烧结温度对Eu3+在羟基磷灰石中发光性能的影响

采用化学沉淀法制备了一系列Eu³⁺掺杂的羟基磷灰石样品,并在不同温度下对样品进行了烧结.使用X射线衍射、红外光谱以及荧光光谱等对样品的结构及发光特性进行了研究.分析表明,烧结对Eu掺杂羟基磷灰石的结构及结晶度产生了影响.在394 nm激发下,样品出现Eu的特征发射,掺杂摩尔分数一定时,随烧结温度增加,样品的荧光发光强度先增大后减小,在500 ℃达到峰值.其荧光寿命随烧结温度的升高而延长.此外,样品中电偶极跃迁与磁偶极跃迁强度之比(I_R:I_O)也随烧结温度的增加先增大后减小.分析表明,烧结温度的改变通过晶体结构对样品的荧光特性以及掺杂取代位置产生了影响.     

焙烧温度对Mn/Al2O3-TiO2催化剂结构及氧化NO性能的影响

采用溶胶凝胶法和浸渍法制备10% Mn/Al₂O₃-TiO₂催化剂,借助TPO、XRD、O₂-TPD、Raman、XPS等手段,考察焙烧温度(450~650 ℃)对催化剂结构以及氧化NO性能的影响。TPO结果表明催化剂活性随焙烧温度的升高先增后减,其中焙烧温度为550 ℃时催化剂活性最好。XPS结果显示随着焙烧温度的升高(450~550 ℃),催化剂表面Mn³⁺的含量逐渐升高,与催化剂活性的强弱成对应关系,并且催化剂晶格氧含量下降,而表面化学吸附氧从40.9%增加到64.8%。Raman分析显示550 ℃焙烧时,催化剂表面存在丰富的Mn₂O₃活性物种,并且O₂-TPD分析也表明随着焙烧温度的升高,晶格氧向表面化学吸附氧流动,提高了化学吸附态氧物种的含量。这些结果表明Mn₂O₃可能是NO氧化起主要作用的活性Mn物种,释放更多的表面化学吸附氧物种,将有助于促进NO的催化氧化。     

LaNiO3的焙烧温度对甲醇水蒸气重整制氢CuO/LaNiO3催化剂的影响

采用溶胶凝胶法合成了LaNiO_3钙钛矿型氧化物载体,再采用浸渍法制备了CuO/LaNiO_3催化剂,并通过XRF、XRD、BET、H_2-TPR和XPS等手段对催化剂进行了表征,考察了LaNiO_3钙钛矿的焙烧温度对CuO/LaNiO_3催化剂结构及其催化甲醇水蒸气重整制氢性能的影响。结果表明,载体焙烧温度主要影响了催化剂的表面晶格氧缺位,活性组分和载体间的相互作用。当载体焙烧温度为800℃时,催化剂表面氧空穴较多,活性组分与载体间相互作用较强,因此,催化甲醇水蒸气重整制氢活性较好。     

半水硫酸钙晶须的水化机理及稳定性调节

通过探讨半水硫酸钙晶须(HCSW)贮存过程在空气中形貌和晶形的变化,研究了半水硫酸钙晶须的水化机理,分析了不同处理方法对其稳定性的调节。研究发现,HCSW的水化是由晶须表面的-OH基团和Ca^2+活性位点以及HCSW存在的内部通道引起的,煅烧和二元醇改性均可提高硫酸钙晶须的耐水性。结果表明,煅烧后,半水硫酸钙晶须转化为无水可溶硫酸钙晶须和无水死烧硫酸钙晶须,易于水化的内部通道消失,耐水性增强;水热合成过程二元醇的加入,可利于醇羟基吸附在HCSW的(200)、(020)和(220)表面,阻止H2O分子中羟基在晶须表面的吸附,进而提高晶须的耐水性,当添加剂为三乙二醇(TEG)且浓度为18.8 mmol·L^-1时,HSCW在空气中耐水稳定性不小于7 d。     

Co/Hβ催化剂上N_2O的分解性能研究

采用浸渍法制备了Hβ分子筛负载钴氧化物催化剂。考察了催化剂焙烧温度和钴负载量对催化剂催化分解N2O活性的影响,并采用XRD、NH3-TPD、H2-TPR、SEM等手段对催化剂的理化性质进行表征。结果表明,催化剂中的钴物种主要以Co3O4尖晶石型形态存在;催化剂焙烧温度显著影响其酸性和酸量及氧化还原性能,焙烧温度达到700℃后,催化剂中有难还原的Co-Al-O物种生成。焙烧温度和钴负载量对催化剂的催化活性均有影响,焙烧温度为600℃、钴负载量为10%~15%的催化剂催化活性好,N2O分解温度低,t10、t50和t95分别为325~329℃、364~367℃和406~408℃。     

Optimization of electrospun TiO2 nanofibers photoanode film for dye‐sensitized solar cells through interfacial pre‐treatment,controllable calcination,and surface post‐treatment

Dye‐sensitized solar cells (DSSCs) are generally viewed as next generation photovoltaic devices. Electrospun TiO₂ nanofibers (NFs) film can be used to construct photoanode for DSSCs. A systematic strategy to optimize such a novel photoanode material of DSSCs was elaborated in this paper. A main drawback of NFs photoanode is the poor adhesion of ceramic NFs film to its conductive glass substrate. This problem can be well solved by sandwiching a transition layer between the overlaid NFs film and the underlaid glass substrate through an interfacial spin‐coating pre‐treatment. After electrospinning, a controllable calcination is also indispensable for obtaining an ideal nanofibrous mat with good morphology and adhesion. The choice of calcination parameters including temperature, holding time, and heating rate was discussed in detail. In addition, a surface TiCl₄ post‐treatment can further improve adhesion as well as strength for the NFs photoanode film. And the performance of the resulting DSSCs will benefit from the TiCl₄ post‐treatment. Copyright © 2013 John Wiley & Sons, Ltd.     

Zn-Fe尖晶石型复合氧化物催化分解N2O

用共沉淀法制备了Zn-Fe尖晶石型复合氧化物催化剂,用于有氧气氛中N₂O的分解反应;考察了复合氧化物的组成、焙烧温度及K改性对其催化活性的影响,并用氮气吸附、XRD和H₂-TPR等技术对催化剂结构进行了表征。结果表明,Zn-Fe尖晶石型复合氧化物具有良好的催化N₂O分解的活性;在优化出的Zn_0.8Fe_0.2Fe₂O₄-400催化剂上500℃下连续反应10 h时,有氧无水和有氧有水条件下N₂O转化率分别达到63.5%和22.2%。K改性Zn-Fe尖晶石型复合氧化物的催化活性均不及纯Zn-Fe氧化物,这是由于K改性催化剂的比表面积显著降低,而且K粒子迁移至催化剂表面,抑制了FeO_x的还原和表面氧物种的脱除。     

焙烧温度对微乳液法负载铂制备的Pt-S2O82-/ZrO2-Al2O3催化剂异构化性能的影响

过微乳液法负载Pt制备了Pt-S₂O₈^2-/ZrO₂-Al₂O₃(Pt-SZA-X) 催化剂,并采用XRD、BET、FT-IR、TPR、TEM等手段对催化剂进行了表征。以正戊烷异构化反应为探针,考察了焙烧温度对催化剂异构化性能的影响。结果表明,焙烧温度对Pt-SZA-X的还原温度影响不大,但催化剂表面S含量随着焙烧温度的升高而下降;焙烧温度为600~650℃时形成O=S=O结构,此时S与催化剂载体结合比较稳定;焙烧温度为650℃时,可得到单一的ZrO₂四方晶相,焙烧温度高于650℃时,比表面积迅速降低,催化剂表面S⁶⁺流失严重。在不同温度下焙烧得到的催化剂中,经650℃焙烧的催化剂具有适宜的超强酸位和比表面积,异构化活性最高。在反应温度为230℃、反应压力2.0 MPa、氢烃物质的量比4:1、质量空速1.0 h^-1时,催化异戊烷产率达到60.8%。     

Effect of calcination temperature on the performance of nano-size iron oxide catalysts for ethylbenzene dehydrogenation

The effect of calcination temperature on the physicochemical properties and catalytic performance of nano-sized Fe-K oxides for ethylbenzene dehydrogenation was investigated. The catalyst calcined at 600°C showed the highest activity. The catalytic activity of the catalysts clearly depended on the structure of the nano-sized iron catalysts.     

Large-scale synthesis of single-crystalline MgO with bone-like nanostructures

Uniform bone-like MgO nanocrystals have been prepared via a solvothermal process using commercial Mg powders as the starting material in the absence of any catalyst or surfactant followed by a subsequent calcination. Field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM) measurements indicate that the product consists of a large quantity of bone-like nanocrystals with lengths of 120–200 nm. The widths of these nanocrystals at both ends are in the range of 20–50 nm, which are 3–20 nm wider than those of the middle parts. Explorations of X-ray diffraction (XRD) and selected area electronic diffraction (SAED) exhibit that the product is high-quality cubic single-crystalline nanocrystals. The photoluminescence (PL) measurement suggests that the product has an intensive emission centered at 410 nm, showing that the product has potential application in optical devices. The advantages of our method lie in high yield, the easy availability of the starting materials and permitting large-scale production at low cost. The growth mechanism was proposed to be related with solvent’s oxidation in the precursor formation process and following nucleation and mass-transfer in the decomposition of the precursor.