Numerical study of heat transfer in an optically thick semi-transparent spherical porous medium

In this paper, heat transfer by simultaneous convection, conduction and radiation in a semi-transparent spherical porous medium is investigated. The ROSSELAND approximation is adopted to take account of radiation in the heat transfer rate. The routine used here to solve the set of differential equations is taken from the IMSL MATH/LIBRARY. Various results are obtained for the dimensionless temperature profiles in the solid and fluid phases, the radiative, conductive, convective and total heat fluxes. The effects of some radiative properties of the medium on the heat transfer rate are examined.     

Deduction of tortuosity and porosity from acoustic reflection and transmission measurements on thick samples of rigid-porous materials

An acoustic method for obtaining the tortuosity, and porosity of thick samples of rigid porous materials consisting of large (>1 mm) grains or fibres is proposed. The method uses pulses with central frequencies close to 12 kHz and an approximate bandwidth of between 3 and 20 kHz. In this frequency range, inertial rather than viscous or scattering effects dominate sound propagation in large pores. This allows application of the high frequency limit of the “equivalent fluid” model. Both reflected and transmitted signals are used in the measurements. Tortuosity is deduced from the high frequency limit of the phase speed (obtained from transmission data) and porosity is obtained from the high frequency limit of the reflection coefficient once the tortuosity is known. The method is shown to give good results in the cases where significant scattering does not occur until frequencies much higher than the upper limit of the pulse bandwidth. Apart from its applicability to samples with several centimetres thickness, the method needs only one set of measurements with the sample to deduce both tortuosity and porosity. In principle the method can be used also to estimate characteristic lengths. However, the errors are found to be larger and the results less consistent than for tortuosity.     

Investigation on the mechanical properties of sintered porous copper compacts

In line with recent attention on porous metals having low and medium porosities in the range of 20-50%, this paper studies the effect of porosity on the mechanical properties of sintered copper compacts. Experiments were designed to investigate the effect of porosity, applied stress and sliding velocity on the wear rate of copper compacts, leading to the finding that the effects of both porosity and applied stress of the wear test on the wear rate are approximately similar and higher than that of sliding velocity. The investigation concerning the effect of porosity on compressive strength indicated that the stress-strain curve of high-porosity compact exhibited identifiable ultimate strength points, though low-porosity compact showed distinct stages of elastic plastic behavior.