Adsorptive Bubble Separation of Dinitrophenol

Dinitrophenol was removed from aqueous solution by various adsorptive bubble separation techniques. Foam fractionation of dinitrophenol with hexadecyltrimethylammonium bromide(HTA) was most effective with over 99% removal in 15 min. The addition of a surfactant in greater than stoichiometric amounts was required for effective separation. Solvent sublation of the dinitrophenol-HTA complex was also effective. The separation efficiency of solvent sublation of dinitrophenol-HTA was similar to that of foam fractionation. The separation by solvent sublation of dinitrophenol without adding any surfactant was very poor. Adsorbing colloid flotation with Fe(OH)₃ was not effective in removing dinitrophenol from aqueous solution.     

Determination of Halogenated Hydrocarbons in Insulating Polymeric Foams

A simultaneous thermal analysis/mass spectroscopy system was used for the determination of halogenated hydrocarbons in polymeric foam insulation materials. The investigation of ten different polymeric foams show that this equipment is a sensitive and reliable tool for the identification and determination of the bubbling agent. The results are compared with the Purge and Trap method. This revised version was published online in July 2006 with corrections to the Cover Date.     

Determination of Hg from Cu concentrates by X-ray fluorescence through preconcentration on polyurethane foam

A methodology was developed for the separation and determination of microamounts of mercury from copper concentrate samples by wavelength dispersive X-ray fluorescence (WDXRF) after solid-phase extraction of mercury from iodide medium using polyurethane foam (PUF). The best sorption conditions for the Hg-KI-PUF system were settled using X-ray fluorescence technique after collection of ground PUF on a filter paper by vacuum filtration and direct measurement of the intensity signal of the sorbed mercury on PUF. The main parameters of sorption such as iodide concentration, pH, shaking time and sample dilution effect were studied. The system shows rapid kinetic sorption and maximum X-ray intensity signal was achieved after shaking for 2 min a 0.01 mol l⁻¹ iodide solution containing microamounts of mercury in the pH range from 1.0 to 9.0. Effective sorption up to a volume of 0.9 l allows preconcentration of mercury. A linear fit up to 50 μg mercury was obtained by the plot of the initial mercury mass in the bulk solution (0.5 l) vs. its respective XRF intensity signal measurement on ground PUF after the sorption process. The calibration sensitivity, quantification and detection limits found were 9.09 CPS μg⁻¹, 9.0 and 2.7 μg, respectively. The sorption of many elements was also evaluated under the best conditions. High concentrations of Cu(II) and Fe(III) interfere seriously. Mercury-selective separation could be achieved using citrate or EDTA as masking agent; no interference due to copper matrix samples was observed in citrate medium. This methodology was evaluated by recovery for mercury determination in copper concentrate ore samples supplied by a mining industry and copper sulfate salts; the results were between 98% and 106%.     

Investigation of the Removal of Lead by Adsorption onto 1‐(2‐Thiazolylazo)‐2‐Naphthol (TAN) Imbedded Polyurethane Foam from Aqueous Solution

A new preconcentration method is presented for lead on TAN‐loaded polyurethane foam (PUF) and its measurement by differential pulse anodic stripping voltammetry (DPASV). The optimum sorption conditions of 1.29 × 10^?5 M solution of Pb(II) ions on TAN‐loaded PUF were investigated. The maximum sorption was observed at pH 7 with 20 minutes equilibrated time on 7.25 mg mL^?1 of TAN‐loaded foam. The kinetic study indicates that the overall sorption process was controlled by the intra‐particle diffusion process. The validity of Freundlich, Langmuir and Dubinin ‐ Radushkevich adsorption isotherms were tested. The Freundlich constants 1/n and K_F are evaluated to be 0.45 ±0.04 and (1.03 +0.61) × 10^?3 mol g^?1, respectively. The monolayer sorption capacity and adsorption constant related to the Langmuir isotherm are (1.38 ± 0.08) × 10^?5 mol g^?1 and (1.46 ± 0.27) × 10⁵ L mol^?1, respectively. The mean free energy of Pb(II) ions sorption on‐TAN loaded PUF is 11.04 ± 0.28 kJ mol^?1 indicating chemisorption phenomena. The effect of temperature on the sorption yields thermodynamics parameters of ΔH, ΔS and ΔG at 298 K that are 15.0 ± 1.4 kJ mol^?1, 74 ±5 J mol^?1 K^?1 and ‐7.37 ± 0.28 kJ mol^?1, respectively. The positive values of enthalpy (ΔH) and entropy (ΔS) indicate the endothermic sorption and stability of the sorbed complexes are entropy driven. However, the negative value of Gibb's free energy (ΔG) indicates the spontaneous nature of sorption. On the basis of these data, the sorption mechanism has been postulated. The effect of different foreign ions on the sorption and desorption studies were also carried out. The method was successfully applied for the determination of lead from different water samples at ng levels.     

泡沫塑料线膨胀系数的处理方法

对于一些诸如泡沫塑料等的非均匀材料，其长度随温度变化的规律并非直线性，在以往的试验中，是先将温度曲线人为地分为若干段，并给出各段的材料平均线膨胀系数。为了更加精确地反映和处理这类物质的温度行为，本文提出了一种数学处理方法，以此来拟合材料的实际温度行为。根据此拟合式可给出材料在实际温度变化内的每一温度下的线膨胀系数。     

Poly(lactic acid)/organoclay nanocomposites: Thermal,rheological properties and foam processing

In this study, polymer nanocomposites based on poly(lactic acid) (PLA) and organically modified layered silicates (organoclay) were prepared by melt mixing in an internal mixer. The exfoliation of organoclay could be attributed to the interaction between the organoclay and PLA molecules and shearing force during mixing. The exfoliated organoclay layers acted as nucleating agents at low content and as the organoclay content increased they became physical hindrance to the chain mobility of PLA. The thermal dynamic mechanical moduli of nanocomposites were also improved by the exfoliation of organoclay; however, the improvement was reduced at high organoclay content. The dynamic rheological studies show that the nanocomposites have higher viscosity and more pronounced elastic properties than pure PLA. Both storage and loss moduli increased with silicate loading at all frequencies and showed nonterminal behavior at low frequencies. The nanocomposites and PLA were then foamed by using the mixture of CO₂ and N₂ as blowing agent in a batch foaming process. Compared with PLA foam, the nanocomposite foams exhibited reduced cell size and increased cell density at very low organoclay content. With the increase of organoclay content, the cell size was decreased and both cell density and foam density were increased. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 689–698, 2005     

Modeling of the role of defects in sintered FeCrAlY foams

The metal sintering approach offers a cost- effective means for the mass-production of open-cell foams from a range of materials, including high-temperature steel alloys, which offer novel mechanical and acoustic properties. In a separate experimental study, the mechanical properties of open-celled steel alloy (FeCrAlY) foams have been characterized under uniaxial compression and shear loading. Compared to predictions from established models, a significant knockdown in material properties was observed. This knockdown was attributed to the presence of defects throughout the microstructure that result from the unique fabrication process. In the present paper, the microstructure of sintered FeCrAlY foams was modeled by using a finite element (FE) model. In particular, microstructural variations were introduced to a base lattice, and the effects on the strength and stiffness calculated. A range of defects identified under scanning electronic microscope (SEM) imaging were considered including broken ligaments, thickness variations, and pore blockages, which are the three primary imperfections observed in sintered foams. The corresponding levels of defect present in the material were subsequently input into the FE model, with the resulting predictions correlating well with experimental data. The project supported by the National Basic Research Program of China (2006CB601202), the National Natural Science Foundation of China (10328203, 10572111, 10632060), the National 111 Project of China (B06024), and the US Office of Naval Research (N000140210117).     

Highly structured porous solids from liquid foam templates

We demonstrate the generation of highly structured porous solids from liquid foam templates, using ordered foam layers and threads made from hydrogels. For this purpose we separate sufficiently foam generation and solidification: well known and highly controllable liquid foam structures are created, which are thereafter ‘frozen’ in situ through polymerisation and cross-linking. Being extendible to a large range of materials and length scales, such an approach opens up a plethora of opportunities in material development.     

电沉积-钨丝电热原子吸收光谱法测定地质样品中痕量金

以市售幻灯投仪卤钨灯泡钨丝为原子化器的钨丝电热原子吸收光谱分析仪(TC-AAS),功率小、仪器成本低[1,2],如用微型CCD光谱仪作检测系统,可以实现原子吸收光谱仪的小型化,甚至可用于野外现场分析[3,4].     

Effect of a natural contaminant on foam fractionation of bromelain

Foam fractionation is a simple, inexpensive method for separating and purifying proteins. Typically, a dilute bromelain solution with a pH ranging from 2.0 to 7.0 foams very well when bubbles are introduced into a foam fractionation column. It was observed, however, that the dilute enzyme solution only foamed between approximately pH 2.0 and 3.0 when the inner wall of the fractionation column was coated with a natural contaminant (okra residue). We studied the separation ratio and the protein mass recovery to explore the effect of a natural antifoaming agent on the foam fractionation of a dilute bromelain solution. The control variables used in this process were the initial bulk solution pH, which ranged from 2.0 to 7.0, and the superficial air velocity, which varied between 1.7 and 6.2 cm/s.