Dislocation density crystalline plasticity modeling of lath martensitic microstructures in steel alloys

A three-dimensional multiple-slip dislocation density-based crystalline formulation, specialized finite-element formulations and Voronoi tessellations adapted to martensitic orientations were used to investigate large strain inelastic deformation modes and dislocation density evolution in martensitic microstructures. The formulation is based on accounting for variant morphologies and orientations, retained austenite and initial dislocation densities that are uniquely inherent to martensitic microstructures. The effects of parent austenite orientation and retained austenite were also investigated for heterogeneous fcc/bcc crystalline structures. Furthermore, the formulation was used to investigate microstructures mapped directly from SEM/EBSD images of martensitic steel alloys. The analysis indicates that variant morphology and orientations have a direct effect on dislocation density accumulation and inelastic localization in martensitic microstructures, and that lath directions, orientations and arrangements are critical characteristics of high strength martensitic deformation and behavior.     

On the cryogenic magnetic transition and martensitic transformation of the austenite phase of 7MoPLUS duplex stainless steel

The magnetic behaviour and martensitic transformation at cryogenic temperatures (down to 4 K) of the austenite phase of the duplex stainless steel (DSS), 7MoPLUS, were studied. As regards the prediction of Neel temperature, the empirical expressions for austenitic stainless steels are not applicable to the austenite phase of 7MoPLUS, although the composition of the austenite phase falls within the composition ranges within which the expressions were developed. Regarding the prediction of martensitic point Ms, the applicability of ‘old’ and recently developed expressions has been examined. The recently developed expressions, which take into account more alloying elements and their interactions, are not suitable for the austenite phase of 7MoPLUS. But for the ‘old’, simpler expressions, they seem to be valid in the sense that they all predict high stability of the austenite phase. Results obtained from 7MoPLUS were qualitatively the same as those obtained from another DSS, designated as 2205. Reasons for the applicability and inapplicability of these empirical expressions are suggested.     

Influence of modification time and high frequency ultrasound irradiation on self-assembling of alkylphosphonic acids on stainless steel: Electrochemical and spectroscopic studies

Self-assembly of alkylphosphonic acids on stainless steel was investigated under different conditions. Four different alkylphosphonic acids exhibiting alkyl chain of various size were synthesized and studied: butylphosphonic acid (C4P), octylphosphonic acid (C8P), decylphosphonic acid (C10P), and hexadecylphosphonic acid (C16P). Electrochemistry experiments were extensively carried out in order to determine electrochemical surface blocking of adsorbed layers in function of grafting time. In term of surface blocking, an 8 h modification time was optimal for all alkylphosphonic acids. Longer immersion times lead to degradation of adsorbed layers. For the first time, grafting of C16P was studied under high frequency ultrasound irradiation. Interestingly, grafting process is highly accelerated under sonication and well-covering C16P modified substrates are obtained after 1 h of immersion under ultrasound irradiation. This would allow to elaborate high-quality alkylphosphonic acids modified samples within much shorter times. Water contact angles measurements and X-ray Photoelectrons Spectroscopy (XPS) confirmed presence of adsorbed alkylphosphonic acids on stainless steel surface. A very tight link between electrochemical blocking, surface hydrophobicity and species chemical grafting was established.     

A ghost fluid Lattice Boltzmann method for complex geometries

A ghost fluid Lattice Boltzmann method (GF‐LBM) is developed in this study to represent complex boundaries in Lattice Boltzmann simulations of fluid flows. Velocity and density values at the ghost points are extrapolated from the fluid interior and domain boundary via obtaining image points along the boundary normal inside the fluid domain. A general bilinear interpolation algorithm is used to obtain values at image points which are then extrapolated to ghost nodes thus satisfying hydrodynamic boundary conditions. The method ensures no‐penetration and no‐slip conditions at the boundaries. Equilibrium distribution functions at the ghost points are computed using the extrapolated values of the hydrodynamic variables, while non‐equilibrium distribution functions are extrapolated from the interior nodes. The method developed is general, and is capable of prescribing Dirichlet as well as Neumann boundary conditions for pressure and velocity. Consistency and second‐order accuracy of the method are established by running three test problems including cylindrical Couette flow, flow between eccentric rotating cylinders and flow over a cylinder in a confined channel. Copyright © 2011 John Wiley & Sons, Ltd.     

Comparison of adjustable permanent magnetic field sources

A permanent magnet assembly in which the flux density can be altered by a mechanical operation is often significantly smaller than comparable electromagnets and also requires no electrical power to operate. In this paper five permanent magnet designs in which the magnetic flux density can be altered are analyzed using numerical simulations, and compared based on the generated magnetic flux density in a sample volume and the amount of magnet material used. The designs are the concentric Halbach cylinder, the two half Halbach cylinders, the two linear Halbach arrays and the four and six rod mangle. The concentric Halbach cylinder design is found to be the best performing design, i.e. the design that provides the most magnetic flux density using the least amount of magnet material. A concentric Halbach cylinder has been constructed and the magnetic flux density, the homogeneity and the direction of the magnetic field are measured and compared with numerical simulation and a good agrement is found.     

模具钢表面激光毛化工艺的试验研究

以模具工业45^#钢摩擦学设计及性能要求为基础，分析了激光毛化模具钢表面形貌的形成机理及其关键的影响因素。采用灯泵浦Nd：YAG脉冲激光器在试样表面进行激光毛化工艺试验，获得了合理的激光毛化参数范围：激光峰值功率0．8～1．6kW，离焦量-1．4～-0．4mm、＋0．4～4-1．4mm，辅助气体压力〉0．2MPa，脉宽1．8ms。采用功率增益和氧气保护，可加工出预先设定的微火山口状毛化形貌。微凹坑形貌的成功获得对于提高拉伸模具的摩擦磨损性能，进一步掌握激光毛化参数与材料的作用规律，提供了有效的数据参考。     

Optical system and lens design for Blu-ray disc optical pick-up

During the design process of Blu-ray disc optical pick-up (BD OPU), the optical system and the collimator lens design is especially important. This paper designs an optical system and some lenses for the BD OPU, including collimator lens, beam shaping lens for laser beam shaping, and cylinder lens for signal detecting. In this OPU, we use a triplet lens to collimate the laser beam. At the same time, we build a series of assembly jigs to make sure that each lens can be put into the OPU basement properly. At last, we get the reading spot image and S-curve photo of OPU, which can be used to read Blu-ray disc (BD).     

Corrosion Products Formed on Mild Steel Samples Submerged in Various Aqueous Solutions

Corroded samples, from the steel shell of an industrial evaporator system were investigated. A protective magnetite layer had formed, which subsequently dissolved in localised areas, resulting in failure of the shell. To clarify the mechanisms involved, mild steel samples of similar composition to the steel shell were submerged in the condensate and experiments were performed at room temperature and at 90°C under both static and dynamic conditions for exposure times up to 30 days. Control samples were submerged in deionised water under similar conditions. The dynamic corrosion rates in the industrial condensate were a factor of 2 higher than the rates for the deionised water, whilst static corrosion rates, measured in both media, were lower by a factor of 3 to 4 found for the dynamic experiments. The corrosion products were identified by means of CEMS analyses. The main components were magnetite and oxyhydroxides of iron. Additional to the species mentioned, -Fe₂O₃, goethite and hematite formed.     

Homotopy Structures for Algebras over a Monad

Let T be a monad over a category A. Then a homotopy structure for A, defined by a cocylinder P : A A, or path-endofunctor, can be lifted to the category A ^T of Eilenberg–Moore algebras over T, provided that P is consistent with T in a natural sense, i.e. equipped with a natural transformation : T P P T satisfying some obvious axioms. In this way, homotopy can be lifted from well-known, basic situations to various categories of algebras for instance, from topological spaces to topological semigroups, or spaces over a fixed space (fibrewise homotopy), or actions of a fixed topological group (equivariant homotopy); from categories to strict monoidal categories; from chain complexes to associative chain algebras. The interest is given by the possibility of lifting the homotopy operations (as faces, degeneracy, connections, reversion, interchange, vertical composition, etc.) and their axioms from A to A ^T , just by verifying the consistency between these operations and : T P P T. When this holds, the structure we obtain on our category of algebras is sufficiently powerful to ensure the main general properties of homotopy.     

Slow magnetohydrodynamic flow past a circular cylinder

Oseen’ approximations are used to study the slow motion of a viscous, incompressible, electrically conducting fluid past a circular cylinder in the presence of a uniform aligned magnetic field. Using series truncation method, the analytical solutions for the first three terms in the Fourier sine series expansion of the stream function are obtained. Numerical values of the tangential drag for different values of magnetic interaction parameter and viscous Reynolds number are calculated.