飞秒激光冲击AZ31B镁合金过程的数值模拟

采用有限元分析法对飞秒激光冲击AZ31B镁合金进行数值模拟,研究了激光冲击处理对镁合金变形过程的影响,分析了单脉冲激光冲击下材料内部的位移、动能、应力和应变的分布情况,得到了材料的瞬态速度和应变率变化过程.仿真结果表明,单脉冲飞秒激光冲击镁合金产生的塑性变形,可在材料表面形成微米级凹坑,中心点处最大位移为34μm,最大变形速度390m/s;在冲击初期,材料表面的应力和应变主要分布在冲击区域中心节点和边缘附近,并且得到镁合金的最大应力和最大应变率分别为955 MPa和1.8×106 s-1.研究结果能够为深入分析飞秒激光与镁合金作用时材料变形参量的变化规律提供数值理论依据.     

10MJ高温超导环形磁体电磁优化设计

随着超导技术的发展,大容量、高场强的高温超导磁体已成为未来超导磁体的主要发展方向。文中以10MJ高温超导环形磁体为研究对象,以磁体的总用线量为优化目标,采用二代YBCO带材进行了环形磁体的电磁优化设计,利用遗传算法和有限元建模获得了磁体的最小总用线量,分析了在满足磁体储能量的情况下,线圈的内直径和线圈个数对环形磁体临界电流、总用线量的影响。     

胡克定律探究实验装置的改进

利用自制胡克定律探究实验装置对新课标中"探究弹簧弹力与形变量之间的关系"实验进行了改进,改进后的实验装置能直接在坐标纸上绘出弹簧弹力与形变量之间的对应关系点,通过拟合可得到F-x曲线,求拟合直线的斜率可求出被测弹簧的劲度系数.改进后的实验装置得出的实验结果与新课标教材中描述的现象一致.     

碳化硅晶体产生中红外飞秒激光研究获进展

中红外激光(3~5μm)在环境监控、气体分子识别、相干断层成像、军事等领域有着重要应用,特别是近年来在高次谐波产生单个阿秒脉冲的研究中,由于周期量级中红外飞秒激光能获得更高截止能量的谐波阶次,有望获得更短的阿秒脉冲和更高的时间分辨率,因此倍受人们的青睐。但受限于激光增益介质,目前较难在室温下直接获得中红外波段的飞秒激光,为此广泛应用的方案是基于非线性晶     

水嘴国标对17种重金属析出量强制限定

<正>质检总局和国家标准委不久前发布了新修订的《陶瓷片密封水嘴》(GB 18145–2014)强制性国家标准,将水嘴的重金属析出、密封性能、流量、寿命作为强制性条款,其中重金属析出一款对17种重金属析出规定了严格的限量值。新标准将于2014年12月1日实施。据国家标准委有关人士介绍,随着经济发展和社会进步,我国城乡居民对健康安全的要求越来越高。为满足健康安全需求,国家标准委高度重视水嘴铅超标问题,委托全国建筑卫生陶瓷标准化技术委员会组织行业专家、检验机构、     

隔膜对双电层电容器和混合型电池-超级电容器的电化学性能的影响

隔膜是双电层电容器和混合型电池-超级电容器等电化学储能器件的重要组成元件.本文采用1 mol?L-1四乙基四氟硼酸铵的丙烯碳酸酯电解液制备了基于活性炭的扣式双电层电容器,并采用1 mol?L-1六氟磷酸锂锂离子电解液制备了(LiNi0.5Co0.2Mn0.3O2+活性炭)/石墨体系的混合型电池-超级电容器.研究了不同类型隔膜的物理化学性能,以及其对双电层电容器和混合型电池-超级电容器的电化学性能的影响.四种隔膜分别是无纺布聚丙烯毡、多孔聚丙烯薄膜、Al2O3涂层的聚丙烯薄膜和纤维素纸隔膜.进行了表面形貌、差示扫描量热、电解液吸液量和表观接触角测试表征.电化学测试表明,采用纤维素隔膜的双电层电容器具有最高的比电容和更优的倍率性能,电容器的自放电性能差别不大.而对于混合型电池-超级电容器,采用聚丙烯薄膜和无纺布聚丙烯毡隔膜器件的比容量比其它器件约高20%,且采用纤维素隔膜的器件自放电率最高.     

低温热分析标准物质的研制

研制了两种0~100℃热分析标准物质,分别为金属镓和水杨酸苯酯标准物质。研制的标准物质具有良好的均匀性和稳定性,采用与NIST,LGC相应标准物质比较的方法定值。NIST为SRM 2234镓,其定值采用288.6~314.35 K范围内的绝热热量计测得温度及热量值;LGC用绝热法为水杨酸苯酯的熔化温度和熔化热定值,两种方法都可以直接溯源至SI单位。对定值结果的不确定度进行了分析和评定。镓和水杨酸苯酯标准物质的熔化温度分别为(29.77±0.20)℃(k=2),(41.81±0.34)℃(k=2);熔化热分别为(80.52±0.48)J/g(k=2),(88.94±0.62)J/g(k=2)。研制的两种标准物质满足国家标准物质的技术要求,申报已获批准。     

二异丁腈肼溶液中氮的选择性测定

二异丁腈肼分子结构中含有连氮(-N-N-)和氰基氮(-CN),每一个分子中有4个N原子,其结构式见图1。油溶性偶氮引发剂偶氮二异丁腈是重要的化工原料,广泛用于高分子的研究和生产,可作为氯乙烯、乙酸乙烯和丙烯腈等单体聚合引发剂,也可用作聚氯乙烯、聚烯烃、聚氨酯、聚乙烯醇、丙烯腈与丁二烯、苯乙烯共聚物等的发泡剂。此外,也可用于其它有机合成。偶氮二异丁腈由氯气氧化二异丁腈肼而制得,这开发了偶氮二异丁腈生产的新工艺,达到清     

Rapid,simple and selective determination of 2,4-dinitrophenol by molecularly imprinted spin column extraction coupled with fluorescence detection

A rapid, simple and selective method based on molecularly imprinted, spin column extraction coupled with fluorescence detection was successfully established for the determination of 2,4-dinitrophenol in serum samples. The 2,4-dinitrophenol imprinted polymers exhibited highly selective recognition for the template molecule and the maximum adsorption capacity was 138.9 mg/g. The results indicated that when water is used as the loading solution, only 2,4-dinitrophenol could be adsorbed on the spin column without the remaining structural analogs（2-nitrophenol, 4-nitrophenol and phenol）. After eluting with acetonitrile/acetic acid（9/1, v/v）, 2,4-dinitrophenol in serum samples could be determined by using the fluorescence spectrometer, based on the fluorescence enhancement of fluorescein by the template molecule. Under the optimal conditions, the spiked recovery ranged from 95.8% to 103.4% and the detection limit was 1 nmol/L. The results confirmed the reliability and practicality of the protocol and revealed a good perspective of this method for biological sample analysis.     

Alkali metal cation doping of metal-organic framework for enhancing carbon dioxide adsorption capacity

Metal-organic frameworks （MOFs） have attracted much attention as adsorbents for the separation of CO2 from flue gas or natural gas. Here, a typical metal-organic framework HKUST-I（also named Cu-BTC or MOF-199） was chemically reduced by doping it with alkali metals （Li, Na and K） and they were further used to investigate their CO2 adsorption capacities. The structural information, surface chemistry and thermal behavior of the prepared adsorbent samples were characterized by X-ray powder diffraction （XRD）, thermo-gravimetric analysis （TGA） and nitrogen adsorption-desorption isotherm analysis. The results showed that the CO2 storage capacity of HKUST-1 doped with moderate quantities of Li＋, Na＋ and K＋, individually, was greater than that of unmodified HKUST-1. The highest CO2 adsorption uptake of 8.64 mmol/g was obtained with 1K-HKUST-1, and it was ca. 11% increase in adsorption capacity at 298 K and 18 bar as compared with HKUST- 1. Moreover, adsorption tests showed that HKUST-1 and 1K-HKUST-1 displayed much higher adsorption capacities of CO2 than those of N2. Finally, the adsorption/desorption cycle experiment revealed that the adsorption performance of 1K-HKUST-1 was fairly stable, without obvious deterioration in the adsorption capacity of CO2 after 10 cycles.