Fracture characteristics of concrete subjected to impact loading

This paper takes concrete as a four-phase composite made of the intact matrix and three mutually perpendicular groups of penny-shaped micro-cracks. The intact matrix is assumed to be elastic,homogeneous and isotropic,and the micro-cracks are penny-shaped. Combined with the failure mechanism of concrete subjected to impact loading,a dynamic constitutive model for concrete is developed based on Mori-Tanaka's average stress concept and Eshelby's equivalent inclusion theory. Experimental results show that concr...     

A novel self-locked energy absorbing system

Metallic thin-walled round tubes are widely used as energy absorption elements. However, lateral splash of the round tubes under impact loadings reduces the energy absorption efficiency and may cause secondary damage. Therefore, it is necessary to assemble and fasten round tubes together by boundary constraints and/or fasteners between tubes, which increases the time and labor cost and affects the mechanical performance of round tubes. In an effort to break through this limitation, a novel self-locked energy-absorbing system has been proposed in this paper. The proposed system is made up of thin-walled tubes with dumbbell-shaped cross section, which are specially designed to interlock with each other and thus provide lateral constraint under impact loadings. Both finite element simulations and impact experiment demonstrated that without boundary constraints or fasteners between tubes, the proposed self-locked energy-absorbing system can still effectively attenuate impact loads while the round tube systems fail to carry load due to the lateral splashing of tubes. Furthermore, the geometric design for a single dumbbell-shaped tube and the stacking arrangement for the system are discussed, and a general guideline on the structural design of the proposed self-locked energy absorbing system is provided.     

Influence of pressure on the relative population of the two lowest vibrational levels of the C <Superscript>3</Superscript> Π<Subscript>u</Subscript> state of nitrogen for electron beam excitation

Continuous and pulsed 12 keV electron beams were used to excite nitrogen within a gas cell at pressures ranging from 10 to 1400 hPa. The pressure dependence of the ratio of photon fluxes for emission from vibrational levels v'=0 and 1 of the C ³Π _u state has been studied. The results confirm the presence of a collisional excitation mechanism populating v'=0, 1 in addition to electron impact excitation. Rate constants of (1.27 ±0.04)×10^-11 cm³s^-1 [ v'=0] and (2.68 ±0.08)×10^-11 cm³s^-1 [ v'=1] were measured for C ³Π _u quenching by ground state nitrogen. For electron beam conditions relative excitation efficiencies of 1:0.59:0.22 for vibrational levels 0, 1 and 2 were calculated. The recorded flux ratios are compared with the predictions given by a vibrational relaxation model.     

飞秒激光激发空气电离的阈值研究

报道在脉宽50fs—22ps，波长800nm脉冲激光作用下的空气电离阈值的研究结果.利用探测等离子体发光信号的方法，实验测量了激发空气电离所需的阈值激光强度.结果表明，当激光脉冲宽度从50fs增加到22ps时，阈值光强I_th从8.7×10¹⁴W/cm²下降到2.7×10¹³W/cm²；I_th经历了由迅速降低逐渐发展为缓慢降低的过程.在50fs—1p     

A novel pose and illumination robust face recognition with a single training image per person algorithm

In the real-world application of face recognition system, owing to the difficulties of collecting samples or storage space of systems, only one sample image per person is stored in the system, which is so-called one sample per person problem. Moreover, pose and illumination have impact on recognition performance. We propose a novel pose and illumination robust algorithm for face recognition with a single training image per person to solve the above limitations. Experimental results show that the proposed algorithm is an efficient and practical approach for face recognition.     

Preparation and characterization of Pt-supported porous graphite nanofibers

In this work, porous graphite nanofibers (PGNFs) were manufactured as promising catalyst supporter by a physical activation method for direct methanol fuel cells, and Pt nanoparticles were loaded on the PGNFs in order to prepare electrode materials by a chemical reduction method. The pore structures of the Pt/PGNFs were analyzed by N₂ adsorption isotherms at 77 K. Electrocatalytic activities of final products were investigated by voltammetry and conductivity measurements in a 1.0 M CH₃OH/0.5 M H₂SO₄. As a result, electrocatalytic activities of Pt/PGNFs were increased in the presence of Pt particles on the PGNFs and with increasing the specific surface area of the carbons.     

Dynamic adhesive strength of fiber-polymer systems

A new device for studying the dynamic adhesive strength is created. A procedure for determining the dynamic adhesive strength in fiber—polymer systems under impact loading (pull-out technique) is developed. The adhesive strength of the interface of polymer—steel wire joints formed by polymers of different chemical nature (epoxy resin, polysulfone, and polypropylene) is examined. It is shown that the dynamic adhesive strength grows as the loading rate increases for all the systems under investigation and that the relationship between the adhesive strength and the loading rate, , over a wide range of rates can be described by two straight lines corresponding to the quasi-static and impact loading, respectively. When passing from the quasi-static to dynamic loading, the character of scale relations of the adhesive strength does not change.Translated from Mekhanika Kompozitnykh Materialov, Vol. 35, No. 6, pp. 689–700, November–December, 1999.     

Dissociative attachment of low-energy electrons to vibrationally excited molecules using a photoelectron source

The process of dissociative attachment (DA) of low-energy electrons ) to vibrationally excited sodium dimer molecules is studied with high electron energy resolution () in a supersonic molecular beam. A novel photoelectron source, based on two-step photoionization of the sodium atoms in the beam, may deliver a current of up to 1 nA and has been used with a current of typically 0.2 nA in this experiment. The energy dependence of the rate of sodium anion formation is determined by ion detection based on a time-of-flight analysis. The molecules are selectively excited to levels using the technique of coherent population transfer by delayed pulses (STIRAP). The comparison of the experimental data with recent resonance model calculations based on improved potential curves reveals generally good agreement for levels v ”>12. For some distinct differences between theoretical and experimental results persist. Received: 21 November 1998 / Received in final form: 7 April 1999     

Total cross-sections for positron scattering by a series of molecules

The additivity rule is employed to obtain the total (elastic+inelastic) cross-sections for positron scattering from molecules including a number of diatomic, polyatomic molecules (H₂, N₂, HCl, CO₂, NH₃, SF₆, CH₄, C₂H₄ and C₃H₈) over an incident energy range of 10-1000 eV. The total cross-sections (TCS) of the constituent atoms of molecules are obtained by employing a complex optical model potential (composed of static, polarization and absorption potential). The present results are compared with experimental data and other theoretical calculations, good agreement is obtained in intermediate- and high-energy region. Received: 11 November 1997 / Revised: 23 March 1998 / Accepted: 16 June 1998     

Viscoelastic characterization of compacted pharmaceutical excipient materials by analysis of frequency-dependent mechanical relaxation processes

A newly developed method for determining the frequency-dependent complex Young's modulus was employed to analyze the mechanical response of compacted microcrystalline cellulose, sorbitol, ethyl cellulose and starch for frequencies up to 20 kHz. A Debye-like relaxation was observed in all the studied pharmaceutical excipient materials and a comparison with corresponding dielectric spectroscopy data was made. The location in frequency of the relaxation peak was shown to correlate to the measured tensile strength of the tablets, and the relaxation was interpreted as the vibrational response of the interparticle hydrogen and van der Waals bindings in the tablets. Further, the measured relaxation strength, holding information about the energy loss involved in the relaxation processes, showed that the weakest material in terms of tensile strength, starch, is the material among the four tested ones that is able to absorb the most energy within its structure when exposed to external perturbations inducing vibrations in the studied frequency range. The results indicate that mechanical relaxation analysis performed over relatively broad frequency ranges should be useful for predicting material properties of importance for the functionality of a material in applications such as, e.g., drug delivery, drug storage and handling, and also for clarifying the origin of hitherto unexplained molecular processes.