Periodic solutions and flip bifurcation in a linear impulsive system

In this paper, the dynamical behaviour of a linear impulsive system is discussed both theoretically and numerically. The existence and the stability of period-one solution are discussed by using a discrete map. The conditions of existence for flip bifurcation are derived by using the centre manifold theorem and bifurcation theorem. The bifurcation analysis shows that chaotic solutions appear via a cascade of period-doubling in some interval of parameters. Moreover, the periodic solutions, the bifurcation diagram, and the chaotic attractor, which show their consistence with the theoretical analyses, are given in an example.     

Preparation and characterization of Pt-supported porous graphite nanofibers

In this work, porous graphite nanofibers (PGNFs) were manufactured as promising catalyst supporter by a physical activation method for direct methanol fuel cells, and Pt nanoparticles were loaded on the PGNFs in order to prepare electrode materials by a chemical reduction method. The pore structures of the Pt/PGNFs were analyzed by N₂ adsorption isotherms at 77 K. Electrocatalytic activities of final products were investigated by voltammetry and conductivity measurements in a 1.0 M CH₃OH/0.5 M H₂SO₄. As a result, electrocatalytic activities of Pt/PGNFs were increased in the presence of Pt particles on the PGNFs and with increasing the specific surface area of the carbons.     

Dynamic adhesive strength of fiber-polymer systems

A new device for studying the dynamic adhesive strength is created. A procedure for determining the dynamic adhesive strength in fiber—polymer systems under impact loading (pull-out technique) is developed. The adhesive strength of the interface of polymer—steel wire joints formed by polymers of different chemical nature (epoxy resin, polysulfone, and polypropylene) is examined. It is shown that the dynamic adhesive strength grows as the loading rate increases for all the systems under investigation and that the relationship between the adhesive strength and the loading rate, , over a wide range of rates can be described by two straight lines corresponding to the quasi-static and impact loading, respectively. When passing from the quasi-static to dynamic loading, the character of scale relations of the adhesive strength does not change.Translated from Mekhanika Kompozitnykh Materialov, Vol. 35, No. 6, pp. 689–700, November–December, 1999.     

Stress State of Multilayer Structural Elements Subjected to Static Loading and Optimization of Laminated Beams and Bars

The results of FEM investigation of the triaxial stress state in multilayer structural elements subjected to axial and bending loads are presented. The distribution regularities of the stiffness and stresses or strains depending on the geometric and mechanical characteristics of layers and their position in the cross section of beams and bars are examined. The optimization of these elements is carried out using the dependences of the Bareisis—Paulauskas method and the Optim-98 computer program created by the present authors. As the optimization criteria, the strength, stiffness, mass, and cost of the structural elements are considered.     

Banach空间一阶脉冲微分方程的初值问题

利用单调迭代方法,在Ｂａｎａｃｈ空间研究了更为一般脉冲微分方程的初值问题的最小最大拟解的存在性及迭代逼近程序。     

Changes in ADC caused by tensile loading of rabbit achilles tendon: evidence for water transport

Water diffusion measurements were performed on rabbit Achilles tendons during static tensile loading and tendons in an unloaded state. The apparent diffusion coefficient (ADC) was measured along two directions: parallel and perpendicular to the long axis of the tendon. Tendons were studied after being prepared in two ways: (a) after being stored frozen in phosphate-buffered saline (PBS) and (b) freshly isolated. Statistically significant directional anisotropy was observed in the ADC in all tendons. The ADC was significantly greater in the direction parallel to the long axis of the tendon than in the perpendicular direction. The anisotropy is attributed to the greater restrictions seen by the water molecules in the perpendicular direction and is consistent with the known geometry of the tendon. Storage in PBS caused tendons to swell. This increased the ADC measured along both directions and reduced the anisotropy. The existence of anisotropy in the ADC was not related to the orientation of the specimen in the magnet. The ADC increased along both directions following the application of a 5-N tensile load; the increase was greatest along the perpendicular axis of the tendon. In order to determine whether load-related changes in the ADC reflected changes in interfibrilar spacing, we used electron microscopy to measure load-related changes in fibril spacing. Load-related changes in fiber spacing could not account for the observed changes in the ADC. The increase in ADC caused by loading was attributed to the extrusion of tendon water into a bulk phase along the outside surface of the tendon. In PBS-stored samples, enough fluid was extruded that it could be visualized. The transient response of the ADC to a 5-N tensile load was also studied. The absolute ADC in both directions increased with loading and recovered to baseline upon unloading. The transient changes in ADC, for both loading and unloading, had a mean time constant of approximately 15 min. The magnitude of the load-induced transient ADC changes was comparable to that seen in the static-loading experiments.     

一类参数不确定统一混沌系统的脉冲滞后同步

针对一类具有传输信道时间延迟且参数不确定的统一混沌系统，提出了一种脉冲控制同步方法.该方法将两个非自治混沌系统之间脉冲同步的实用稳定性问题转化为同步误差系统在原点的实用稳定性问题，基于脉冲微分方程的相关理论，给出了同步误差系统在原点的实用稳定判据，仿真结果验证了方法的有效性. 关键词： 统一混沌系统 混沌同步 脉冲控制 实用稳定性     

HCSB-DEMO�������������ȷ�����������

根据HCSB-DEMO堆的设计要求,对不同尺寸的聚变堆能产生的聚变功率、中子壁负载和等离子体燃烧时间等进行计算与分析,给出了符合设计要求的堆芯参数。在所选定的堆芯参数条件下进行了零维功率平衡计算分析,给出了3组HCSB-DEMO堆的等离子体初步设计参数。     

Simulation of non-selfadjoint control of thin elastic plates in the presence of conservative in-plane forces

Summary Based on the analysis presented in [1], a closed-form solution for the response of a controlled plate to a transversely applied dynamic loading is presented. Both the applied loading and the control are considered to be continuously distributed. The results and the corresponding parametric study are presented for two common boundary conditions of SSSS and SFSF in the plates. Received 11 March 1997; accepted for publication 18 March 1998