基于任意形状颗粒集合二值图像的体积估算模型

基于任意形状颗粒集合的二值图像,提出了估计其体积(或质量)的方法.首先利用发光背景台面获取的颗粒灰度图像变换为相应的二值图像,得到颗粒的边界轮廓.然后再基于其边界信息,定义与颗粒形状特征相关的描述量,并将其无量纲化.将由此定义的无量纲参变量作为回归变量建立一个多元线性回归(multiple linear regression)模型用以估计颗粒集合的扁平度,进而估算颗粒体积.回归变量的系数由随机采样的501个样本颗粒(尺寸范围为4.75～25 mm)用误差最小平方和求得.将模型应用于由具有相似统计分布特征的其他颗粒集合,并将得到的体积估计值与其体积真实值相比较,实验结果显示模型的相对误差在±2%以内.     

BNL/AGS10.7A GeV金核诱发作用中核碎裂与粒子产生

研究了在美国BNL/AGS上能量10.7AGeV的¹⁹⁷Au离子诱发核作用,报告了EMU–01国际合作实验关于射弹核碎裂和产生粒子密度等最新实验结果.     

用方差定义的激光束横向尺寸的测量

用方差定义的激光束横向尺寸,有着普适、简单和便于利用光学元件并行运算功能的特点.本文提出一种借助改变柱形容器内吸收液浓度来直接测量各种波长激光束横向尺寸的理论和方法.     

Size dependence of self-diffusion in the hard-square lattice gas

A striking size dependence of the mean-square displacement of diffusing particles in the two-dimensional lattice gas of hard squares has been observed by Monte Carlo simulation. It is shown that the size effect is due to the formation of a stable cage structure in small lattices when the particle concentration is high. The formation of cages is governed by a new type of percolation problem related to bootstrap percolation.     

Spectroscopy on very neutron-rich nuclei beyond N = 20

Recent studies on nuclear structure by using radioactive isotope beams available at the RIKEN projectile-fragment separator (RIPS) are introduced. Special emphasis is given to two selected experiments from recent programs that highlight studies on the magicity loss observed for very neutron-rich nuclei beyond N = 20 in the “island-of-inversion” region; the particle stability of ³¹F, and the low-lying excited states of ³⁴Mg. Received: 1 May 2001 / Accepted: 4 December 2001     

Full-Wave Analyses for a Multi-Layered Microstrip Patch Antenna

This paper describes numerical modelling of a dual band multi-layered microstrip patch antenna operating at 35GHz on an in-house semi-insulating GaAs substrate. The simulated and measured resonant frequencies at both lower and upper resonant frequencies will be compared to check the accuracy of the different numerical modelling techniques.     

胶体颗粒大小的分布——Ⅱ.物理显影中胶体催化剂颗粒大小的分布函数

本文用对数正态分布对物理显影中常用的Au、Ag及Ag_2s胶体催化剂的颗粒大小的实验分布进行了拟合。理论分布与实验分布的比较表明:本实验条件下制备的十二组胶体溶液其颗粒大小都服从了对数正态分布,并且不依赖于胶体的组成、大小及制备方法。因此,它们很可能遵从了同样的成核成长规律。     

Mesoporous nanotube aggregates obtained from hydrothermally treating TiO2 with NaOH

Nanotube aggregates with high porosity were prepared from hydrothermal treatment of TiO₂ particles in NaOH at 130 °C, followed by HCl rinsing to different pH values. Pore structure of the aggregates, which were mainly mesoporous, was characterized by analyzing the N₂ sorption isotherm with different methods including the t-plot and density function theory. The surface area, pore volume and mean pore size of the aggregates increased with the rinsing acidity to reach a maximum (e.g. 400 m²/g in surface area) at pH 1.6 and then decreased with further increase of the acidity. The crystalline phase and composition of the aggregates were, as well, significantly affected by the acidity of the post-treatment rinsing. Large-surface area aggregates were of loosely-attached nanotubes, composed of both anatase TiO₂ and H₂Ti₂O₅·H₂O, obtained under a mildly acidic rinsing condition, while basic or highly acidic conditions resulted in the formation of closely coagulated dense structures consisting of different crystalline phases.     

Facile syntheses of surface-functionalized micelles and shell cross-linked nanoparticles

Block copolymer micelles and shell cross-linked nanoparticles (SCKs) presenting Click-reactive functional groups on their surfaces were prepared using two separate synthetic strategies, each employing functionalized initiators for the controlled radical polymerization of acrylate and styrenic monomers to afford amphiphilic block copolymers bearing an alkynyl or azido group at the α-terminus. The first route for the synthesis of the azide-functionalized nanostructures was achieved via sequential nitroxide-mediated radical polymerization (NMP) of tert-butyl acrylate and styrene, originating from a benzylic chloride-functionalized initiator, followed by deprotection of the acrylic acids, supramolecular assembly of the block copolymer in water and conversion of the benzylic chloride to a benzylic azide. In contrast, the second strategy utilized an alkynyl-functionalized reversible addition fragmentation transfer (RAFT) agent directly for the RAFT-based sequential polymerization of tetrahydropyran acrylate and styrene, followed by selective cleavage of the tetrahydropyran esters to give the α-alkynyl-functionalized block copolymers. These Click-functionalized polymers, with the functionality located at the hydrophilic polymer termini, were then self-assembled using a mixed-micelle methodology to afford surface-functionalized “Clickable” micelles in aqueous solutions. The optimum degree of incorporation of the Click-functionalized polymers was investigated and determined to be ca. 25%, which allowed for the synthesis of well-defined surface-functionalized nanoparticles after cross-linking selectively throughout the shell layer using established amidation chemistry. Functionalization of the chain ends was shown to be an efficient process under standard Click conditions and the resulting functional groups revealed a more “solution-like” environment when compared to the functional group randomly inserted into the hydrophilic shell layer. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5203–5217, 2006